-
Makita DA4030 - page 1
INSTR UCTION MANU AL WA R N I N G : F or your pers onal safety , READ and UNDE RST AND before using. SA VE THESE INSTR UCTIONS FOR FUTURE REFE RENCE. www .makitatoo ls.com Angle Drill 13 mm (1/2”) MODEL D A4030 13 mm (1/2”) MODEL D A4031 003008 DOUBLE INSULA TION ...
-
Makita DA4030 - page 2
2 SPECIFICATIONS * Extended sp ade grip • Manufacturer reser ves the ri ght to chan ge specifi cations w ithout noti ce. • Specificat ions may differ from countr y to count r y . GENERAL SAFET Y RUL ES USA002-2 (F or All T ools ) W ARNING: Read and under stand all instruc tions. F ailure to f ollow all instructions listed below , ma y result in ...
-
Makita DA4030 - page 3
3 Electrical Safety 4. Double insulated tools are equipped with a polarized plug (one b lade is wider than the other .) This plug will fit in a polarized outlet only one wa y . If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified elec- trician to install a polarized outlet. Do not c h a n g e ...
-
Makita DA4030 - page 4
4 21. Check f or misalignment or binding of moving pa r ts, breakage of parts, and an y other condition that may aff ect the tools operation. If damaged, ha ve the tool ser- viced before using. M any accidents are caused by poorly maintai ned tools. 22. Use only accessories that are recom- mended b y the manufacturer fo r your model. Accessories th ...
-
Makita DA4030 - page 5
5 5. Do not lea ve the tool running. Ope rate the tool only when hand-held. 6. Do not touch the drill bit or the w orkpiece immediately a fter operation; they ma y be extremel y hot and could burn your skin. 7. Some material contains chemicals whic h may be to xic. T ake caution to prevent dust inhalation and skin contact. Follo w mate- rial suppli ...
-
Makita DA4030 - page 6
6 SYMBOLS USD201-2 The followings show the symbols used for tool. V ....................... v olts A ....................... amp eres Hz ..................... hertz ................ alternating current .................... no load speed .................... Class II Construction .../min ................ rev olutions or reciprocati on per minute n ? ...
-
Makita DA4030 - page 7
7 FUNCTIONAL DESCRIPTION CA UTION : • Alwa ys be sure that the to ol is switche d off and unplugged before adjusting or checking funct ion on the tool. Switch action CA UTION: • Before pluggi ng in the t ool, always check to see that the s witch trigger act uates properly and r eturns to the “OFF” position whe n released . T o start the too ...
-
Makita DA4030 - page 8
8 change knob positioned half wa y between the position 1 and the posit ion 2, the t ool may be damaged. T orque limiter For Model DA4031 only The torque limite r will actuate when a c er tain torque le vel is reached (f or lower spe ed setting: positio n 1). The motor will disengage fr om the output sh aft. When thi s happens, the bit will stop tu ...
-
Makita DA4030 - page 9
9 Spade grip The spade gr ip can be inst alled in any posit ion as shown in the figure . T o change the posi tion, loosen the he x bolts (both sides) with a hex wrench and tur n the spad e grip to the desired position. T hen tighten the he x bolts securely . Afte r reposition the grip , re tur n the hex wrench to th e wrench holder . CA UTION: • ...
-
Makita DA4030 - page 10
10 OPERA TION Holding tool CA UTION: • This i s a powerful tool. Hig h torque is developed and it is impor t ant that the too l should be secu rely held and proper ly braced. Grasp the switch handle with on e hand and th e spade grip with the other ha nd. When drilling a large hole with a s elf- feed bit, etc., the side gr ip (aux iliar y ha ndle ...
-
Makita DA4030 - page 11
11 • T h e r ei sat r e m e n d o u st w i s t i n gf o r c ee x e r t e do nt h et o o l / bit at the time of hole break through. Hold t he tool fir mly and ex er t c are when the bi t begins to b reak thro ugh the workpie ce. • A stuck bi t can be remov ed simply b y setting the re versin g switch to re ver se rotation in order to back ou t. ...
-
Makita DA4030 - page 12
12 A CCESSORI ES CA UT ION: • These ac cessor ies or attach ments are recommended for use with your Makita t ool specifie d in this manual. T he use of any other acces sori es or attachm ents might present a r isk of inju r y to persons. Only u se accessor y or attach ment for its stated pur pose. If you need any assistance for more deta ils rega ...
-
Makita DA4030 - page 13
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...
-
Makita DA4030 - page 14
14 1. This pr oduct was purchased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...
-
Makita DA4030 - page 15
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Chris ...
-
Makita DA4030 - page 16
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and ot ...
¿Tienes una pregunta acerca de Makita DA4030?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita DA4030, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita DA4030 probablemente compartirá una forma de solucionarlo.