-
Makita 6703DW - page 1
Equipped with Electric Brake MODEL 6703D MODEL 6703DW With Fast Charger Capacities Bolt, nut and machine screw size 3 mm ~ 5 mm (1/8" - 3/16") INSTRUCTION MANUAL Overall Net IRPM) length weight 5 kg.cm - 37 kg.cm 333 mm 1.3 kg (0.4 ft.lbs - 2.7 ft.lbsl (13-118") (2.9 Ibs) Fastening torque No load speed 400 SPEC IF I CAT I 0 N S Batte ...
-
Makita 6703DW - page 2
I M PO RTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONME ...
-
Makita 6703DW - page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using ...
-
Makita 6703DW - page 4
VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user - as well as damage to the tool. If in doubt, DO NOT PLUG IN T ...
-
Makita 6703DW - page 5
IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER & BATTERY CARTRIDGE Length of Cord (Feet) AWG Size of Cord 1. 2. 3. 4. 5. 6. 7. 8. 9. 25 50 100 150 18 18 18 16 SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings on ( ...
-
Makita 6703DW - page 6
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the batte ...
-
Makita 6703DW - page 7
Installing or removing the battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool. To insert the battery cartridge, align the tongue on the battery cartridge with th ...
-
Makita 6703DW - page 8
When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely a couple of times. If you try to charge a cartridge from a just-operated t ...
-
Makita 6703DW - page 9
Switch action To start the tool, simply pull the trigger. Release the trigger to stop. CAUTIO N : Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direct ...
-
Makita 6703DW - page 10
Adjusting the fastening torque The fastening torque can be adjusted infi- nitely from approx. 5 kg . cm (0.4 ft . Ibs) to 37 kg . cm (2.7 ft . Ibs). To adjust it, loosen the two screws and turn the adjusting ring. Then tighten the screws to secure the adjusting ring. Refer to the table below fok relation between the numbers on the adjusting ring an ...
-
Makita 6703DW - page 11
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11 ...
-
Makita 6703DW - page 12
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use,of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. I Size 9 Fast charger Fast charger Charger 12 V ...
-
Makita 6703DW - page 13
Sep.--29-'94 US CORDLESS SCREWDRIVER Model 67031) Note: The switch and other part configurations may differ from country to country. 13 ...
-
Makita 6703DW - page 14
MODEL 6703D Sep-29-'94 US 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 $2D DESCRIPTION 1 1 1 1 1 2 1 2 1 1 1 2 1 1 1 1 1 1 1 1 1 1 $zD DESCRIPTION ~ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 11 21 31 41 52 61 71 81 91 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 Ring Spring 11 Flat Washer 12 Compression Spring 13 Sleeve ...
-
Makita 6703DW - page 15
Recycling the Battery The only way to dispose of a Makita battery is to recycle it. The law prohibits any other method of disposal. I Ni-Cd I To recycle the battery: 1. Remove the battery from the tool. 2. a). Take the battery to your nearest Makita Factory Service Center or b). Take the battery to your nearest Makita Authorized Service Center or D ...
¿Tienes una pregunta acerca de Makita 6703DW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 6703DW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 6703DW probablemente compartirá una forma de solucionarlo.