-
Metabo SB 200 CT - page 1
115 117 9491 / 2402 - 3.2 / de, en, fr, nl Achtung! Lesen Sie diese Anleitung vor der Installation und Inbetriebnahme aufmerksam durch. Attention! Carefully read through these instructions prior to installation and commissioning. Attention ! Prière de lire attentivement la présente notice avant l'installation et la mise en service. Oppassen! ...
-
Metabo SB 200 CT - page 2
D DEUTSCH ENG ENGLISH KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY Wir erklären in alleiniger Verantwortlichkeit, daß dieses Produkt mit den folgenden Normen übereinstimmt* gemäß den Bestimmungen der Richtlinien**. We herewith declare in our sole responsibility that this product complies with the following standards* in accordance with th ...
-
Metabo SB 200 CT - page 3
1 Specifications 2 Taking a Single-Phase Machine Into Operation 2.1 Taking a Combination 1-Ph/2-Ph Machine into Operation 3 General Information for Welding Transformer/Rectifier Operators 3.1 Overview of Stick Electrodes and their correct Use 3.1.1 Care of Stick Electrodes 3.1.2 Function of the Stick Electrode Coating 3.1.3 Classification of Stick ...
-
Metabo SB 200 CT - page 4
Example: Stick electrode DIN 913 - E 43 3 2 AR 7 Type of electrode Number of DIN standard Code for manual electric arc welding Code number for tensile strength, yield point and elongation Code number for impact engergy of 28 Joule minimum Code number for increased impact energy of 47 Joule minimum Code for coating Code number for electrode class 3. ...
-
Metabo SB 200 CT - page 5
3.1.2 Function of the Stick Electrode Coating Stabilization of the arc and lonization of the arc space Protection of the weld metal from atmospheric oxygen and nitrogen This protection is achieved by the generation of shielding gases and slag during the melting of the electrode. Compensation of alloy burn-off. bare electrode unstable arc coated ele ...
-
Metabo SB 200 CT - page 6
Code Weld Position Code Letter For Welding Position 1 all w, h, hü, s, f, q, ü 2 all except vertical-down w , h , hü, s, q, ü 3 gravity position w fillet weld gravity position w horizontal h 4 gravity position w 3.1.3 Classification of Stick Electrodes according to Table 3 of DIN 1913 Grade Weld Position Stick Electrode Type A 2 R 2 R 3 R(C) 3 ...
-
Metabo SB 200 CT - page 7
Stick electrodes can be classified according to their coating as under: Type Code Type Coating Characteristics Type of Slag - Slag Removal Ability Penetration Depth - Gap Bridging Ability Weld Appearance Characteristics Electrode Manipula- tion O Bare Electrode finely distributed arc stabilizers in the electrode material minimal slag shallow - exce ...
-
Metabo SB 200 CT - page 8
Arc Length The arc length "a", that is the distance between the stick electrode and the work, should be: with stick electrodes of coating type R, RR, A, C = 1.0xd, with stick electrodes of coating type B = 0.5xd, Too long an arc reduces the penetration, increases the arc blow effect and, particularly with basic coated stick electrodes, ca ...
-
Metabo SB 200 CT - page 9
4 Welding Hints Because of the multitude of and great differences in the important points for welding only the very basic operations for the most common electrodes for low-carbon steels, the Ti-type electrode, are introduced here. In the case that other electrodes have to be used, the electrode manufacturers supply upon request all relevant informa ...
-
Metabo SB 200 CT - page 10
For Fillet Welds "a" is the throat width size. The throat width should be at least x 0.7 the plate thickness of the thinner plate. 4.1 Weld Types For Butt Welds the work piece edges should be bevelled to approx. 30 ° , which gives a groove angle of 60 ° (Pic. 10). The root opening between the two work pieces should be 2 - 3 mm. 60° (Pi ...
-
Metabo SB 200 CT - page 11
4.2 Weld Flaws and possible Causes - Shown on Fillet Welds 21 Attach earth clamp as close as possible to the weld. Structural components, beams, pipes or rails should not be used for earth conducting if they are not the actual work piece. Replace broken insulating parts at once! Clean work piece surface for good conduction Ring tongue terminal sold ...
-
Metabo SB 200 CT - page 12
6 Wiring Diagrams 6 Schaltpläne 6 Schémas électriques 6 Schakelschema's 42 N L1 L2 CEE Plug 3P+N+PE CEE Adapter 3P+N+PE N L1 L2 Red Light Plug 230 V 400 V 400 V 230 V Schwitch Positions Contacts N - N L1 - L1 L2 - L2 230 V OFF OFF ON 0 ON ON ON 400 V On OFF OFF PE II I SB 160 C (230/400 V) SB 200 CT (240 V) Transformer N L1 PE 240V 0 Volta ...
-
Metabo SB 200 CT - page 13
SB 200 CT (230/400 V) 43 N L1 L2 CEE Plug 3P+N+PE CEE Adapter 3P+N+PE N L1 L2 Red Light II I Plug 230 V 400 V 400 V 230 V Schwitch Positions Contacts N - N L1 - L1 L2 - L2 230 V OFF OFF ON 0 ON ON ON 400 V On OFF OFF PE ...
-
Metabo SB 200 CT - page 14
Country; Company; Address 1; A ddress 2; Cit y; Phone ; Fax; E-mail Albania; Extra Indu strial Goods; Rl. Fadil Rada 88; ; Tirana; (+355) 42 - 3 30 62; (+355) 42 - 3 30 62; abeqiri@t-on line.de Algerie; Had dad Equipement Profess ione; 98 A, Site du LycÈe; ; 16012 Rouiba; (+213) 21 - 85 49 05; (+21 3) 21 - 85 57 72; Argentina; Metab o Argentia S.A ...
¿Tienes una pregunta acerca de Metabo SB 200 CT?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Metabo SB 200 CT, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Metabo SB 200 CT probablemente compartirá una forma de solucionarlo.