-
Esoteric AZ-1 - page 1
D00905700B Digital Pre Main Amplifier Owner ’ s Manual ...
-
Esoteric AZ-1 - page 2
2 IMPOR T ANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sou ...
-
Esoteric AZ-1 - page 3
3 CAUTION < DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS ARE WITHIN! < IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT, CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE PRODUCT UNTIL IT HAS BEEN REPAIRED. W ARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN ...
-
Esoteric AZ-1 - page 4
4 What’ s in the box Please confirm that the following accessories are in the box when you open it. Remote control unit (RC-1056) x 1 Batteries (AA, R6, SUM-3) x 2 Felt sheet x 4 Power cord x 1 Owner’s manual x 1 Warranty card x 1 Before Use Read this before operation < As the unit may become warm during operation, always leave sufficient sp ...
-
Esoteric AZ-1 - page 5
5 Speaker Connections CAUTION: < Switch off the power to all equipment before making connections. < Read the instructions of each component you intend to use with this unit. < Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the signal interconnection cables together with the AC power cord or speaker cables. N ...
-
Esoteric AZ-1 - page 6
When you are using two or three AZ-1 units for multi-channel listening, connect them as shown here. DIGIT AL OUT WORD SYNC IN AUDIO OUT D A B B E C 6 Connections i.LINK cable RCA coaxial cable optical digital cable BNC coaxial cable Turntable Supplied power cord Wall socket RCA cable Connect one of these cables. Master clock generator (G-0s, AZ-1, ...
-
Esoteric AZ-1 - page 7
7 Digital audio input terminals [DIGIT AL IN] Connect any one of these terminals to the digital output terminal of a digital device (SZ-1, UZ-1, etc.) using a commercially available cable. COAXIAL (RCA): Use RCA (pin) digital audio cable OPTICAL: Use optical digital audio cable (TOS) i.LINK (AUDIO): Use S400 compatible IEEE1394 6pin cable < The ...
-
Esoteric AZ-1 - page 8
8 i.LINK (IEEE 1394) i.LINK is also known as IEEE 1394, an international specification. This unit is ready to accept i.LINK (AUDIO). By connecting an i.LINK (AUDIO)-capable device to the IEEE 1394, or i.LINK (AUDIO) terminal on this unit using an i.LINK cable, you can transmit Super Audio CD multi-channel signals that could not be transmitted excep ...
-
Esoteric AZ-1 - page 9
9 Battery Replacement If the distance you can operate your remote decreases, the batteries are exhausted. In this case replace the batteries with new ones. Precautions concerning batteries < Be sure to insert the batteries with correct positive “ + ” and negative “ _ ” polarities. < Use batteries of the same type. Never use different ...
-
Esoteric AZ-1 - page 10
10 B A C D E G F ディスプレー Front Panel INPUT Turn this knob to select an input. In the setup mode, use this knob to change settings. STANDBY Use this button to turn the unit on and to standby. The indicator is red in the standby mode. It turns blue when the unit is turned on. SETUP Press this button to enter or exit the basic setup mode. P ...
-
Esoteric AZ-1 - page 11
11 B A D F E G C Understanding the remote contr ol unit Note: To simplify explanations, instructions in this manual refer to the names of the buttons and controls on the front panel only. Associated controls on the remote control will also operate similarly. ON/STANDBY Use the ON button to turn the unit on. Use the STANDBY button to turn it standby ...
-
Esoteric AZ-1 - page 12
12 4 3 2 standby indicator First of all, turn on the power of the connected components. 1 It may take several seconds for the unit to start outputting sounds. Wait until “WAIT ...” disappears from the display. Select an input by turning the INPUT knob. 3 The current input appears on the left of the display. Repeatedly turn the knob until the de ...
-
Esoteric AZ-1 - page 13
13 Muting To mute the sound temporarily, press the MUTING button. Press the MUTING button again to restore the sound. < While muting is engaged, “MUTING” and the name of the selected terminal alternately blink on the display. Display dimming The display on the main unit can be dimmed to suit the environment in which you listen to music. Ther ...
-
Esoteric AZ-1 - page 14
14 SETUP INPUT Basic Settings < If you leave the unit idle for 10 seconds, the setup mode will be cancelled. Repeatedly press the SETUP button to select the menu item to be changed. 1 Turn the INPUT knob to select the options within the menu item. 2 Repeatedly press the SETUP button (or leave the unit idle for 10 seconds) to exit the setup mode. ...
-
Esoteric AZ-1 - page 15
15 W_OUT (Wor d sync output frequency) Select the frequency of the word sync signal. The factory setting is “44.1”. 100 a q 44.1 a q 88.2 a q 176(176.4) a q 48 a q 96 a q 192 < The word sync signal is output only when the WORD button is set to “W`_OUT” (see page 14). CH (Channel) When the i.LINK (AUDIO) terminal is connected to a digital ...
-
Esoteric AZ-1 - page 16
16 Gain Setting for Analog Audio Input You can adjust the relative volume between the LINE IN terminals. Once the relative volume is set, each component connected to the AZ-1 will have the approximate same volume level. Select an input to be changed (LINE1, LINE2 or LINE3/PHONO) by turning the INPUT knob. Start with the component that has the lowes ...
-
Esoteric AZ-1 - page 17
17 SETUP INPUT The names of the inputs shown on the display can be changed. You can also set the INPUT knob to skip the input terminals that are not in use. For example, if a CD player is connected to the COAX1 terminal and a DVD player to the OPT1 terminal, you can change the name of COAX1 Example: When a CD player is connected to the COAX1 termin ...
-
Esoteric AZ-1 - page 18
18 T roubleshooting In case you experience any problem with this unit, please take the time to look through this chart and see if you can solve the problem yourself before you call your dealer. No power e Check the connection to the AC power supply. Check and make sure the AC source is not a switched outlet and that, if it is, the switch is turned ...
-
Esoteric AZ-1 - page 19
Specifications General Power supply Europe model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V, 50 Hz U.S.A./Canada model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 120 V, 60 Hz Korea model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
-
Esoteric AZ-1 - page 20
0706 . MA -1033B This appliance has a serial number located on the rear panel. Please record the model number and serial number and retain them for your records. Model number Serial number TEAC ESOTERIC COMPANY 3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan Phone: (0422) 52-5132 e-mail: eso-os@tec.teac.co.jp TEAC AMERICA, INC. 7733 Telegraph ...
¿Tienes una pregunta acerca de Esoteric AZ-1?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Esoteric AZ-1, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Esoteric AZ-1 probablemente compartirá una forma de solucionarlo.