Español dropdown-ico

Manual de instrucciones Extron electronic IPL T S Series

79 de páginas 5.77 mb
Descargar

Pasar a la página of 79

Summary
  • Extron electronic IPL T S Series - page 1

    IPL T S Series IP Link ® Ether net Contr ol Interfaces 68-1218-01 Rev . D 12 08 ...

  • Extron electronic IPL T S Series - page 2

    This symbol is intended to alert the user of important operating and maintenance (servicing) instructions in the literature provided with the equipment. This symbol is intended to alert the user of the presence of uninsulated dangerous voltage within the product’ s enclosure that may present a risk of electric shock. Caution Read Instructions • ...

  • Extron electronic IPL T S Series - page 3

    i IPL T S Series FCC Class A Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interfer ence received, including int ...

  • Extron electronic IPL T S Series - page 4

    IPL T S Series ii ...

  • Extron electronic IPL T S Series - page 5

    QS-1 IPL T S Series • Quick Start Step 1 T urn power off and disconnect the device fr om its power source. Step 2 Mount the IPL T S Series unit: • on a projector IP L T S 2 1 R 1 0 0 C O M T X R X R T S C T S L I N K A C T 2 2 4 Ceiling Mounting Bolt Projector Mounting Bra cke t Projector Mount • under a desk IPL T S2 1 R 100 COM TX LINK ACT ...

  • Extron electronic IPL T S Series - page 6

    IPL T S Series • Quick Start QS-2 Quick Start — IPL T S Series, cont’d ...

  • Extron electronic IPL T S Series - page 7

    i IPL T S Series • T able of Contents PRELIMINAR Y T able of Contents Chapter One • Introduction ...................................................................................................... 1-1 About This Manual .................................................................................................................... 1-2 Abo ...

  • Extron electronic IPL T S Series - page 8

    T able of Contents, cont’d IPL T S Series • T able of Contents ii 68-1218-01 Rev . D 12 08 All trademarks mentioned in this manual are the properties of their respective owners. File Management page .......................................................................................................... 3-14 Configuration using DataViewer ... ...

  • Extron electronic IPL T S Series - page 9

    IPL T S Series 1 Chapter One Intr oduction About This Manual About the IPL T S Series Interface Features ...

  • Extron electronic IPL T S Series - page 10

    IPL T S Series • Introduction 1-2 Intr oduction About This Manual This manual describes the function, installation, configuration, and operation of the Extron IPL T S Series interface devices which are shown below . About the IPL T S Series Interface The Extron IPL T S Series interface devices integrate network connectivity into audio/video (A/V ...

  • Extron electronic IPL T S Series - page 11

    1-3 IPL T S Series • Introduction Each IPL T S Series interface comes with Extron’s IP Link ® technology including: • A built-in W eb server • A set of W eb pages that can be used to congure the device • Flash memory to store Extr on’s GlobalV iewer ® application and A/V equipment device drivers • Compatibility with Extron’s fr ...

  • Extron electronic IPL T S Series - page 12

    Intr oduction, cont’d IPL T S Series • Introduction 1-4 W eb-based A/V asset management — When used with GlobalV iewer software, the IPL T S interfaces provide a powerful, flexible way to manage, monitor , and control pr ojectors, flat-panel displays, and other devices using a standard Ethernet network. Integral, high performance W eb serve ...

  • Extron electronic IPL T S Series - page 13

    IPL T S Series 2 Chapter T wo Installation and Operation Installation Overview Mounting the IPL T S Interface Rear Panel Features and Cabling Operation ...

  • Extron electronic IPL T S Series - page 14

    IPL T S Series • Installation and Operation 2-2 Installation and Operation Installation Overview T o install and set up an IPL T S interface, follow these steps: 1 . T urn all of the equipment off. Make sur e that the video sources (DSS, cable boxes, or other devices), the IPL T S unit, the output devices (monitors, VCRs, projectors, etc.) and th ...

