-
DeWalt DCD785C2R - page 1
www . .eu DCD730 DCD735 DCD780 DCD785 ...
-
DeWalt DCD785C2R - page 2
1 Figure 1 a b c d f e g h i k j h Figure 2 k j l ...
-
DeWalt DCD785C2R - page 3
2 Figure 3 Figure 7 c c f Figure 4 Figure 5 Figure 6 Figure 8 Figure 9 m n ...
-
DeWalt DCD785C2R - page 4
ENGLISH 33 CORDLESS COMP ACT 13 mm (1/2") DRILL/DRIVER DCD730, DCD780 CORDLESS COMP ACT 13 mm (1/2") DRILL/DRIVER/ HAMMERDRILL DCD735, DCD785 Congratulations! Y ou have chosen a D E WAL T tool. Y ears of experience, thorough pr oduct development and innovation make D E W AL T one of the most reliable partners for professional power tool u ...
-
DeWalt DCD785C2R - page 5
ENGLISH 34 Vibration emission value a h Screwdriving a h,ID = m/s² < 2.5 2.5 < 2.5 2.5 Uncertainty K = m/s² 1.5 1.5 1.5 1.5 The vibration emission level given in this information sheet has been measured in accor dance with a standardised test given in EN 60745 and may be used to compare one tool with another . It may be used for a prelimina ...
-
DeWalt DCD785C2R - page 6
ENGLISH 35 EC-Declaration of Conformity MACHINERY DIRECTIVE DCD730, DCD735, DCD780, DCD785 D E W AL T declares that these products described under T echnical Data are in compliance with: 2006/42/EC, EN 60745-1, EN 60745-2-1, EN 60745-2-2. These products also comply with Dir ective 2004/108/EC and 2011/65/EU. For more information, please contact D E ...
-
DeWalt DCD785C2R - page 7
ENGLISH 36 d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury . e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly . Do not ...
-
DeWalt DCD785C2R - page 8
ENGLISH 37 • W ear safety goggles or other eye protection. Hammering and drilling operations cause chips to fly . Flying particles can cause permanent eye damage. • Accessories and tool may get hot during operation. Wear gloves when handling them if performing heat producing applications such as hammerdrilling and drilling metals. • Do not op ...
-
DeWalt DCD785C2R - page 9
ENGLISH 38 • Do not use an extension cord unless it is absolutely necessary . Use of improper extension cord could result in risk of fire, electric shock or electrocution. • When operating a charger outdoors, always provide a dry location and use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk ...
-
DeWalt DCD785C2R - page 10
ENGLISH 39 Important Safety Instructions for All Battery Packs When ordering r eplacement battery packs, be sure to include the catalog number and voltage. The battery pack is not fully charged out of the carton. Before using the battery pack and charger , read the safety instructions below and then follow the charging procedur es outlined. READ AL ...
-
DeWalt DCD785C2R - page 11
ENGLISH 40 Read instruction manual before use. Charging. Fully charged. Hot/cold pack delay . x Problem pack or charger . Problem powerline. Do not probe with conductive objects. Do not charge damaged battery packs. Use only with D E W AL T battery packs. Others may burst, causing personal injury and damage. Do not expose to water . Have defective ...
-
DeWalt DCD785C2R - page 12
ENGLISH 41 Electrical Safety The electric motor has been designed for one voltage only . Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains. Y our D E WAL T charger is double insulated in accordance with EN 60335; ther efore no ...
-
DeWalt DCD785C2R - page 13
ENGLISH 42 NOTE: The first time the tool is run after changing the direction of r otation, you may hear a click on start up. This is normal and does not indicate a problem. T orque Adjustment Collar (fi g. 1) Y our tool has an adjustable torque screwdriver mechanism for driving and removing a wide array of fastener shapes and sizes and in some mod ...
-
DeWalt DCD785C2R - page 14
ENGLISH 43 T o move belt hook or bit clip, remove the scr ew (h) that holds it in place then reassemble on the opposite side. Be sure to secur ely tighten the screw . OPERA TION Instructions for Use WARNING: Always observe the safety instructions and applicable regulations. WARNING: T o reduce the risk of serious personal injury , turn tool off and ...
-
DeWalt DCD785C2R - page 15
ENGLISH 44 NOTE: A smooth, even flow of dust from the hole indicates proper drilling rate. Screwdriver Operation (fi g. 6) 1. Select the desired speed/torque range using the dual range gear selector to match the speed and torque of the planned operation. 2. T ur n the torque adjustment collar (c) to the desired position. Lower numbers indicate low ...
-
DeWalt DCD785C2R - page 16
ENGLISH 45 advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. Y ou can check the location of your nearest authorised repair agent by contacting your local D E W AL T office at the address indicated in this manual. Alternatively , a list of authorised D E WA L T repair agents and ...
¿Tienes una pregunta acerca de DeWalt DCD785C2R?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con DeWalt DCD785C2R, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con DeWalt DCD785C2R probablemente compartirá una forma de solucionarlo.