-
Directed Electronics 6 - page 1
model 700/6 ...
-
Directed Electronics 6 - page 2
2 © 2003 Directed Electronics, Inc ...
-
Directed Electronics 6 - page 3
3 T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing a Directed Audio power amplifier from Directed Electronics, the industry leader in high quality automotive security and audio equipment since 1990. Directed Audio power amplifiers continue to set new standards of perfor- mance, reliability , and affordability in the mobile electron ...
-
Directed Electronics 6 - page 4
LIMITED TWO-YEAR CONSUMER W ARRANTY 4 © 2003 Directed Electronics, Inc Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workman- ship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the ...
-
Directed Electronics 6 - page 5
5 © 2003 Directed Electronics, Inc High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result. They may also impair a driver’ s ability to hear traffic sounds or emergency vehi- cles. Use common sense and practice safe listening habits when listening to or adjusting your audio syst ...
-
Directed Electronics 6 - page 6
6 © 2003 Directed Electronics, Inc INST ALLA TION GUIDELINES 1. Please read this owner’ s manual carefully before installing this ampli- fier . 2. Disconnect the batter y ground terminal prior to making any elec- trical connections. 3. Check for any hazards or obstruc- tions such as gas tanks, fuel or brake lines, and wiring harnesses before mou ...
-
Directed Electronics 6 - page 7
7 © 2003 Directed Electronics, Inc speaker load, the more heat is generated. For low impedance speaker applications or restricted ventilation installations, an external cooling fan may be advisable. 9. Batter y and ground connections to the vehicle should be made with crimped ring terminals of the appro- priate size (surface area is what counts); ...
-
Directed Electronics 6 - page 8
8 © 2003 Directed Electronics, Inc 1. R R C C A A I I n n p p u u t t J J a a c c k k s s - - Accepts line level outputs from head units or signal processors at voltages between 150mV and 8 volts. 2. R R C C A A O O u u t t p p u u t t J J a a c c k k s s - - These pass through RCA jacks can be used to send a signal to a second amplifier . It is t ...
-
Directed Electronics 6 - page 9
9 © 2003 Directed Electronics, Inc REM GND BAT T 30A x 2 FUSE RR LL CH 1+2 CH 3+4 CH 5+6 BRIDGE R L L R SPEAKER OUTPUT FIGURE 2—AMPLIFIER CONNECTIONS 700/6 REAR 1 4 2 5 1. S S p p e e a a k k e e r r O O u u t t T T e e r r m m i i n n a a l l s s - Connect the speakers to these terminals. (Refer to the Speaker Wiring Diagrams section of this gu ...
-
Directed Electronics 6 - page 10
10 © 2003 Directed Electronics, Inc TOP P ANEL CONTROLS LPF HPF FLAT BASS EQ OFF ON FREQ FREQ FREQ 50Hz 50Hz 50Hz 500Hz 500Hz 500Hz LPF LPF HPF HPF FLA T FLA T 5+6 GAIN 1+2 3+4 5+6 INPUT INPUT 3+4 5+6 GAIN GAIN MIN MIN MIN MAX MAX MAX OFF OFF ON ON FIGURE 3—AMPLIFIER CONTROLS 700/6 TOP 5 1. I I n n p p u u t t G G a a i i n n A A d d j j u u s s ...
-
Directed Electronics 6 - page 11
SPEAKER WIRING DIAGRAMS 11 © 2003 Directed Electronics, Inc Control Panel Cover The gain and filter controls are located under a control panel cover on top of the amplifier . The control panel cover must be removed to gain access to the gain and filter controls. Remove/Install Four Allen-head screws hold the control panel cover to the amplifier to ...
-
Directed Electronics 6 - page 12
12 © 2003 Directed Electronics, Inc T ri amp operation (top view) Bridged operation (top view) Three Channel N N O O T T E E : : When wiring the 700/6 for three channel operation, connect the left audio signal to both channels one and two RCA jacks and the right audio signal to both channels three and four RCA jacks using RCA Y adapters. ...
-
Directed Electronics 6 - page 13
13 CROSSOVER SETTINGS AND GAIN ADJUSTMENT Y our Directed Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier . For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should be set to FLA T . If the amplifier ...
-
Directed Electronics 6 - page 14
SPECIFICA TIONS 14 © 2003 Directed Electronics, Inc RMS continuous power per channel, Channels 1-4 driven into 4 ohms from 20 to 20,000 Hz, with less than 0.08% total Harmonic Distortion @ 14.4 VDC. Channel 5-6 driven into 4 ohms from 20-250 Hz, with less than 0.08% THD @ 14.4 VDC. RMS continuous power per channel, Channels 1-4 driven into 2 ohms ...
-
Directed Electronics 6 - page 15
The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology , Directed is ISO 9001 r ...
¿Tienes una pregunta acerca de Directed Electronics 6?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Directed Electronics 6, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Directed Electronics 6 probablemente compartirá una forma de solucionarlo.