-
Frymaster none - page 1
Frymaster, a member of th e Commercial Food Equi pment Service Association , recommends usin g CFES A Certi fied Te chnicia ns. Price: $6 .00 *8195931* 24-Hour Service H otline 1-800-5 51-8633 819-5931 April 2003 Heated Pass Through Installation, Operation, Servi ce, and Parts Manual ...
-
Frymaster none - page 2
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 1 1. Parts Ordering and Service Infor mation Parts orders ma y be placed direct l y with your local Fr ymaster Factor y Authori zed S ervice Cent er (FASC)/Distributor . A list of Fryma ster FASC/ Distributors was inc luded with the unit when shipped from the factor y. Your nea ...
-
Frymaster none - page 3
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 2 Power Requirements: • Voltage – 208 VAC • Frequency - 60 Hz • Single Pha se • 20 amp Service 4. Operation 1. Plug the unit into the power source. * 2. Press the ON/OFF r ocker switch to the ON position. 3. Place product in the HPT in accord ance with the restaurant? ...
-
Frymaster none - page 4
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 3 5. Maintenance Daily 1. Remove all product and turn the unit off. 2. Allow the unit to cool. 3. Use a wet sanitized cloth to clean the heat ed su rfaces of the unit. Use a n ylon pot brush on hard to remove stains or food items. Monthly Remove the filter scre en and clean it ...
-
Frymaster none - page 5
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 4 6.2 Replacing the T emperature Probe or High Limit The rmostat A. Disconnect the unit from the electrical powe r source. B. Turn the unit on its side. Remove th e five screws f rom the chassis bottom. C. Set the unit down on its base. D. Carefully lif t the cowl assembly upwa ...
-
Frymaster none - page 6
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 5 G. Disconnect the plate ground wire from the push- on terminal on the back wall of the air tower. H. Using a thin, sharp knife inserted bet ween the plate and the HPT ch assis, carefull y cut the silicon adhesive between the plate and the sides of the chassis. I. Pry up one e ...
-
Frymaster none - page 7
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 6 F. Cut the wire ties on the wirin g bundle and, on e at a time, disconnect the wires from the failed assembl y and connect the corres pondin g wire from the replacem ent motor. G. Position the replacement motor over the mountin g studs and secure it in place with the 5 ⁄ 16 ...
-
Frymaster none - page 8
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 7 7. Wiring Diagram ...
-
Frymaster none - page 9
HEATED PASS THROUGH INSTA LLA TION, OPERA TION , SERV ICE, A ND PA R TS 8 8 Common Repair Parts List 7 1 2 3 4 5 6 8 9 10 11 12 ITEM PART # COMPONENT 1 826-1561 Pad, Leg (pkg of 4) 2 823-3922 Divider Assembl y 3 810-1724 Screen, HPT Filter 4 807-3308 Switch, Black ON/OFF Rocker 5 807-3533 Relay, 18-Amp Solid State 6 807-2820 Block, .25 X 1.25 2-pol ...
-
Frymaster none - page 10
NOTICE IF, DU RING THE WA RRA NTY PERI OD, THE CU STO MER USES A PART FOR THIS ENO DIS EQUI PMEN T OT HER THA N A N UNMO DIFI ED NEW O R RE CYCLE D PA RT PURC HA SED DIRE CTLY FROM FRYMASTER/DE AN, OR ANY OF ITS AUTHORIZ ED SERV ICE CENTERS , AND/OR TH E PART BEIN G USED IS MODIFIED FROM ITS ORIGIN AL CONFIGUR ATION, THIS WARRANTY WILL BE VO ID. FU ...
-
Frymaster none - page 11
THIS PAGE INTENTIONALLY LEFT BLANK ...
-
Frymaster none - page 12
Frymaster, L.L. C., 8700 Line Avenue, PO Bo x 51000, Sh reveport, Louisi ana 711 35-1000 Shipping Address: 8700 Line Avenue, Shreveport, Louisiana 711 06 TEL 1-318-865-171 1 FAX (Parts) 1-318-2 19-71 40 FAX (Tech Support) 1-318-219-713 5 Price: $6.00 PRINTED IN THE UNITED STATES SERVIC E HOTL INE 1-800-551- 8633 819-5931 A pril 2003 ...
¿Tienes una pregunta acerca de Frymaster none?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Frymaster none, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Frymaster none probablemente compartirá una forma de solucionarlo.