  • Extron electronic IPL T S Series - page 15

    2-3 IPL T S Series • Installation and Operation Mounting options All units are easily mounted in a rack, under a desk or podium, or on a pr ojector mount. Mounting kits and IPL T S Series device compatibility are shown in the table below . Mounting T ype Kit PN S1 S2 S4 S6 Under-furnitur e mount 70-077-01 • Under-furnitur e mount 70-212-01 • ...

  • Extron electronic IPL T S Series - page 16

    IPL T S Series • Installation and Operation 2-4 Installation and Operation, cont’d IPL T S2 1 R 100 COM TX LINK ACT 2 RX RTS CTS IPL T S2 1 R 100 COM TX LINK ACT 2 RX RTS CTS MDA SERIES DISTRIBUTION AMPLIFIER ® ® Figure 2-2 — Mounting the interface on the standar d shelf Furniture or projector mounting The following furniture and pr ojector ...

  • Extron electronic IPL T S Series - page 17

    2-5 IPL T S Series • Installation and Operation IP L T S 2 1 R 100 COM TX LINK ACT 2 RX RTS CTS Furniture Mount Projector Mount IPL T S2 1 R 100 COM TX RX RT S CTS LINK ACT 2 2 4 Digital Projector Mounting Bolt Projector Mounting Bra cke t Figure 2-3 — Mounting the interface Rear Panel Featur es and Cabling All connections, including power , co ...

  • Extron electronic IPL T S Series - page 18

    IPL T S Series • Installation 2-6 PRELIMINAR Y IPL T S Series • Installation and Operation 2-6 Installation and Operation, cont’d COM1 LAN POWER 12V .5A MAX COM5 TX RX TX RX COM6 COM3 TX RX TX RX COM4 COM2 00-05-A6-00-00-06 6 10 7 5 1 2 4 3 Figure 2-7 — IPL T S6 interface back panel Power a Power connection — Plug the unit’s external 12 ...

  • Extron electronic IPL T S Series - page 19

    2-7 IPL T S Series • Installation and Operation PRELIMINAR Y 2-7 Ethernet/LAN b LAN Activity LED — A blinking yellow LED indicates LAN activity . c LAN connector — An RJ-45 connector for a network connection. Use an Ethernet straight-through cable to connect to a switch, hub, or r outer , or an Ethernet crossover cable to connect dir ectly to ...

  • Extron electronic IPL T S Series - page 20

    Installation and Operation, cont’d IPL T S Series • Installation 2-8 Factory default protocol for the contr ol interface is: • RS-232 • 9600 baud • no parity • 8 data bits • 1 stop bit • pacing = 0 ms • handshaking = off Communication to an attached device can be done through the IPL T S Series device’s default W eb pages or by ...

  • Extron electronic IPL T S Series - page 21

    2-9 IPL T S Series • Installation and Operation COM ports 1 and 2 of the IPL T S2 can be wired in a similar way as the IPL T S6, as shown in gure 2-10. Both can be wir ed using a 3.5 mm, 5-pole or 3-pole captive screw connector . N The IPL T S2 allows for use of either the 9-pin D connector on COM1 or COM2. The 9-pin D connector COM ports and ...

  • Extron electronic IPL T S Series - page 22

    Installation and Operation, cont’d IPL T S Series • Installation and Operation 2-10 IPL T S4 R 100 LINK AC T 1 COM TX 2 RX RTS CTS 3 TX 4 RX RTS CTS 9 7 8 1 3 2 4 5 6 3 4 5 6 Figure 2-13 — IPL T S4 fr ont panel IPL T S6 R 100 LINK AC T 1 COM TX 2 RX RTS CTS 3 COM TX 4 5 6 RX TX RX 1 3 2 4 5 6 9 7 8 3 4 3 4 Figure 2-14 — IPL T S6 fr ont pane ...

