Español dropdown-ico

Manual de instrucciones Miller Electric EXTREME 360

40 de páginas 1.45 mb
Descargar

Pasar a la página of 40

Summary
  • Miller Electric EXTREME 360 - page 1

    Pro cesses Descrip ti on Multiprocess W elding Arc Welding Power Source OM -229 409E 2007 − 11 EXTREME 360 CC/CV Auto-Line ...

  • Miller Electric EXTREME 360 - page 2

    ...

  • Miller Electric EXTREME 360 - page 3

    T ABLE OF CONTENTS SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1. Symbol Usage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2. Arc W elding Hazards 1 . . . . . . . ...

  • Miller Electric EXTREME 360 - page 4

    ...

  • Miller Electric EXTREME 360 - page 5

    OM-229 409 Page 1 SECTION 1 − SAFETY PRECAUTIONS - READ BEFORE USING som _2007 − 04 7 Protect yourself and others from injury — read and follow these precautions. 1-1. Symbol Usage DANGER! − Indicates a hazardous situation which, if not avoided, will result in death or serious injury . The possible hazards are shown in the adjoining symbols ...

  • Miller Electric EXTREME 360 - page 6

    OM-229 409 Page 2 W elding produces fumes and gases. Breathing these fumes and gases can be hazardous to your health. FUMES AND GASES can be hazardous. D Keep your head out of the fumes. Do not breathe the fumes. D If inside, ventilate the area and/or use local forced ventilation at the arc to remove welding fumes and gases. D If ventilation is poo ...

  • Miller Electric EXTREME 360 - page 7

    OM-229 409 Page 3 1-3. Additional Symbols For Installation, Operation, And Maintenance FIRE OR EXPLOSION hazard. D Do not install or place unit on, over , or near combustible surfaces. D Do not install unit near flammables. D Do not overload building wiring − be sure power supply system is properly sized, rated, and protected to handle this unit. ...

  • Miller Electric EXTREME 360 - page 8

    OM-229 409 Page 4 1-4. California Proposition 65 W arnings W elding or cutting equipment produces fumes or gases which contain chemicals known to the State of California to cause birth defects and, in some cases, cancer . (California Health & Safety Code Section 25249.5 et seq.) Battery posts, terminals and related accessories contain lead and ...

  • Miller Electric EXTREME 360 - page 9

    OM-229 409 Page 5 SECTION 2 − CONSIGNES DE SÉCURITÉ − LIRE A V ANT UTILISA TION fre_som_2007 − 04 7 Se protéger et protéger les autres contre le risque de blessure — lire et respecter ces consignes. 2-1. S ym bol es u t ilisés DANGER! − Indique une situation dangereuse qui si on l’évite pas peut donner la mort ou des blessures gra ...

  • Miller Electric EXTREME 360 - page 10

    OM-229 409 Page 6 Il reste une TENSION DC NON NÉGLIGEABLE dans les sources de soudage onduleur quand on a coupé l’alimentation. D Arrêter les convertisseurs, débrancher le courant électrique et décharger les condensateurs d’alimentation selon les instructions indiquées dans la partie Entretien avant de toucher les pièces. DES PIÈCES CH ...

  • Miller Electric EXTREME 360 - page 11

    OM-229 409 Page 7 LES ACCUMULA TIONS DE GAZ risquent de provoquer des blessures ou même la mort. D Fermer l’alimentation du gaz protecteur en cas de non-utilisation. D V eiller toujours à bien aérer les espaces confi- nés ou se servir d’un respirateur d’adduction d’air homologué. LES CHAMPS MAGNETIQUES peuv- ent affecter des implants m ...

  • Miller Electric EXTREME 360 - page 12

    OM-229 409 Page 8 LES FILS DE SOUDAGE peuvent provoquer des blessures. D Ne pas appuyer sur la gâchette avant d’en avoir reçu l’instruction. D Ne pas diriger le pistolet vers soi, d’autres per- sonnes ou toute pièce mécanique en enga- geant le fil de soudage. DES ORGANES MOBILES peuvent provoquer des blessures. D S’abstenir d e toucher ...

