-
VDO Cyclecomputing C05+ - page 1
BEDIENUNGSANLEITUNG INSTRUCTION MANUAL MANUEL D´INSTALLA TION ET D´UTILISATION MANUALE D´INSTALLAZIONE E FUNZIONAMENTO INSTALACION Y OPERACIÓN MANUAL HANDLEIDING NÁVOD K MONTÁŽI A OBSLUZE INSTRUKCJA OBSLUGI LICZNIKA INSTALLA TIONS OG BETJENINGSVEJLEDNING BRUKSANVISNING BRUKSANVISNING ASENNUS JA KÄYTTÖOHJEKIRJA CYCLECOMPUTING C05+ ...
-
VDO Cyclecomputing C05+ - page 2
1 GB INST ALLA TION AND OPERA TION MANUAL - VDO CYTEC C05+ Preface Thank you for buying a VDO CYTEC bicycle computer . The more familiar you get with this model, the more enjoyable your trips are going to be. Please read thoroughly all the information provided in this manual. Y ou are getting important and useful hints for operation to make you ful ...
-
VDO Cyclecomputing C05+ - page 3
GB 2 Warning: Before tightening the handlebar holder , make sure to adjust the position of the computer head (inclination) when the LCD-display is best visible for you. Only when you find the best position tighten the screw . screw ...
-
VDO Cyclecomputing C05+ - page 4
3 GB 1.2 Mounting the speed transmitter / sender The sensor should be mounted on the same side of the fork as the holder is on the handlebar . Make sure to position the respective rubber shim between fork and sender , position the curved back of the sender next to the spokes and make sure the sender is aimed at the receiver (computer head). Importa ...
-
VDO Cyclecomputing C05+ - page 5
GB 4 1.3 Mounting the spoke magnet Distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current positioning, slide the sensor and the magnet on the fork or spoke accordingly . Watch out: Please remove the computerhead from the handlebar holder when you intend not to use your bike for a longer p ...
-
VDO Cyclecomputing C05+ - page 6
5 GB 1.4 Installing battery into computer head T o save battery power , your VDO CYTEC C05+ comes with the battery not yet fitted. Prior to initial use you have to install the battery first. Insert battery with positive (+) end on top. Watch out: Once the battery is properly fitted, the computer immediately changes into set-up mode (see also chapte ...
-
VDO Cyclecomputing C05+ - page 7
GB 6 1.5 Function Indicator Y our VDO CYTEC C05+ features a function indicator ((1)). When you are done mounting the computer , ((1)) flashes at the first rotation of the wheel. When the wheel-size is properly entered, actual speed is displayed as well.(see chapter 5). In case the function-indicator ((1)) is not flashing, please double-check: Is th ...
-
VDO Cyclecomputing C05+ - page 8
7 GB UNLOCK LOCK 1.LOCK 2.CLICK 1.PRESS 2.UNLOCK ...
-
VDO Cyclecomputing C05+ - page 9
GB 8 3. Information features of your VDO CYTEC C05+ Y our VDO CYTEC C05+ provides you with following information: KMH-MPH current speed indicated in either KMH or MPH, featuring automatic conversion into MPH DST trip counter , counts your trip distance up to 999,99 km or miles. A TM trip timer , keeps track of the actual riding time featuring autom ...
-
VDO Cyclecomputing C05+ - page 10
This button / key has several functions. All functions of the button / key are outlined in the chart below. Y our display Button / Key to Length of pushing What is going on? indicates following be pushed the button / key information DST -ODO-CLK-A TM push MODE key brief (0.1 sec) next information from DST or ODO or A TM is indicated. ODO push MODE ...
-
VDO Cyclecomputing C05+ - page 11
GB 10 5.1 Programming (setting up) your wheelsize In order for the VDO CYTEC C05+ to indicate your actual speed and your trip distance, the correct wheelsize has to be entered. Wheelsize is the outer circumference of the wheel including the tire. following default is entered wheelsize = WS = 2124 mm Watch out: Above default is automatically applied ...
-
VDO Cyclecomputing C05+ - page 12
11 GB Watch out: In case you have selected MPH readout you must enter your wheelsize in mm. WS in mm 1x ...
-
VDO Cyclecomputing C05+ - page 13
GB 12 5.3 Entering your wheelsize / entering odometer After initially installing the battery or after a battery change, your VDO CYTEC C05+ automatically switches into set-up mode for wheelsize and odometer . Start with Step 3. Y ou might as well enter the set-up mode for wheelsize and odometer at any time by proceeding as follows: Step 1: Call ODO ...
-
VDO Cyclecomputing C05+ - page 14
13 GB In case you wish to enter the precise wheelsize you have measured yourself (i.e. 2257), please proceed with step 5. Step 5 : Not pressing the MODE button with in 2 seconds will make the last digit (212 4 ) flash and change the value (4-5-6-7...) Once the correct digit (7) comes up, press the mode button. Now the third digit flashes and change ...
-
VDO Cyclecomputing C05+ - page 15
GB 14 Press immediatly 5 times to end Press to Stop switch to next Press to Stop switch to next Press to Stop switch to next Press to Stop switch to next Press to Stop switch to next Please wait 2 sec. until counting Press to Stop switch to next Press to Stop switch to next Press to Stop switch to next Press to switch Set ODOMETER Return to main Di ...
-
VDO Cyclecomputing C05+ - page 16
15 GB 5.4 Setting the clock CLK Y our VDO CYTEC C05+ features a clock with hour and minute display in 24 h mode T o access the clock set-up mode proceed as follows: Step 1: call in the CLK information into your display Step 2: Press the MODE button for 5 sec. The set-up mode for the clock starts. Y ou will see the digit flashing and changing its va ...
-
VDO Cyclecomputing C05+ - page 17
6. Resetting information to zero The following information may be reset to zero with your VDO CYTEC C05+: DST = trip distance A TM = trip counter Watch out: Both these information are simultaneously reset to zero T o reset either DST or A TM, one of these informations has to be displayed. Resetting to zero is done by pressing the MODE button for fi ...
-
VDO Cyclecomputing C05+ - page 18
Hg 17 GB 8 . Battery change Tip: Take down your total distance and wheelsize prior to battery change. 8.1 Changing the battery in the computer head see chapter 1.4. Watch ou t : old batteries require special disposal 9. T roubleshooting This chart outlines possible malfunctions, their causes and solutions. malfunction possible cause solutions speed ...
-
VDO Cyclecomputing C05+ - page 19
GB 18 8 . Battery change Tip: Take down your total distance and wheelsize prior to battery change. 8.1 Changing the battery in the computer head see chapter 1.4. Watch ou t : old batteries require special disposal 9. T roubleshooting This chart outlines possible malfunctions, their causes and solutions. malfunction possible cause solutions speed di ...
-
VDO Cyclecomputing C05+ - page 20
19 GB Contents 1 computer head 1 handlebar holder with screw 1 wireless transmitter with battery 12 V , type V23GA 1 rubber shim for sensor mount 1 spoke magnet 5 cable ties 1 battery 3 V , type CR 2032 1 installation and operation manual TIP The CYTEC tin box easily holds a mini-tool and a spare tube to carry on with your ride. ...
¿Tienes una pregunta acerca de VDO Cyclecomputing C05+?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con VDO Cyclecomputing C05+, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con VDO Cyclecomputing C05+ probablemente compartirá una forma de solucionarlo.