  • Extron electronic IPL T S Series - page 23

    2-11 IPL T S Series • Installation and Operation N If the Reset button is continuosly held down, every three seconds the LED pulses (blinks) and puts the unit in a different mode. The Mode 5 LED blinks thr ee times, the third blink indicating that it is the last mode. The following modes are separate functions, not a continuation from Mode 1 to M ...

  • Extron electronic IPL T S Series - page 24

    Installation and Operation, cont’d IPL T S Series • Installation and Operation 2-12 ...

  • Extron electronic IPL T S Series - page 25

    IPL T S Series 3 Chapter Thr ee Connection and Configuration Connecting the Hardware Setting the Internet Protocol (IP) Address Configuration using Global Configurator Configuration using Embedded W eb Pages Configuration using DataViewer ...

  • Extron electronic IPL T S Series - page 26

    IPL T S Series • Connection and Conguration 3-2 Connection and Configuration Connecting the Har dwar e T o connect the IPL T S interface, connect the input and output devices to the unit. Use gure 3-1, below , as a guide. COM 1 LAN UID# 093012052 PO W ER 12V .5A MAX CO M1 T XR X TX RX CO M2 COM 2 Extron IPL T S2 Ethernet Control Interface ...

  • Extron electronic IPL T S Series - page 27

    3-3 IPL T S Series • Connection and Conguration COM 3 LAN UID# 093012052 POWER 12V .5A MAX COM 2 COM 1 COM 2 Lighting Control Ethe rn et RS-232 RS-232 RS-232 DV D Laptop VCR Remote User Control and Administrator Monitoring Projector Extron MA V 62 Matrix Switcher TCP/IP Network Extron IPL T S4 Ethernet Control Interface Extron MediaLink Contro ...

  • Extron electronic IPL T S Series - page 28

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-4 IPL T S4 R 100 LINK AC T 1 COM TX 2 RX RTS CTS 3 TX 4 RX RTS CTS 1 2 Figure 3-3 — IPL T S unit’ s front panel a Power LED — On green with power . Blinks four times to conrm a Mode 4 reset. b Reset button — The Reset button is recessed. Use an Ext ...

  • Extron electronic IPL T S Series - page 29

    3-5 IPL T S Series • Connection and Conguration Figure 3-4 — Setting the IP addr ess in Global Configurator Setting the IP address using embedded W eb pages Each IPL T S unit contains an on-board W eb server with interactive pages that can be used to configure the device. The IPL T S unit must be at its factory default IP address. T o set ...

  • Extron electronic IPL T S Series - page 30

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-6 5 . Click OK . Figure 3-5 — Internet Protocol (TCP/IP) Pr operties dialog box 6 . Open a W eb browser on the local PC. 7 . Enter 192.168.254.254 in the browser ’s Address eld and press the Enter key . The IPL T S unit’s embedded W eb page is displa ...

  • Extron electronic IPL T S Series - page 31

    3-7 IPL T S Series • Connection and Conguration Figure 3-6 — W eb server System Settings screen T o r eturn the local PC to its original TCP/IP settings: 1 . Close the W eb br owser . 2 . Disconnect the Ethernet cr ossover cable from the PC and the device. 3 . Return to the TCP/IP Properties dialog box on the PC. 4 . Return the IP address, S ...

  • Extron electronic IPL T S Series - page 32

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-8 Figure 3-7 — Executing the ARP command 3 . T o confirm the new IP addr ess is active, perform a ping command to the new IP addr ess. example: C:> ping 10.13.197.64 If the IP addr ess setting was successful, the device replies 3 or more times: Reply f ...

  • Extron electronic IPL T S Series - page 33

    3-9 IPL T S Series • Connection and Conguration Figure 3-8 — Global Configurator Once installed on your local PC, Global Congurator can be used to congure your IPL T S Series device and the A/V devices that ar e attached to the S Series’ serial control ports. See the Global Congurator help le for instructions on how to: • Do ...

  • Extron electronic IPL T S Series - page 34

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-10 Connecting via the Web server pages T o connect to an IPL T S Series device via its W eb server pages: 1 . Open a W eb browser on a local PC. 2 . Enter the device’s IP addr ess in the browser ’s Addr ess field and press the Enter key . If the device i ...

