-
Viper 500.4 - page 1
models 200.4 500.4 ...
-
Viper 500.4 - page 2
2 © 2002 Directed Electronics, Inc ...
-
Viper 500.4 - page 3
3 © 2002 Directed Electronics, Inc T ABLE OF CONTENTS CONGRA TULA TIONS Congratulations for choosing a Viper Audio power amplifier from Directed Electronics, the industr y leader in high quality automotive security and audio equipment since 1990. With the introduction of Viper Audio power amplifiers, Directed Electronics continues to set new stand ...
-
Viper 500.4 - page 4
LIMITED TWO-YEAR CONSUMER W ARRANTY 4 © 2002 Directed Electronics, Inc Directed Electronics, Inc. promises to the original purchaser , to replace this product should it prove to be defective in workman- ship or material under normal use, for a period of two years from the date of purchase by the dealer as indicated by the date code marking of the ...
-
Viper 500.4 - page 5
5 © 2002 Directed Electronics, Inc High-powered car audio systems may produce sound pressure levels that exceed the threshold at which hearing loss may result. They may also impair a driver’ s ability to hear traffic sounds or emergency vehi- cles. Use common sense and practice safe listening habits when listening to or adjusting your audio syst ...
-
Viper 500.4 - page 6
6 © 2002 Directed Electronics, Inc INST ALLA TION GUIDELINES 1. Please read this owner’ s manual carefully before installing this ampli- fier . 2. Disconnect the batter y ground terminal prior to making any elec- trical connections. 3. Check for any hazards or obstruc- tions such as gas tanks, fuel or brake lines, and wiring harnesses before mou ...
-
Viper 500.4 - page 7
7 © 2002 Directed Electronics, Inc speaker load, the more heat is generated. For low impedance speaker applications or restricted ventilation installations, an external cooling fan may be advisable. 9. Batter y and ground connections to the vehicle should be made with crimped ring terminals of the appro- priate size (surface area is what counts); ...
-
Viper 500.4 - page 8
8 © 2002 Directed Electronics, Inc 1. S S p p e e a a k k e e r r O O u u t t T T e e r r m m i i n n a a l l s s - Connect the speakers to these terminals. (Refer to the Speaker Connection section of this guide.) 2. R R e e m m o o t t e e T T u u r r n n O O n n - This terminal turns on the amplifier when (+) 12 volt is applied to it. Connect it ...
-
Viper 500.4 - page 9
9 © 2002 Directed Electronics, Inc FIGURE 2—AMPLIFIER CONNECTIONS 500.4 REAR FIGURE 3—AMPLIFIER CONNECTIONS 200.4 REAR 1 2 4 3 5 4. ( ( + + ) ) 1 1 2 2 V V o o l l t t P P o o w w e e r r - Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of the vehicle batter y or the positive terminal of an isolated audio syst ...
-
Viper 500.4 - page 10
10 © 2002 Directed Electronics, Inc TOP P ANEL CONTROLS FIGURE 4—AMPLIFIER CONTROLS TOP 4 1. I I n n p p u u t t G G a a i i n n A A d d j j u u s s t t m m e e n n t t - Controls amplifier sensitivity and is used to match the input level of the ampli- fier to the output level of the signal source. 2. C C r r o o s s s s o o v v e e r r S S e e ...
-
Viper 500.4 - page 11
11 © 2002 Directed Electronics, Inc Control Panel Cover The amplifier’ s gain and filter controls are mounted under the elliptical control panel cover . Magnets hold the cover snugly and allow easy access. T T o o i i n n s s t t a a l l l l t t h h e e c c o o v v e e r r - Place the straight end of the control panel cover into the notched ...
-
Viper 500.4 - page 12
SPEAKER WIRING DIAGRAMS 12 © 2002 Directed Electronics, Inc Stereo Operation (bottom view four channel shown) Bridged operation (bottom view two channel shown) N N O O T T E E : : For bridged two-channel operation as shown below , connect the right channel RCA cables to the Front inputs of the amplifier , and left channel RCA cables to the rear in ...
-
Viper 500.4 - page 13
13 © 2002 Directed Electronics, Inc Simultaneous stereo/mono operation (bottom view) ...
-
Viper 500.4 - page 14
14 © 2002 Directed Electronics, Inc CROSSOVER SETTINGS AND GAIN ADJUSTMENT Y our Viper Audio power amplifier needs to be adjusted carefully to achieve maximum performance. These are some guidelines to follow when fine-tuning the amplifier . For full-range and simultaneous stereo/mono bass applications, the crossover selection switch should be ...
-
Viper 500.4 - page 15
SPECIFICA TIONS 15 © 2002 Directed Electronics, Inc RMS continuous power per channel, All channels driven into 4 ohms from 20 to 20,000 Hz, with less than 0.08% T otal Har monic Distortion @ 14.4 VDC C RMS continuous power per channel , All channels driven into 2 ohms from 20 to 20,000 Hz, with less than 0.1% T otal Har monic Distortion @ 14.4 VDC ...
-
Viper 500.4 - page 16
The company behind this system is Directed Electronics, Inc. Since its inception, Directed has had one purpose, to provide customers with the finest vehicle security , car stereo products, rear seat entertainment, and accessories available. The recipient of more than 20 patents in the field of advanced electronic technology , Directed is ISO 900 1 ...
¿Tienes una pregunta acerca de Viper 500.4?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Viper 500.4, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Viper 500.4 probablemente compartirá una forma de solucionarlo.