-
Autostart AS-2272 - page 1
Notice The manufactur er will accept no responsibility fo r any electrica l damage resulting from improper in stallation of the product, b e that either damage to the vehicl e itself or to t he unit. This uni t must be installed by a certified tech nician using a ll safety devices s up plied . Please note that this guide has been written for proper ...
-
Autostart AS-2272 - page 2
P. 2 Installation Guide Table of Contents Introducti on ............................................................ 2 Included in the Kit .................................................. 3 Installati on Tools .................................................... 3 Installation Points to Reme mber .......................... 3 Installatio n Order . ...
-
Autostart AS-2272 - page 3
Installation Guide P. 3 Included in the Kit Before beginning the installation, pleas e review the Installation Guide —particularly the Wiring Diagram and the Programming Options. Note: It is very important t hat you familiariz e yourself with the pro gramming and o peration of the system, even if you have already inst alled a similar system in t ...
-
Autostart AS-2272 - page 4
P. 4 Installation Guide ♦ When wiring in parall el, make sure to isolate each c onnection with a diode in order to avoid feed back and pos sible damage. Examples: Wiring a clutch bypass and a transponder module to the ground out when running wire: At the junctio n point, where Ground Out when running “splits” and goes to each dev ice, a diode ...
-
Autostart AS-2272 - page 5
Installation Guide P. 5 Installation Order The following is a suggested order for the Installation pr ocedure. It is intended as a guide f or novices, to hel p make the pr ocess of insta lling a remote s tarter module eas ier. Time is wasted by rewiring the module whe n mistakes are mad e. Also, the nea tness of t he installation is lessened every ...
-
Autostart AS-2272 - page 6
P. 6 Installation Guide when the module i s in the vehicl e. The fuses on t he power wires shou ld be removed d uring the pre-wire stage. The fus es will not be put back in unt il the powerin g stage of the i nstallation. − Once the pre-wiring is finis hed, the module c an be brought int o the vehicle. Be fore the module i s mounted, connect the ...
-
Autostart AS-2272 - page 7
Installation Guide P. 7 A basic introduction to the Relay What is a relay? A device that responds to a small current or v oltage change by activating sw itches or other devices in an electric circ uit. An electroma gnetic switch, remot e-controlled switc h, a switc hing device. Why are Relays used? Relays can have sev eral purposes in remote car st ...
-
Autostart AS-2272 - page 8
P. 8 Installation Guide quenching/sup pression diode, and t hat the Negative trigg er is on the same terminal of the relay as the Anode (+ or no n-striped side) of the quenchin g/ suppression diode. When a relay’s coil is energiz ed, a magnetic fie ld is created and e nergy is stored in the coil . When power is removed from the coil, the magnetic ...
-
Autostart AS-2272 - page 9
Installation Guide P. 9 Problem: Some vehicle circuits nee d to be isolate d from feedback . In some cas es, when a vehicl e is remote started , feedback oc curs on a circu it and powers anot her device or sw itch that was not intended to be p owered during t he remote starts. The following example will b e a Positive (+) Parking Light circ uit tha ...
-
Autostart AS-2272 - page 10
P. 10 Installation Guide the relay is act ivated, +12 vol ts from 87 is sent t hrough 30, and t he OEM trunk sw itch is activated, by the positiv e pulse. Interruption: Example : Creating a St arter Kill relay to prevent unauthoriz ed starting of the vehicle. Problem : The OEM starter circ uit needs to be disabled only when theft is attempted. Solu ...
-
Autostart AS-2272 - page 11
Installation Guide P. 11 module's Trunk rel ease output activa tes the relay. The ground sign al is sent from 87 through 30 t o the vehicle's Trunk release wire ac tivating the switc h and opening the trunk. Harness Description 6-pin Mai n Ignition Ha rness (a.k.a . The Primary ha rness) The two Red wires are the power i nputs for the mod ...
-
Autostart AS-2272 - page 12
P. 12 Installation Guide 5-pin Secondary Ha rness (a.k.a. the secondary harn ess) This harness has the remaining wires used in basic remote s tarter inst allations, pos itive parking light output, the safety shut down in puts, and the ground wire for the module. Wire Description 1 BLACK (–) Chassis ground input This wire must be connected to bare ...
-
Autostart AS-2272 - page 13
Installation Guide P. 13 6 VIOLET (+) Door pin input This input should be used in vehicles that use a posi tive-switching Dome Light circuit. Connect to a Door trigger wire testing +12 V with a Door open. CAUTION! You can only use a negative or a positive c onnection. In other wor ds, only the NEGATIVE DOOR INPUT or the POSITI VE DOOR INPUT wire is ...
-
Autostart AS-2272 - page 14
P. 14 Installation Guide If no Glow-plug wire is found on the vehicle, the Glow-plug input on t he module may be “timed out”. The module will power up the Igni tion and Glow -plug circui ts and simply wait for the time-out before starting. Keeping the Glow-plug input wire of the module unconnecte d will hold the ignition ON for the preprogramme ...
-
Autostart AS-2272 - page 15
Installation Guide P. 15 Note: To exit programming mode, close the hood. Note: To exit programming mode, press on the antenna button once (the LED will come ON ) and release. Remember: You can use the prog ramming Assistance butto n instead of the hood pin at any time the hood is up. The Programming Assistance Button (a.k.a. PAB) The PAB is located ...
-
Autostart AS-2272 - page 16
P. 16 Installation Guide To install this unit in a vehicle with an a utomatic transmission: 1. Cut the loop on the pc board ( Yellow wire). 2. Make sure the Black/White handbrake wire is not conn ected to any of the vehicl e circuits. 3. Make all the r egular connec tions. 4. Power up the unit . The parking l ights will flash 4 times . 5. When lear ...