  • Extron electronic IPL T S Series - page 35

    3-11 IPL T S Series • Connection and Conguration System Status page The System Status page is a read-only page that pr ovides the following status information: • System Description — Model, Description, Part Number , Firmware, Date, and T ime • IP Settings — Unit Name, DHCP setting, IP Address, Gateway IP Address, Subnet Mask, and MAC ...

  • Extron electronic IPL T S Series - page 36

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-12 Figure 3-12 — System Settings scr een Port Settings The Port Settings page grants access to view or change the Serial Port Settings: • Serial port number — use a radio button to select the desired port • Port type — RS-232 (default), RS-422, 4S-4 ...

  • Extron electronic IPL T S Series - page 37

    3-13 IPL T S Series • Connection and Conguration Passwords The Passwords page fields include: • Administrator Password — pr ovides complete configuration control • User Password — allows view of configuration only Figure 3-14 — Passwords scr een T o clear a password, enter a single space, r epeat the entry in the re-enter password ? ...

  • Extron electronic IPL T S Series - page 38

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-14 Figure 3-15 — Email Alerts screen Firmware Upgrade The Firmware Upgrade page r eports the current rmware level, and pr ovides the capability to browse to and upload a new firmwar e file. Figure 3-16 — Firmwar e Upgrade screen File Management page ...

  • Extron electronic IPL T S Series - page 39

    3-15 IPL T S Series • Connection and Conguration Configuration using DataV iewer DataV iewer is an enhanced terminal emulation program that facilitates analysis of RS-232 and TCP/IP communication with Extr on devices. The software allows users to send commands to a device and view the device’s responses in ASCII or hexadecimal format. Comma ...

  • Extron electronic IPL T S Series - page 40

    Connection and Configuration, cont’d IPL T S Series • Connection and Conguration 3-16 3 . Enter the device’s IP addr ess in the Hostname/IP Address eld. 4 . Click OK . Figure 3-19 — Communication Setup dialog box The DataV iewer application opens (see gure 3-16). See the DataV iewer help le for information on sending commands t ...

  • Extron electronic IPL T S Series - page 41

    IPL T S Series 4 Chapter Four Communication and Contr ol Programmer’ s Guide for T elnet and W eb Browsers Customization Advanced Serial Port Control T roubleshooting ...

  • Extron electronic IPL T S Series - page 42

    IPL T S Series • Communication and Control 4-2 Communication and Contr ol Pr ogrammer’ s Guide for T elnet and Web Br owsers Using the command/response table The following are either T elnet (port 23) or W eb br owser (port 80) commands. There ar e some minor differences when you ar e implementing these commands via T elnet or via URL encoding ...

  • Extron electronic IPL T S Series - page 43

    4-3 IPL T S Series • Communication and Control Symbol definitions ] = CR/LF (carriage return/line feed) } = Carriage return (no line feed) • = Space character X! = Specic port number (01-99) The port number is represented as two ASCII characters (2 bytes). For example, port 05 would be repr esented as 30 35 in hex. X@ = Command data section ...

  • Extron electronic IPL T S Series - page 44

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-4 X3$ = Daylight saving time (DST) is a 1-hour offset (for the USA only) that begins on the rst Sunday of April at 2 am and ends on the last Sunday of October . For example, time in California is GMT -8:00 from April to October and GMT -7:00 from November to Marc ...

  • Extron electronic IPL T S Series - page 45

    4-5 IPL T S Series • Communication and Control are the same for both administrator and user , the unit defaults to administrator privileges. Error r esponses When the IPL T S interface receives a valid command, it executes the command and sends a response to the host device. If the unit is unable to execute the command because the command contain ...

  • Extron electronic IPL T S Series - page 46

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-6 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Bidirectional serial data port Send data string E X! * X1& * X2) * X2! RS }X@ W X! %2A X1& %2A X2) %2A X2! RS |X@ response fr om command ...