  • Miller Electric EXTREME 360 - page 13

    OM-229 409 Page 9 2-5. P r in ci pa le s no r m es d e sé cu r it é Safety i n W elding, Cutting, and Allied Processes, ANSI Standard Z49.1, de Global Engineering Documents (téléphone : 1-877-413-5184, site Internet : www .global.ihs.com). Recommended Safe Practices for the Preparation for W elding and Cut- ting of Containers and Piping , Ameri ...

  • Miller Electric EXTREME 360 - page 14

    OM-229 409 Page 10 ...

  • Miller Electric EXTREME 360 - page 15

    OM-229 409 Page 1 1 SECTION 3 − INTRODUCTION 3-1. Specifications Input V oltage Amperage Range in Max. Open- Circuit RMS Amps Input at Rated Load Output, 60 Hz 3-Phase at NEMA Load V oltages and Class I Rating Input Power Rated Output V oltage Range in CV Mode Range in CC Mode Circuit V oltage 208 V 230 V 400 V 460 V 575 V KV A KW 3-Phase 350 A a ...

  • Miller Electric EXTREME 360 - page 16

    OM-229 409 Page 12 6 Minutes W elding 4 Minutes Resting 3-3. Duty Cycle And Overheating Duty Cycle is percentage of 10 min- utes that unit can weld at rated load without overheating. If unit overheats, output stops, a Help message is displayed and cooling fan runs. W ait fifteen min- utes for unit to cool. Reduce amper- ag e or voltage, or duty cyc ...

  • Miller Electric EXTREME 360 - page 17

    OM-229 409 Page 13 SECTION 4 − INSTALLATION 4-1. Dimensions And Weight Hole Layout Dimensions 24 in (610 A E A 1 1-3/4 in (298 mm) (610 mm) G F B 1-1 1/16 in (42 mm) 17 in (432 mm) C 15-3/4 in (400 mm) D C D 19-3/32 in (485 mm) C E 8-1 1/16 in (221 mm) 12-1/2 in (318 mm) F 1-17/32 in (39 mm) 804 801-A B G 1/4-20 UNC -2B thread W eight 80 lb (36.3 ...

  • Miller Electric EXTREME 360 - page 18

    OM-229 409 Page 14 4-3. Connecting 1-Phase Input Power 804 531-A ! Installation must meet all Na- tional and Local Codes − have only qualified persons make this installation. ! Disconnect and lockout/tag- out input power before con- necting input conductors from unit. ! Always connect green or green/yellow conductor to supply grounding terminal f ...

  • Miller Electric EXTREME 360 - page 19

    OM-229 409 Page 15 4-4. Connecting 3-Phase Input Power 804 531-A ! Installation must meet all National an d Local Codes − have only quali- fied persons make this installation. ! Disconnect and lockout/tagout in- put power before connecting input conductors from unit. ! Always connect green or green/ yellow conductor to supply grounding terminal f ...

  • Miller Electric EXTREME 360 - page 20

    OM-229 409 Page 16 4-5. Electrical Service Guide NOTICE − INCORRECT INPUT POWER can damage this welding power source. Phase to ground voltage shall not exceed +10% of rated input voltage. NOTICE − Actual input voltage should not be 10% less than minimum and/or 10% more than maximum input voltages listed in table. If actua l input voltage is out ...

  • Miller Electric EXTREME 360 - page 21

    OM-229 409 Page 17 4-6. W eld Output Receptacles And Selecting Cable Sizes ! ARC WELDING can cause Electromagnetic Interference. T o reduce possible interference, keep weld cables as short as possible, close together, and down low , such as on the floor . Locate welding operation 100 meters from any sensitive electronic equipment. Be sure this weld ...

