-
Makita 1902 - page 1
INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com P o wer Planer MODEL 1902 002543 DOUBLE INSULA TION ...
-
Makita 1902 - page 2
2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA002-2 (F or All T ools ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic shoc k, fire and/or s ...
-
Makita 1902 - page 3
3 change the plug in any wa y . Double insula- tion eliminates the need for the three wire grounded pow er cord and grounded power supply system. 5. A void body contact with gr ounded sur- faces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. 6. Do not expose power tools to ...
-
Makita 1902 - page 4
4 model. Accessories that may be suitab le for one tool, may become hazardous when used on another tool. SER VICE 23. T ool ser vice mu st be performed only by qualified repair personnel. Service or main- tenance performed by unqualified personnel could result in a risk of injur y . 24. When servicing a tool, use only identical replacement parts. F ...
-
Makita 1902 - page 5
5 poor installation or a poorly balanced blade . 8. Make sure the blade is not contacting the workpiece bef ore the switch is turned on. 9. W ait until the blade attains full speed before cutting. 10. Keep at least 200 mm (8”) awa y from the tool at all times. 11 . Alwa ys switch off and wait for the blades to come to a complete stop before an y ...
-
Makita 1902 - page 6
6 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore adjusting or checking function on the tool. Adjusting depth of cut Depth of cut ma y be adjusted by simply turning the knob on the front of the tool. Switch action CA UTION: • Bef ore plugging in the tool, always chec k to see that the s wit ...
-
Makita 1902 - page 7
7 • Use only the Makita wrench provided to remo ve or install the blades . F ailure to do so may result in o ver tightening or insufficient tightening of the installation bolts. This could cause an injur y . 1. Remov e the existing b lade, if the tool has been in use, carefully clean the drum surfaces and the drum cov er . T o remov e the blades ...
-
Makita 1902 - page 8
8 clearances between the b lade ends and the tool body . 9. Check the three he x flange head bolts for final tightness . 10. Repeat procedures 1 - 9 f or other blade. For the correct planer blade setting Y our planing surf ace will end up rough and unev en, unless the blade is set properly and securely . The b lade must be mounted so that the cutti ...
-
Makita 1902 - page 9
9 The nozzle assembly ma y be attached after the chip cov er on the tool body is remov ed. When slipping on the assembly , fit the pin on it into the rear cov er hole. Use the chip cov er screws to f asten it in place. OPERA TION Planing operation First, rest the tool front base flat upon the workpiece surface without the blades making an y contact ...
-
Makita 1902 - page 10
10 Dra w a cutting line on the wor kpiece . Inser t the edge fence into the hole in the front of the tool. Align the blade edge with the cutting line. Adjust the edge f ence until it comes in contact with the side of the workpiece, then secure it b y tightening the screw . When planing, mov e the tool with the edge fence flush with the side of the ...
-
Makita 1902 - page 11
11 Chamfering T o make a chamfering cut as show n in the figure, align the “ V ” groov e in the front base with the edge of the workpiece and plane it. MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and unplugged bef ore attempting to perform inspection or maintenance. Replacing carbon brushes Remov e and check the carb ...
-
Makita 1902 - page 12
12 Use a screwdriv er to remove the brush holder caps. T ake out the worn carbon br ushes , inser t the new ones and secure the brush holder caps. T o maintain product SAFETY and RELIABILITY , repairs, any other maintenance or adjustment should be perf or med by Makita A uthor iz ed or F actor y Ser vice Centers , always using Makita replacement pa ...
-
Makita 1902 - page 13
13 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut ...
-
Makita 1902 - page 14
14 1. This product was purc hased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade ...
-
Makita 1902 - page 15
15 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ARIZONA 3707 E. Broadway Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 CALIFORNIA 41850 Christy St. Fremont, CA 94538-5107 (510) 657-9881 14930 Northam St. La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Av enue Sacramento , CA 95825 (916) 482-5197 7674 Clair ...
-
Makita 1902 - page 16
W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o ...
¿Tienes una pregunta acerca de Makita 1902?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita 1902, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita 1902 probablemente compartirá una forma de solucionarlo.