  • Extron electronic IPL T S Series - page 47

    4-7 IPL T S Series • Communication and Control Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Configure parameters 24 E X! * X2% , X2^ , X2& , X2* CP } W X! %2A X2% %2C X2^ %2C X2& %2C X2* CP | Cpn X! •Ccp X2% , X2^ , X2& , X2* ] Set baud rate ( X2% ), parity ( ...

  • Extron electronic IPL T S Series - page 48

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-8 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description V iew pass-thru mode 24 E X! CD } W X! CD | X5) , X5# , X2!] Ethernet data port Set current connection port timeout E 0* X6( TC } W0%2A X6( TC | ...

  • Extron electronic IPL T S Series - page 49

    4-9 IPL T S Series • Communication and Control Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Firmware version, part number and information r equests N In a query response, an asterisk ( * ) after the version number indicates the version that is curr ently used. A question ma ...

  • Extron electronic IPL T S Series - page 50

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-10 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Query part number N N 60-xxx-yy ] or Pno60-xxx-yy ] Show the IPL T S unit’s part #. Query model name 1I 1I IPL T xxxx ] or Inf01*IPL T xxxx ] ...

  • Extron electronic IPL T S Series - page 51

    4-11 IPL T S Series • Communication and Control Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Send e-mail (using differ ent file) 24 E X4% , X7) , X4& SM } W X4% %2C X7) %2C X4& SM | Eml X4% ] X7) = The number to insert into an e-mail message if a ____ .eml file ha ...

  • Extron electronic IPL T S Series - page 52

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-12 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Web br owser -specific Read response fr om last URL command E UB } WUB | response fr om command ] IP setup commands Set unit name 24 E X1@ CN } ...

  • Extron electronic IPL T S Series - page 53

    4-13 IPL T S Series • Communication and Control Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Set verbose mode 24 E X2@ CV } W X2@ CV | V rb X2@ ] Enable or disable the verbose mode via this command. For X2@ : 0 = c le ar/ no ne, d efa ul t f or T eln et co nne ct ion s; res ...

  • Extron electronic IPL T S Series - page 54

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-14 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description V iew broadcast port and MAC E PB } WPB | {port}* X1*] N {port#} = UDP outgoing port, X7! * X7@ = MAC address for UDP unicast transmissions. N C ...

  • Extron electronic IPL T S Series - page 55

    4-15 IPL T S Series • Communication and Control Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Remap port designations For security reasons the network administrator may wish to assign new/dif ferent port numbers to the contr oller ’s T elnet, W eb browser , and direct acce ...

  • Extron electronic IPL T S Series - page 56

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-16 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Directories Change/create a directory E path/dir ectory/CJ } Wpath/directory/CJ | Dir•path/dir ectory/ ] The directory’s name must be compos ...

  • Extron electronic IPL T S Series - page 57

    4-17 IPL T S Series • Communication and Control Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Erase current directory and subdirectories 24 28 E //EF } W//EF | Ddl ] List files from curr ent directory E DF } WDF | Get connection listing E CC } WCC | [number of connections] ...

  • Extron electronic IPL T S Series - page 58

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-18 Command ASCII (T elnet) (host to unit) URL Encoded (Web) (host to unit) Response (unit to host) Additional description Absolute system reset 24 E ZQQQ } W ZQQQ | Zpq ] This r esets all device settings/memories to factory default; however , the firmware version r ...

  • Extron electronic IPL T S Series - page 59

    4-19 IPL T S Series • Communication and Control Customization In the IPL T S interface series of products, varying degrees of customization are possible. Custom W eb pages allow you to cr eate customized W eb pages to control your A/V devices. Server Side Includes (SSI) makes it possible to obtain information from the unit and to display it on W ...

  • Extron electronic IPL T S Series - page 60

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-20 <!--#echo var= "" --> W Delimiter Delimiter SIS Command Server Side In cl ude Using a Remote SIS command *T ype with no spaces. Po rt Number 1* ** Time to wa it for first character of response 50 Time between characters in response 3 Command RS L ...