  • Miller Electric EXTREME 360 - page 22

    OM-229 409 Page 18 4-7. Remote 14 Receptacle Information Socket* Socket Information 24 VOL TS AC A 24 volts ac. Protected by circuit breaker CB2. AJ B K I 24 VOL TS AC B Contact closure to A completes 24 volts ac contactor control circuit. B K I C L NH 1 15 VOL TS AC I 1 15 volts ac. Protected by circuit breaker CB1. C NH D M G E F 1 15 VOL TS AC J ...

  • Miller Electric EXTREME 360 - page 23

    OM-229 409 Page 19 ‘ 4-9. Optional Gas V alve Operation And Shielding Gas Connection Ref. 803 705-A / Ref. 803 691-C Obtain gas cylinder and chain to running gear , wall, or other station- ary support so cylinder cannot fall and break of f valve. 1 Cylinder 2 Regulator/Flowmeter Install so face is vertical. 3 Gas Hose Connection Fitting has 5/8-1 ...

  • Miller Electric EXTREME 360 - page 24

    OM-229 409 Page 20 SECTION 5 − OPERATION V/A ADJUST ARC CONTROL ARC CONTROL REMOTE ELECTRODE HOT 5-1. Front Panel Controls 1 Power Switch . The fan motor is thermostatically controlled and only runs when cooling is needed. 2 V oltmeter 3 Ammeter 4 V/A (V oltage/Amperage) Adjustment Control 5 Mode Switch The Mode switch setting determines both th ...

  • Miller Electric EXTREME 360 - page 25

    OM-229 409 Page 21 5-2. Meter Functions . The meters display the actual weld output values for approximately three seconds after the arc is broken. Mode Meter Reading At Idle Meter Reading While W elding Scratch Start TIG VA Actual V olts (OCV) Preset Amps 71.7 85 Actual V olts Actual Amps VA 10.3 85 Lift-Arc TIG Actual V olts Preset Amps VA 14.1 8 ...

  • Miller Electric EXTREME 360 - page 26

    OM-229 409 Page 22 5-4. Lift-Arc TIG Procedure With Process Switch in the Lift-Arc TI G position, start an arc as follows: 1 TIG Electrode 2 W orkpiece T ouch tungsten electrode to work- piece at weld start point, hold electrode to workpiece for 1-2 seconds , and slowly lift electrode. An arc will form when electrode is lifted. Normal open-circuit ...

  • Miller Electric EXTREME 360 - page 27

    OM-229 409 Page 23 SECTION 6 − MAINTENANCE & TROUBLESHOOTING 6-1. Routine Maintenance . Maintain more often during severe conditions. ! Disconnect power before maintaining. 3 Months Replace Damaged Or Unreadable Labels Replace Cracked T orch Body Repair Or Replace Cracked Cables Repair Or Replace Cracked Cables And Cords Clean And Tighten W e ...

  • Miller Electric EXTREME 360 - page 28

    OM-229 409 Page 24 6-3. V oltmeter/Ammeter Help Displays . All directions are in reference to the front of the unit. All circuitry referred to is lo- cated inside the unit. 1 Help 1 Display Indicates a malfunction in the primary power circuit. If this display is shown, contact a Fac- tory Authorized Service Agent. 2 Help 2 Display Indicates a malfu ...

  • Miller Electric EXTREME 360 - page 29

    OM-229 409 Page 25 Notes Over 80,000 trained since 1930! 400 T rade Square East, T roy , Ohio 45373 1-800-332-9448 www.weldin g .or g Star t Y our Professional W eldin g Career Now! ...

  • Miller Electric EXTREME 360 - page 30

    OM-229 409 Page 26 SECTION 7 − ELECTRICAL DIAGRAM Figure 7-1. Circuit Diagram ...

  • Miller Electric EXTREME 360 - page 31

    OM-229 409 Page 27 21 1 328-F ...

