-
Cisco Systems ONS 15600 - page 1
CH A P T E R 11-1 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 11 Change Card Settings This chapter e xplains ho w to change transmi ssion settings on cards in a Cisco ONS 15600. Before You Begin As necessary , complete th e “NTP-E57 Document Existing Pro visioning” pr ocedure on page 7-2 . Before performing the follo wing pr ocedures, i ...
-
Cisco Systems ONS 15600 - page 2
11-2 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E157 Provision a Multir ate PPM NTP-E157 Provision a Multirate PPM Step 1 Complete the “DLP-E26 Log into CTC ” task on page 16 -39 to log into an ONS 15600 on th e network. Step 2 Click the Alarms tab: a. V erify that the alarm f ilter is not turned on. ...
-
Cisco Systems ONS 15600 - page 3
11-3 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E151 Provision an Optical Line Rate NTP-E151 Provision an Optical Line Rate Step 1 Complete the “DLP-E26 Log into CTC ” task on page 16 -39 to log into an ONS 15600 on th e network. Step 2 Click the Alarms tab: a. V erify that the alarm f ilter is not t ...
-
Cisco Systems ONS 15600 - page 4
11-4 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E150 Change th e Optical Line Rate Step 9 Click OK . The row on the Pluggable Ports pane turns light blue until the actual SFP is installed and then the row tu rns white. Stop. Y ou hav e completed this procedur e. NTP-E150 Change the Optical Line Rate Step ...
-
Cisco Systems ONS 15600 - page 5
11-5 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E149 Delete Pluggable Port Modules NTP-E149 Delete Pluggable Port Modules Step 1 Complete the “DLP-E26 Log into CTC ” task on page 16 -39 to log into an ONS 15600 on th e network. Step 2 Click the Alarms tab: a. V erify that the alarm f ilter is not tur ...
-
Cisco Systems ONS 15600 - page 6
11-6 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E66 Modify Line and Status T hresholds for Optical Ports Note If you need to remo ve the SFP , see the “DLP-E216 Remo ve an SFP” procedure o n page 18-15 . If you need to remo ve the 4PIO, see the “DLP-E217 Remov e a 4PIO Module” procedure on page 1 ...
-
Cisco Systems ONS 15600 - page 7
11-7 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E66 Modi fy Line and Status Thresholds for Optical Ports SD BER Sets the signal de grade bit error rate • 1E-5 • 1E-6 • 1E-7 (default) • 1E-8 • 1E-9 Provides Sync Indicates th at the port has been provisio ned as a network element timing reference ...
-
Cisco Systems ONS 15600 - page 8
11-8 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E66 Modify Line and Status T hresholds for Optical Ports Step 6 Click A pply . Service State Identif ies the autonomously generated state that gi ves the ov erall condition of the port. Service states appear in the format: Primar y State-Primary St ate Qual ...
-
Cisco Systems ONS 15600 - page 9
11-9 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E66 Modi fy Line and Status Thresholds for Optical Ports Step 7 Click the Thresholds su btab . The def ault selection is Near End, 15 Min, and Line ( Fi gure 11-1 ). Figure 1 1 -1 Pro visioning Thresholds for the OC-48 Card Step 8 As needed, c omplete th e ...
-
Cisco Systems ONS 15600 - page 10
11-10 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E66 Modify Line and Status T hresholds for Optical Ports T able 1 1 -3 OC-N Thr eshold Opti ons (Line, Section, and P ath) Heading Description Options Port Port number 1 – 16 for an OC-48 car d, 1 – 4 for an OC-192 card CV Coding violat ions Numeric. D ...
-
Cisco Systems ONS 15600 - page 11
11-11 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E66 Modi fy Line and Status Thresholds for Optical Ports Step 9 As needed, c omplete th e following: a. Click Phys ical to provision th e physical options in T able 11-4 for each OC-N port. b. Change the se lection to 15 Min or 1 Day as nec essary . c. Cli ...
-
Cisco Systems ONS 15600 - page 12
11-12 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E105 Change an Optical Port to SDH Step 10 Click A pply . Note See Chapter 7, “Man age Alarms, ” for information about the Alarm Beha vior tab, includ ing alarm prof iles and alarm suppression. Stop. Y ou hav e completed this procedur e. NTP-E105 Chang ...
-
Cisco Systems ONS 15600 - page 13
11-13 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E125 Change Card Service State Step 6 Y ou can re peat Steps 4 and 5 for any other ports on that card. Stop. Y ou hav e completed this procedur e. NTP-E125 Change Card Service State Step 1 Complete the “DLP-E26 Log into CTC ” task on page 16 -39 at the ...
-
Cisco Systems ONS 15600 - page 14
11-14 Cisco ONS 15600 Procedure Guide, R5.0 February 2008 Chapter 11 Change Card Settings NTP-E125 Change Ca rd Se rvice State Stop. Y ou hav e completed this procedur e. OOS,MT OOS-A U,AINS & UEQ (Out-of-Service and Au tonomous,Au to In-Service and U nequipped) OOS-A UMA,MT & UEQ (Out-of-Service and Autonomous Management,Maintenance and Un ...
¿Tienes una pregunta acerca de Cisco Systems ONS 15600?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Cisco Systems ONS 15600, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Cisco Systems ONS 15600 probablemente compartirá una forma de solucionarlo.