  • Extron electronic IPL T S Series - page 61

    4-21 IPL T S Series • Communication and Control Code examples This section shows practical uses for both SSIs and query strings. Example 1 In figure below , both host SSI and r emote SSI commands are used within the same W eb page. Y ou will notice six SSIs: thr ee host commands and three remote commands. <html> <head><title>Ex ...

  • Extron electronic IPL T S Series - page 62

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-22 Figure 4-6b — Br owser view of previous HTML source code Example 2 The example below shows how a simple hyperlink and a remote query string can be used to build a W eb page that can control a device. <html> <head><title>Example 2</title> ...

  • Extron electronic IPL T S Series - page 63

    4-23 IPL T S Series • Communication and Control Figure 4-7b — Br owser view of previous HTML source code N Before attempting to develop new W eb pages, the user should have a working knowledge of JavaScript, HTML, and SSI. URL encoding URL encoding is the method of using ASCII hexadecimal characters to display specic characters in a URL. URL ...

  • Extron electronic IPL T S Series - page 64

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-24 Characters $ & + , / : ; = ? @ Dollar Ampersand Plus Comma Fo rward slash / virgule Colon Semi-colon Equal Question mark “At” symbol 24 26 2B 2C 2F 3A 3B 3D 3F 40 36 38 43 44 47 58 59 61 63 64 Hex Dec Unsafe characters URLs use some characters for “spec ...

  • Extron electronic IPL T S Series - page 65

    4-25 IPL T S Series • Communication and Control C O M 1 LA N U ID # 093012052 POWER 1 2 V .5 A M A X C O M 1 TX RX T XR X C O M 2 C O M 2 Ethernet RS-232 RS-232 Remote User Control & Administrator Monitoring Projector TCP/IP Netwo rk Extron IPL T S2 Ethernet Control Interface Extron M ed iaLink C on troller M L C 2 0 6 D IS P L A Y P O W E R ...

  • Extron electronic IPL T S Series - page 66

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-26 Figure 4-9 — DataViewer Communication Setup dialog box 5. Click OK . The DataV iewer commands window opens. 6. Send serial commands directly thr ough the selected COM port to the attached A/V device. 7. T o end the direct access session, close DataV iewer . N Y ...

  • Extron electronic IPL T S Series - page 67

    4-27 IPL T S Series • Communication and Control COM 1 LAN 12V .5A M A X COM 3 LAN UID# 093012052 POWER 12V .5A MA X COM 2 COM 1 COM 2 RS-232 Plasma Display Box 1 Box 2 PC running serial control software or a serial controller. Extron IPL T S4 Ethernet Control Interface RS-232 Ethernet Extron IPL T S1 Ethernet Control Interface TCP/IP Network Figu ...

  • Extron electronic IPL T S Series - page 68

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-28 Figure 4-11 — The Port Settings page on unit 2 5. In the Remote IP Address field, enter the dir ect access IP addr ess of unit 1. 6. In the Remote TCP Port field, enter the port number (2001-2006) that is serially attached to unit 1. 7. Click the Submit butto ...

  • Extron electronic IPL T S Series - page 69

    4-29 IPL T S Series • Communication and Control 2. T ry to “ping” the unit by entering “ping 192.168.254.254” at the DOS command prompt, or use the IP or W eb address provided to you by your system administrator . If you get no response: a. Make sure your unit is using the appr opriate subnet mask (check with your system administrator). b ...

  • Extron electronic IPL T S Series - page 70

    Communication and Contr ol, cont’d IPL T S Series • Communication and Control 4-30 ...

  • Extron electronic IPL T S Series - page 71

    IPL T S Series A Appendix A Specifications, Part Numbers, Accessories Specifications Part Numbers and Accessories ...