-
Autostart AS-2272 - page 17
Installation Guide P. 17 FEATURE 4 – Door lock pulse timing OPTION 1* 7/10-sec. lock / un lock pulses OPTION 2 4-sec. lock / unlock pulses OPTION 3 7/10-sec. lock pulse and two 1/4-sec. unlock pulses FEATURE 5 – LED flashing OPTION 1* ENABLED (without s tarter kill Æ will flash o nly when ig nition is OFF ) OPTION 2 DISABLED OPTION 3 ENABLED ( ...
-
Autostart AS-2272 - page 18
P. 18 Installation Guide 3. Press the Ι butt on if you wish to increase t he time del ay or the ΙΙ but ton if you want to decrease it. The time del ay will be increase d or decreased by 50ms. and the p arking lights will f lash once every time th e Ι or ΙΙ button is pressed. 4. Press the Ι and ΙΙ buttons to gether to sav e the settings you ...
-
Autostart AS-2272 - page 19
Installation Guid e P. 19 Clutch Bypass In order to rem ote start a manual transm ission vehicl e, the clutch swi tch must be bypasse d. Clutch safety switch c ircuits can take many forms. Lis ted below are th e most comm on ones. Some vehicles may also have a separate or c ombined switch on the cl utch pedal for cruis e control. Usually a cruise c ...
-
Autostart AS-2272 - page 20
P. 20 Installation Guide modules connecte d to the G.O. Wire, a relay (and d iodes) may have to be add ed to strengthen t he negative current going to the clutc h bypass. Positive: Very similar to the n egative system, e xcept that the ve hicle's clut ch relay is trigge red by 12 volts instead of a negative signal. In a Positive system, when t ...
-
Autostart AS-2272 - page 21
Installation Guid e P. 21 Starter Kill Arming Mode Note: It can only be activated if b utton Ι is programmed as LOCK or UNLOCK button. The Starter Kill (if installed) ca n be configure d by the in staller either to Passive Mode (so as to arm automatically) or Active Mode (so as to require the user’s interv ention for armin g). By default, t he R ...
-
Autostart AS-2272 - page 22
P. 22 Installation Guide Bypass Remote starters of this series offer three possibilities for bypass D2D: they are compatib le with Trilogix, ADS and Fortin bypasses ( Trilogix by de fault ). Engine Run Ti me On a gas engin e, the Remote Car Starter can be programmed to r un the eng ine for 3, 15, or 25 minutes (15 minut es by default ). On a diesel ...
-
Autostart AS-2272 - page 23
Installation Guid e P. 23 To enter Cold Weather Mode: • Press and hold the ΙΙ button for 3 seconds or until the park ing lights flas h three (3) times. To exit Cold Weather Mode, do an y one of the following actions: • Open the hood. • Start the engine b y remote. • Start the engine wi th the key. • Press and hold the ΙΙ button for th ...
-
Autostart AS-2272 - page 24
P. 24 Installation Guide c. Press the push button s witch until t he Parking lights flash twice . d. Release the pus h button and turn the ignit ion to the OF F position. The LED on the antenna will flash quickly to indicate that the vehicle is now out of Valet mode. Panic Mode Note: Panic mode can only be activate d if the horn op tion has been a ...
-
Autostart AS-2272 - page 25
Installation Guid e P. 25 transmitter. The parking lights will fl ash 3 times quickly and remain lit. 4. Remove the key: the engi ne will continue running. 5. Exit the vehicle and close all doors, hood and trunk. 6. Press for approx. 1 second either button: Ι or ΙΙ . Note: The vehicle will a lso enter Ready Mode once the engine run time ex pires ...
-
Autostart AS-2272 - page 26
P. 26 Installation Guide OEM alarm control. Mak e sure the mod ule is able to arm and disar m the oem alar m (if applicable). Door locks and trunk testing. Make sure each of th ese options res pond to the transmitter (if ins talled). Starter kill option. Sit ins ide the veh icle with all doors closed. Arm th e vehicle, t hen try to star ...
-
Autostart AS-2272 - page 27
Installation Guid e P. 27 Diagnostics – Parking Light Flash Table Flashes Description 1 • Doors locked, starter kill armed • Run time has expired • Ι & ΙΙ buttons pressed • Start signal received by the module • Cold weather mode cancelled 2 slow flashes followed by 8 quick flashes • Reset from manual to automatic 2 • Doors un ...
-
Autostart AS-2272 - page 28
P. 28 Installation Guide Troubleshooting Q & A The following ar e some common ins tallation-relate d issues. A problem or symptom is given and then possible solut ions and/or sugge stions as to areas to verify are enumerated. 1. I cannot program the remote control. • Do the parking lights come on when y ou open the hoo d? (Does the hood pin w ...
-
Autostart AS-2272 - page 29
Installation Guid e P. 29 • Do you have the co rrect OEM disarm wire? • Did you program t he disarm wire? 11. The ABS and the CHECK ENGINE light come on in the dash. • Are you missing a second ignit ion or access ory? 12. The car starts and runs but t he heater blower motor does n ot work. • Incorrect accessory wire . • Does it have more ...
-
Autostart AS-2272 - page 30
P. 30 Installation Guide 25. I blow fuses ever y time I try the remote door loc ks and I have alr eady installed a r elay. • Door locks are reverse p olarity, and not positive trigger. 26. I blow fuses every time I try the remote trunk rel ease and I have already installed a relay. • Trunk release is rev erse polarity, and not positive trig ger ...
¿Tienes una pregunta acerca de Autostart AS-2272?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Autostart AS-2272, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Autostart AS-2272 probablemente compartirá una forma de solucionarlo.