-
Pass Labs 1INT-30A - page 1
1 INT -30A Owners Manual pass TM INT -30A Owner’ s Manual Aug 26, 2009 ...
-
Pass Labs 1INT-30A - page 2
2 INT -30A Owners Manual Please keep these instructions and heed all war nings. Use product only f or intended function. F or your protection please read the f ollowing: W ater and moisture: Electrical devices should not be used near w ater (as per example, near a bathtub , w ashbasin, kitchen sink, laundry tub , wet basement or swimming pool. ) Ca ...
-
Pass Labs 1INT-30A - page 3
3 INT -30A Owners Manual Cr ush and Tip Hazard: When moving or placing these products use caution to av oid injur y from tip-over or fall. Mak e sure that any stand, cart, table, bracket or tripod used to support this product is weight rated sufficient to the task. Ser vicing: T o reduce the risk of fire, electrical shock or other injuries , the us ...
-
Pass Labs 1INT-30A - page 4
4 INT -30A Owners Manual Nelson P ass has been designing audio electronics professionally since about 1971, first with ESS (remember Heil Air Motion transfor mers?), and then for ming a new company , Threshold in 1975. T hreshold pioneered the design of high pow er Class A pow er amplifiers and later , high pow er amplifiers using only local feedba ...
-
Pass Labs 1INT-30A - page 5
5 INT -30A Owners Manual the distortion as identical as possible on both polarities of the balanced output. It is easier to make distortions in the two halv es more identical than to remov e them with feedback, and this is the operating principle of X amplifiers . Since the X1000, P ass Labs products have contin uously evolved to ward higher perfor ...
-
Pass Labs 1INT-30A - page 6
6 INT -30A Owners Manual satisfaction audio product. From a measured and subjecti ve view point this is an outstanding product, we trust you will sit back and listen with a big g rin on your face . If you hav e purchased this amplifier , we thank you for your confidence , and hope that you enjo y it for many years. If y ou need product ser vice, ha ...
-
Pass Labs 1INT-30A - page 7
7 INT -30A Owners Manual 1) V acuum Florescent display ; shows operational status . 2) Mute, indicator (Blue LED) 3) Stand-by P ow er on, indicator (Blue LED) 4) Stand-by P ow er on, momentar y push button (on / off) 5) Mute, momentary push-button (on / off) 6) Input selection buttons (inputs 1-4) 7) IR remote, recei ver window 8) V olume control A ...
-
Pass Labs 1INT-30A - page 8
8 INT -30A Owners Manual F or maximum safety we sugg est that the power cord should be the last cable installed on your po wer -amplifier . Y ou may , if you wish, substitute a 15-amp after market pow er cord for the one we ha ve supplied. Only use polarized po wer cords , which meet all local safety standards and car r y acceptance marks from the ...
-
Pass Labs 1INT-30A - page 9
9 INT -30A Owners Manual So the amplifier is sitting there unconnected. Make sure that the rear panel po wer switc h is off (down). Plug the A C cord into the back of the amplifier , and then into the wall. Then tur n the pow er switch on (up). The lights in your house ma y dim for a moment as the pow er supply charges the capacitors . Please note ...
-
Pass Labs 1INT-30A - page 10
10 INT -30A Owners Manual Choose either XLR or RCA inputs . If you r un both at once on a single input from different components , the sound is not likely to be optimal, but it shouldn ’t cause damage anywhere. Now that the source components and loudspeak ers are connected into the amplifier; plug the pow er cord back into the wall, and turn on t ...
-
Pass Labs 1INT-30A - page 11
11 INT -30A Owners Manual W e g o to a lot of trouble to make products reliable, and the failure rate of our amplifiers is very low . T his is small comfort to the few , but take it easy and giv e us a call if you hav e problems . P eople are interested in how long it takes for these amplifiers to break in. Depending on the resolution of the rest o ...
-
Pass Labs 1INT-30A - page 12
12 INT -30A Owners Manual Speaker cables should be fir mly tightened down at the speak er output ter minals , but not with a wrench. Output terminals will not withstand the levels of tor que that may be easily applied by wrench. Hand tightening without ex cessiv e force is plenty . Cleaning contact surfaces with one of the commercially av ailable e ...
-
Pass Labs 1INT-30A - page 13
13 INT -30A Owners Manual Please chec k with the factor y-authorized distributor in the countr y you are purchasing this product for specific w ar ranty infor mation. All Pass Laboratories products purchased from an authorized P ass Labora- tories dealer in Nor th America are covered by a transferable, limited 3-year warranty . This w ar rantee inc ...
¿Tienes una pregunta acerca de Pass Labs 1INT-30A?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Pass Labs 1INT-30A, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Pass Labs 1INT-30A probablemente compartirá una forma de solucionarlo.