  • Extron electronic IPL T S Series - page 72

    IPL T S Series • Specications, Part Numbers, Accessories A-2 Specifications, Part Numbers, Accessories Specifications Ethernet control interface Connectors ..................................... 1 RJ-45 female connector Data rate ......................................... 10/100Base-T , half/full duplex with autodetect Protocols .............. ...

  • Extron electronic IPL T S Series - page 73

    A-3 IPL T S Series • Specications, Part Numbers, Accessories Mounting Rack mount ........................ Y es, with optional 1U, 9.5" deep rack shelf (RSU 129, #60-190-01; RSB 129, 60-604-01); or V ersaT ools ® 1U, 3.5" deep rack shelf (RSF 123, #60-190-20; RSB 123, 60-604-20) Furniture mount IPL T S1 ....................... Under- ...

  • Extron electronic IPL T S Series - page 74

    Specifications, Part Numbers, Accessories, cont’d IPL T S Series • Specications, Part Numbers, Accessories A-4 Part Numbers and Accessories Included parts Included parts Replacement part number IPL T S1 60-801-81 IPL T S2 60-544-81 IPL T S4 60-544-83 IPL T S6 60-544-84 Power supply; external 12 VDC, 1 A (U.S., Canada) 70-055-01 Power supply ...

  • Extron electronic IPL T S Series - page 75

    IPL T S Series B Appendix B Glossary Glossary ...

  • Extron electronic IPL T S Series - page 76

    IPL T S Series • Glossary B-2 Glossary Glossary 10/100Base-T is Ethernet that uses Unshielded T wisted Pair (UTP - CA T 5, etc.) cable, on which the amount of data transmitted between two points in a given amount of time is equal to either 10 Mbps or 100 Mbps. Address Resolution Protocol (ARP) is a protocol that assigns an IP address to a device ...

  • Extron electronic IPL T S Series - page 77

    B-3 IPL T S Series • Glossary GlobalV iewer (GV) is a set of W eb pages (HTML, XML, JS) and graphics that are loaded into the memory of an IPL T S interface. These pages provide an interface for control of devices attached to the IPL T S interface. They communicate with the event scripts running on the device, and the event scripts issue the comm ...

  • Extron electronic IPL T S Series - page 78

    Extr on’ s W arranty Extron Electr onics warrants this product against defects in materials and workmanship for a period of three years from the date of pur chase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electr onics will, at its option, repair or replace said pr ...

  • Extron electronic IPL T S Series - page 79

    Ex tron US A - We st Headquar te rs +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .7 14 .4 91 .1 50 0 +1 .7 14 .4 91 .1 51 7 FA X Ex tron US A - East +8 00 .6 33 .9 87 6 Insid e U S A / C anad a O nl y +1 .9 19 .8 63 .1 79 4 +1 .9 19 .8 63 .1 79 7 FA X Ex tron Europe +8 00 .3 98 7. 66 73 Insid e E urop e O nl y +3 1. 33 .4 53 .4 04 0 +3 1. ...

Fabricante Extron electronic Categoría Network Card

Los documentos del dispositivo Extron electronic IPL T S Series que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Extron electronic
- manuales de instrucciones IPL T S Series
- hojas de producto Extron electronic
- folletos informativos
- o etiquetas energéticas Extron electronic IPL T S Series
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Extron electronic IPL T S Series.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Extron electronic IPL T S Series, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Extron electronic IPL T S Series. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Extron electronic IPL T S Series.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Extron electronic IPL T S Series, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Extron electronic IPL T S Series. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Extron electronic IPL T S Series.

El manual de instrucciones completo de Extron electronic debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Extron electronic IPL T S Series - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Extron electronic IPL T S Series, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Extron electronic IPL T S Series que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Extron electronic IPL T S Series - que deben facilitarnos los primeros pasos durante el uso de Extron electronic IPL T S Series
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Extron electronic IPL T S Series
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Extron electronic IPL T S Series en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Extron electronic IPL T S Series?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Extron electronic IPL T S Series, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Extron electronic IPL T S Series probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)