-
Jonsered GC2236 - page 1
English GC2236 Operator ′ s manual Please read the oper ator’ s manual carefully and make sure y ou understand the instructions before using the machine. ...
-
Jonsered GC2236 - page 2
KEY T O SYMBOLS 2 – English Symbols W ARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’ s manual. Please read the operator’ s manual carefully and make ...
-
Jonsered GC2236 - page 3
CONTENTS English – 3 Contents Note the f ollowing bef ore starting: Please read the oper ator’ s manual carefully . KEY T O SYMBOLS Symbols ................................................................ 2 CONTENTS Contents ............................................................... 3 Note the follo wing before starting: .................. ...
-
Jonsered GC2236 - page 4
4 – English INTR ODUCTION Dear Customer , Cong ratulations on your choice to b uy a Jonsered product! We are con vinced that you will appreciate with g reat satisfaction the quality and perf or mance of our product for a very long time to come. The purchase of one of our products giv es you access to professional help with repairs and service whe ...
-
Jonsered GC2236 - page 5
English – 5 WHA T IS WHA T? What is what on the brushcutter? 32 31 30 23 23 25 26 27 28 24 29 1 T rimmer head 2 Grease filler cap, be vel gear 3 Bev el gear 4 Cutting attachment guard 5 Shaft 6 Handle adjustment 7 Loop handle 8 Suspension ring 9 Stop switch 10 Throttle lock out 11 Throttle control 12 Spark plug cap and spark plug 13 Cylinder cov ...
-
Jonsered GC2236 - page 6
GENERAL SAFETY PRECA UTIONS 6 – English Impor tant P ersonal pr otective equipment HELMET A protectiv e helmet where there is a risk of falling objects HEARING PRO TECTION Wear hearing protection that provides adequate noise reduction. EYE PRO TECTION Alwa ys wear approv ed ey e protection. If you use a visor then you must also w ear approv ed pr ...
-
Jonsered GC2236 - page 7
GENERAL SAFETY PRECA UTIONS English – 7 BOO TS Wear boots with steel toe-caps and non-slip sole . CLO THING Wear clothes made of a strong f abr ic and av oid loose clothing that can catch on twigs and branches. Alwa ys wear heavy , long pants. Do not wear jewellery , shor ts sandals or go barefoot. Secure hair so it is abov e shoulder lev el. FIR ...
-
Jonsered GC2236 - page 8
GENERAL SAFETY PRECA UTIONS 8 – English be chec ked. See instructions under the heading Maintenance. Stop switc h Use the stop switch to s witch off the engine. Star t the engine and make sure the engine stops when you mov e the stop switch to the stop setting. Cutting attachment guar d This guard is intended to prev ent loose objects from being ...
-
Jonsered GC2236 - page 9
GENERAL SAFETY PRECA UTIONS English – 9 Muffler The muffler is designed to keep noise le vels to a minimum and to direct exhaust fumes a wa y from the user . A m uffler fitted with a catalytic conv er ter is also designed to reduce harmful exhaust gases. In countries that have a w arm and dr y climate there is a significant risk of fire. W ...
-
Jonsered GC2236 - page 10
GENERAL SAFETY PRECA UTIONS 10 – English Locking n ut A locking nut is used to secure some types of cutting attachment. When fitting, tighten the nut in the opposite direction to the direction of rotation of the cutting attachment. T o remov e it, undo the nut in the same direction as the cutting attachment rotates. (CAUTION! The nut has a left- ...
-
Jonsered GC2236 - page 11
GENERAL SAFETY PRECA UTIONS English – 11 General rules Only use cutting attachments with the guards we recommend! See the chapter on T echnical data. K eep the teeth of the blade correctly sharpened! Follow our instructions and use the recommended file gauge. An incorrectly sharpened or damaged blade increases the risk of accidents. Check the cu ...
-
Jonsered GC2236 - page 12
ASSEMBL Y 12 – English Fitting the J-handle • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. • Slide the spacer into the slot in the loop handle. • Fit the nut, knob and screw . Do not overtighten. • Attach the J-handle to the loop handle using the three screws, as sho wn. ? ...
-
Jonsered GC2236 - page 13
ASSEMBL Y English – 13 Fitting the guard e xtension CA UTION! The guard extension shall alwa ys be fitted when using the trimmer head/plastic blades and combination guard. The guard e xtension shall alwa ys be remov ed when using the grass b lade and combination guard. Enter the guard extension guide in the slot of the combination guard. Then cl ...
-
Jonsered GC2236 - page 14
ASSEMBL Y 14 – English Fitting other guards and cutting attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades . CA UTION! Ensure that the guard e xtension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft an ...
-
Jonsered GC2236 - page 15
FUEL HANDLING English – 15 Fuel safety Nev er star t the machine: 1 If you ha ve spilt fuel on it. Wipe off the spillage and allow remaining fuel to e vapor ate. 2 If you ha ve spilt fuel on y ourself or your clothes, change your clothes. W ash any part of your body that has come in contact with fuel. Use soap and water. 3 If the machine is leaki ...
-
Jonsered GC2236 - page 16
FUEL HANDLING 16 – English Mixing • Alwa ys mix the petrol and oil in a clean container intended for fuel. • Alwa ys star t by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of petrol. • Mix (shake) the fuel mixture thoroughly bef ore filling the ...