  • Miller Electric EXTREME 360 - page 32

    OM-229 409 Page 28 SECTION 8 − P ARTS LIST Ref. 803 690-H 1 2 3 4 5 6 8 9 10 12 13 15 16 17 18 19 20 21 22 23 24 25 26 28 29 30 31 32 34 35 36 37 38 39 42 43 45 47 46 48 49 50 51 52 53 54 55 56 57 58 59 60 61 63 64 66 68 67 69 70 71 72 73 11 44 65 74 41 76 75 49 62 62 MOD 1 MOD 2 40 17 14 77 Figure 8-1. Parts Assembly ...

  • Miller Electric EXTREME 360 - page 33

    OM-229 409 Page 29 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Parts Assembly Quantity 1 229 541 Wrapper (Includes Insulators and Safety Labels) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 256 Insulator , Side Rh (Not Shown) 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric EXTREME 360 - page 34

    OM-229 409 Page 30 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Parts Assembly (Continued) Quantity 37 234 126 Nut, Conduit 1.000 Npt Knurled 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 T2 21 1 109 XFMR, Control 665V 336V a Syn Aux Pwr 1 . . . . . . . . . . . . . . . . . . ...

  • Miller Electric EXTREME 360 - page 35

    OM-229 409 Page 31 Description Part No. Dia. Mkgs. Item No. Figure 8-1. Parts Assembly (Continued) Quantity 70 174 992 Knob, Pointer .840 Dia X .250 Id W/Spring Clip − .21 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 212 949 Label, Process 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Miller Electric EXTREME 360 - page 36

    Notes Over 80,000 trained since 1930! 400 T rade Square East, T roy , Ohio 45373 1-800-332-9448 www.weldin g .or g Star t Y our Professional W eldin g Career Now! ...

  • Miller Electric EXTREME 360 - page 37

    Notes SOCKET/WRENCH SELECTION T ABLE (U.S. ST ANDARD) SOCKET/WRENCH SELECTION T ABLE (METRIC) Specifications Socket or Wrench Size Specifications Socket or Wrench Size Bolt Diameter Decimal Equivalent Bolt Nut Bolt Diameter U.S. Decimal Equivalent Bolt Nut 1/4 in .250 in 3/8 in 7/16 in 6 mm .2362 in 10 mm 10 mm 5/16 in .3125 in 1/2 in 9/16 in 8 mm ...

  • Miller Electric EXTREME 360 - page 38

    Notes 229895 MA TERIAL THICKNESS GAUGE ...

  • Miller Electric EXTREME 360 - page 39

    Effective January 1, 2007 (Equipment with a serial number preface of “LH” or newer) This limited warranty supersedes all previous manufacturers warranties and is exclusive with no other guarantees or warranties expressed or implied. LIMITED WARRANTY − Subject to the terms and conditions below , warrants to its original retail purchaser that n ...

  • Miller Electric EXTREME 360 - page 40

    PRINTED IN USA 1/07 Model Name Serial/Style Number Purchase Date (Date which equipment was delivered to original customer.) Distributor Address City State Zip Please complete and retain with your personal records. Contact the Delivering Carrier for: For assistance in filing or settling claims, contact your distributor and/or equipment manufacturer ...

Fabricante Miller Electric Categoría Welder

Los documentos del dispositivo Miller Electric EXTREME 360 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Miller Electric
- manuales de instrucciones EXTREME 360
- hojas de producto Miller Electric
- folletos informativos
- o etiquetas energéticas Miller Electric EXTREME 360
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Miller Electric EXTREME 360.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Miller Electric EXTREME 360, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Miller Electric EXTREME 360. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Miller Electric EXTREME 360.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Miller Electric EXTREME 360, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Miller Electric EXTREME 360. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Miller Electric EXTREME 360.

El manual de instrucciones completo de Miller Electric debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Miller Electric EXTREME 360 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Miller Electric EXTREME 360, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Miller Electric EXTREME 360 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Miller Electric EXTREME 360 - que deben facilitarnos los primeros pasos durante el uso de Miller Electric EXTREME 360
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Miller Electric EXTREME 360
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Miller Electric EXTREME 360 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Miller Electric EXTREME 360?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Miller Electric EXTREME 360, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Miller Electric EXTREME 360 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)