-
Airlink101 APO1200 - page 1
Wireless N/A 5GHz 200mW Out door AP Model: APO1200 Quick Inst allation Guide V .1.0 ...
-
Airlink101 APO1200 - page 2
1 1. Before Y ou St art 9 W e b Browser : Internet Explorer (7.0 or abo ve), Firefox, Safari 9 A Computer with a network adapter properly installed 9 2 x RJ-45 E t h er net c ab l e Front Panel Rear Panel 1. Reboot Button : Unscrew the screw and click Reset button to rest art system or rese t to defau l t configura tions. Î Press and hold the Rese ...
-
Airlink101 APO1200 - page 3
2 APO1200 is a multiple mode syste m which can be co nfigured either as a wireless gatewa y or an access poin t as desired. It also can be used as a WDS link for Ethernet netw ork expansion. This section depicts different applications on Router AP Mode , AP Mode , WDS Mode , CPE Mode , Client Bridge+Unive rsal Repeater Mode and CPE+AP Mode . A pp l ...
-
Airlink101 APO1200 - page 4
3 2. Hardware Inst allation 1. Connect N-type antenna to the N-type connector on the re ar panel 3. Connect the opposite end of the RJ-45 cable t o the P+DA T A O UT port on the Pow er over Ethernet Injector 4. Connect one end of another RJ-45 cable to the DA T A IN port on the Power over Ethernet Injecto r 2. Connect one end of a RJ-45 cable into ...
-
Airlink101 APO1200 - page 5
4 3. Configuring the Access Point Note : 1. It is recommended that you configure the Access Point from a wired computer . Before the Acc ess Point c an be configured, if you connect the AP to your computer directly , you must manually assign a static IP address to your computer's network adapter in the subnet of 192.16 8.2.x (Ref er to S ecti ...
-
Airlink101 APO1200 - page 6
5 Note : 1. T o protect your net work from any unauthorized acc ess it is recommended to enable wireless encryption. 2. The examples below are for WP A2-PSK. If you select WP A-PSK or WP A2-PSK, make sure your wireless adapters support WP A or WP A2. If your wireless adapters do not support WP A or WP A2, then select WEP . 5. Co nfigur e the LAN se ...
-
Airlink101 APO1200 - page 7
6 4. Configuring for WDS Link Note : 1. The s y s t e m prov ide WDS functi o n o n Router AP Mode , AP Mode and WDS Mode . 2. WD S Link requi res at least 2 A PO120 0. The T wo wir e netwo rks( LAN) ne ed the same subnet . 3. The WDS Link needs to be set at sa me Channel and with same Security Ty p e . 4. Please install and test in a lab environme ...
-
Airlink101 APO1200 - page 8
7 4. Click Enable and enter the Remote AP O1200's MA C Address . Setting Up the Remote APO1 200 (Remote Base S tation) 1. Copy dow n the 12 digit MAC Address of the Main APO1200 ( Main Ba se St ation ). The MAC Addr ess is on t h e devic e label or t he Ove r vie w Page ( St at us ->O ver vi ew ) and Wireless General Setup Page( Wireless -& ...
-
Airlink101 APO1200 - page 9
8 5. Configuring for Client Bride Note : 1. This section will walk you through the steps of sharing (bridging) an internet connection in one building, and extending tha t same i ntern et t o anothe r buildi ng. 2. The “ Main Base St ation ” provide Access Point w ith SSID “ Main_ AP ” 3. The T wo wire networks(LAN) need the same subnet . 4. ...
-
Airlink101 APO1200 - page 10
9 Setting Up the Client Bridge (Client S tation) 3. Click Site S urvey button. The system will automatica lly scan and display the scan results of all AP existing near by the system 4. Use Mai n_ AP as an example here where the AP is encr ypted via WP A2-PSK/ AES security type. Click Select butto n of the Mai n_A P , and then click Next button. 1. ...
-
Airlink101 APO1200 - page 11
10 Note : 1. T o verify wired network of Client S tation can access Main Base S tation, use ping c ommand to “192.168.2.254” 2. If you can not access Main Base S tation, verify the IP address of the wired client (PC or Laptop) is in the same subnet with Main Base S tation. 8. Click St a tus->Remote AP , the Connec tion Information should be ...
-
Airlink101 APO1200 - page 12
11 6. Configuring for Universal Wireless Repeater Note : 1. This section will walk you through the steps of sharing (bridging) an internet connection in one building, and extending tha t same i nter n et t o anothe r buildi ng wi th repe at Acc ess Po int. 2. A repe ater is just a very normal client which, at the sa me time , c an also be an access ...
-
Airlink101 APO1200 - page 13
12 Note : 1. The Chann el of Repeat AP should be the same with Main Base S tation. 2. T o verify wir eless client s can associate ESSID “Repeate r_Main_AP” with WEP key . 3. T o verif y wire less clients c an use pi ng com mand t o “192. 168. 2.254 ”. 4. If you can not access Main Base S tation, verify the IP address of the wireless client ...
-
Airlink101 APO1200 - page 14
13 7. How to configure TCP/IP settings on your PC Wind ows XP/2 000 1. Go into the Control Panel , double -clic k the Network Connec tions icon and then right-cli ck the Local Area Connection icon and then click Properties. 2. Click Internet Protocol (TCP/IP) and then click Pr operties. Then click on Use the follow IP address , and mak e s ur e y o ...
-
Airlink101 APO1200 - page 15
14 T echnical Support E-mail: support@airlink101.com T oll Free: 1-888-7 46- 3238 W e b Site: www .airlink101.com *Theoretical maximum wireless signal rate derived from IE EE standard 802.1 1 specifications . Ac tual data throughput will vary . Netw ork cond itions and environm e ntal factors, including volum e of network traff ic, building mate ri ...
¿Tienes una pregunta acerca de Airlink101 APO1200?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Airlink101 APO1200, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Airlink101 APO1200 probablemente compartirá una forma de solucionarlo.