-
Jonsered GC2236 - page 17
ST AR TING AND ST OPPING English – 17 Check bef ore star ting • Check the b lade to ensure that no cracks ha ve f or med at the bottom of the teeth or by the centre hole. The most common reason why cr acks are f ormed is that sharp cor ners have been f or med at the bottom of the teeth while sharpening or that the blade has been used with dull ...
-
Jonsered GC2236 - page 18
ST AR TING AND ST OPPING 18 – English Choke: Set the choke control in the chok e position. Hold the body of the machine on the ground using your left hand (CA UTION! Not with your f oot!). Grip the starter handle, slowly pull out the cord with y our right hand until you f eel some resistance (the starter pawls grip), now quickly and pow erfully p ...
-
Jonsered GC2236 - page 19
W ORKING TECHNIQUES English – 19 General working instructions Basic safety rules 1 Look around you: • T o ensure that people, animals or other things cannot affect y our control of the machine. • T o ensure that people, animals, etc., do not come into contact with the cutting attachment or loose objects that are thrown out by the cutting atta ...
-
Jonsered GC2236 - page 20
W ORKING TECHNIQUES 20 – English Basic working tec hniques Alwa ys slow the engine to idle speed after each working operation. Long periods at full throttle without any load on the engine can lead to serious engine damage. Grass clearing using a grass b lade • Grass blades and g rass cutters must not be used on woody stems. • A grass b lade i ...
-
Jonsered GC2236 - page 21
W ORKING TECHNIQUES English – 21 Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower . K eep the cord parallel to the ground when cutting. Av oid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. • Do not allow the trimmer head to constantly come into ...
-
Jonsered GC2236 - page 22
MAINTENANCE 22 – English Carburettor Y our Jonsered product has been designed and manuf actured to specifications that reduce harmful exhaust fumes . The engine will be run in after it has used 8-10 tanks of fuel. T o ensure that the engine r uns at peak performance and produces as little harmful exhaust fumes as possible after the running-in pe ...
-
Jonsered GC2236 - page 23
MAINTENANCE English – 23 Low speed jet L T r y to find the highest idle speed by turning the low speed jet L clockwise then anti-cloc kwise. When the highest speed has been found, turn the low speed jet L 1/4 turn anti-clockwise. CA UTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned an ...
-
Jonsered GC2236 - page 24
MAINTENANCE 24 – English Muffler CA UTION! Some mufflers are fitted with a catalytic conv er ter . See chapter on T echnical data to see whether your machine is fitted with a catalytic con verter. The muffler is designed to reduce the noise le vel and to direct the exhaust gases a wa y from the operator . The exhaust gases are hot and can co ...
-
Jonsered GC2236 - page 25
MAINTENANCE English – 25 Air filter The air filter must be regularly cleaned to remove dust and dir t in order to av oid: • Carburettor malfunctions • Star ting problems • Loss of engine power • Unnecessary wear to engine par ts. • Excessive fuel consumption. Clean the filter ev er y 25 hours, or more regularly if conditions are exce ...
-
Jonsered GC2236 - page 26
26 – English MAINTENANCE Maintenance schedule The follo wing is a list of the maintenance that must be perf ormed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work descr ibed in this Operator’ s Manual. More extensive w ork must be carried out by an authoris ...
-
Jonsered GC2236 - page 27
English – 27 TECHNICAL D A T A T echnical data Note 1: Noise emissions in the environment measured as sound po wer (L W A ) in conformity with EC directive 2000/14/ EC. Note 2: Equivalent sound pressure le vel is calculated as the time-weighted energy total f or sound pressure lev els under various working conditions with the follo wing time dist ...
-
Jonsered GC2236 - page 28
28 – English TECHNICAL D A T A EC-declaration of conf ormity (Applies to Eur ope only) W e, Jonsered, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare that the clearing sa ws Jonsered GC 2236 with serial numbers dating from 2006 onwards (the year is clearly stated on the rating plate , follo wed by the serial number), comply with the requ ...
-
Jonsered GC2236 - page 29
1 Poly T rim 2 3 4 5 6 7 8 <20mm >20mm ! B A 6 Nm X 10 ...
-
Jonsered GC2236 - page 30
"Clic" 1 2 3 5 6 7 10 11 8,5 m 28' 4 8 4,2 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm S35 ...
-
Jonsered GC2236 - page 31
1 2 4 3 2,4-2,7 mm .095-.106" 4,25 m 14' 4,25 m 14' B 6" 15 cm A 6" 15 cm S35 5 ...
-
Jonsered GC2236 - page 32
T ap n’ Go 35 Spin "Clic" 1 2 3 5 6 7 9 8,5 m 28' 4 8 4,3 m 14' 2,4-2,7 mm .095-.106" 10 cm 4" 6" 15 cm ...
-
Jonsered GC2236 - page 33
"Clic" 1 2 3 5 6 7 9 10 m 32' 4 8 4,3 m 14' 2,7-3,3 mm .106-.13" 10 cm 4" 6" 15 cm T ap n’Go 45 Spin ...
-
Jonsered GC2236 - page 34
...
-
Jonsered GC2236 - page 35
...
-
Jonsered GC2236 - page 36
1151216-26 ´®z+S5^¶64¨ ´®z+S5^¶64¨ 2008-05-30 ...
¿Tienes una pregunta acerca de Jonsered GC2236?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Jonsered GC2236, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Jonsered GC2236 probablemente compartirá una forma de solucionarlo.