-
John Deere ET-3504-J - page 1
1/2-Inch Drill Operator's Manual 1 CAUTION RISK OF INJURY! READ MANUAL BEFORE OPERATING! THIS MANUAL IS AN IMPORTANT PART OF THE DRILL AND SHOULD REMAIN WITH THIS UNIT WHEN YOU SELL OR RENT IT. ET -3504-J 1/2-INCH DRILL ...
-
John Deere ET-3504-J - page 2
2 1/2-Inch Drill Operator's Manual Congratulations on the purchase of your new drill! You can be assured your drill was constructed and designed with quality and performance in mind. Each component has been rigorously tested to ensure the highest level of acceptance. This operator's manual was compiled for your benefit. By reading and fol ...
-
John Deere ET-3504-J - page 3
1/2-Inch Drill Operator's Manual 3 T able of Content SAFETY .................................................................................................................. 4-9 GENERAL SAFETY RULES .................................................................. 4-9 FUNCTIONAL DESCRIPTION ................................................... ...
-
John Deere ET-3504-J - page 4
4 1/2-Inch Drill Operator's Manual W ARNI N G W A R N I NG SI N T HE M A NUA LS . W A RN I NG SI N T HE M A NUA LS . CA U T I ON OC A UT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O T H E M A N UA L S OC AUT I ON S IN O T H E M A N UA L S OC A UT I ON S IN O T H E M A N UA L S RECOGNIZE SAFETY INFORMATION This is the safety alert symbol. ...
-
John Deere ET-3504-J - page 5
1/2-Inch Drill Operator's Manual 5 KEEP WORK AREA CLEAN AND WELL LIT. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. Don't expose power tools to rain. Don't use power tools in damp or wet locations. Keep work area well lit. Don't use tool in presence of flammable liquids or gases. Power tools produc ...
-
John Deere ET-3504-J - page 6
6 1/2-Inch Drill Operator's Manual DON'T OVERREACH Keep proper footing and balance at all times. MAINTAIN TOOLS WITH CARE Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and replace if damaged, have repaired by authorized service fac ...
-
John Deere ET-3504-J - page 7
1/2-Inch Drill Operator's Manual 7 OUTDOOR USE EXTENSION CORDS When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT Watch what you are doing. Use common sense. Do not operate tool when you are tired. CHECK DAMAGED PARTS Before further use of the tool, a guard or other part that is damaged sho ...
-
John Deere ET-3504-J - page 8
8 1/2-Inch Drill Operator's Manual POLARIZED PLUGS To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to ins ...
-
John Deere ET-3504-J - page 9
1/2-Inch Drill Operator's Manual 9 EXTENSION CORD Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table shows the correct size to use dep ...
-
John Deere ET-3504-J - page 10
10 1/2-Inch Drill Operator's Manual PREPARATION PRIOR TO OPERATION: Before using the Electric Power Tool, complete the following preparations. 1. Extension cord: When the work area is far away from the power source, use an extension cord of sufficient thickness and rated capacity. The extension cord should be kept as short as possible. CAUTION ...
-
John Deere ET-3504-J - page 11
1/2-Inch Drill Operator's Manual 11 Operation APPLICATIONS: Drilling in various metal, lumber, and plastics. PRE-OPERATION: CAUTION: CONFIRM THE FOLLOWING POINTS PRIOR TO CONNECTING THE PLUG TO THE POWER RECEPTACLE. 1. Confirm the applied power source: Be sure to operate the Electric Power Tool in the voltage specified on the name plate. 2. Co ...
-
John Deere ET-3504-J - page 12
12 1/2-Inch Drill Operator's Manual OPERATION: 1. Pressing force of drill: You can not get holes quickly even if pressing it by strong force more than necessary. It not only damages the tip of the drill bits and decreases the efficiency of operation, but also shortens the life of the drill. 2. In case of penetrating holes: Drill bits are subje ...
-
John Deere ET-3504-J - page 13
1/2-Inch Drill Operator's Manual 13 Maintenance and Inspection MAINTENANCE AND INSPECTION: CAUTION: BE SURE TO SWITCH POWER OFF AND DISCONNECT THE PLUG DURING MAINTENANCE AND INSPECTION. 1. Inspecting the drill bit: Since use of an abraded drill bit will cause motor malfunctioning and degraded efficiency, replace the drill bit with a new one o ...
-
John Deere ET-3504-J - page 14
14 1/2-Inch Drill Operator's Manual Notes ...
-
John Deere ET-3504-J - page 15
1/2-Inch Drill Operator's Manual 15 Notes ...
-
John Deere ET-3504-J - page 16
16 1/2-Inch Drill Operator's Manual Manufactured for Deere & Company, Moline, Illinois 61265 1/2" Drill Operator's Manual 111 Code No. C99110561 N #37-0689-090403 © Copyright 2003. John Deere ...
¿Tienes una pregunta acerca de John Deere ET-3504-J?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con John Deere ET-3504-J, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con John Deere ET-3504-J probablemente compartirá una forma de solucionarlo.