-
Makita DA3000DW - page 1
Cordless Angle Drill Capacities SteelIWood Wood screw No load speed 700 Rimin 4 5 mm x 20 mm 13/16" x 3/4"1 10 mm 13/8"1 10 mm (3/8") MODEL DA3000D 10 mm (3/8") MODEL DA3000DW With Fast Charger Net weight Overall length 1 2 kg 12 6 lbsl 290 mm 11 1-3/8"1 INSTRUCTION MANUAL Battery Cartridge 7000 Voltage Charging time 7 ...
-
Makita DA3000DW - page 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 0. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit ...
-
Makita DA3000DW - page 3
14. 15. 16. 17. 18. 19. 20. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turn- ing it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS. When tool is used outd ...
-
Makita DA3000DW - page 4
IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) 25 AWG Size of Cord 18 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 50 100 150 18 18 16 SAVE THESE INSTRUCTIONS - This manual Do not operate charger with damaged cord or plug - replace them im- mediately. Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any ...
-
Makita DA3000DW - page 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC 3. Do not allow anything to cover or clog the charger vents. 4. Do not short the battery cartridge. A battery short can ...
-
Makita DA3000DW - page 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. *To insert the battery cartridge, align the tongue on the battery cartridge with ...
-
Makita DA3000DW - page 7
Installing and removing bit CAUTION : Be sure that the battery cartridge has been removed from the tool. .To install the drill bit, place it in the chuck as far as it will go. Tighten the chuck collar by hand. Place the chuck key in each of three holes, and tighten clockwise. To remove the drill bit, place the chuck key into the chuck hole and turn ...
-
Makita DA3000DW - page 8
Switch action oset the reversing switch lever just in front of the trigger switch to Forward (FWD) or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the opposite side. The tr ...
-
Makita DA3000DW - page 9
0 Use tate Item Screwdriving cutting lubricant on the bit to facili- ! drilling if necessary. Nominal Diameter (mm) Bit No. Phillips bits Wood Screw 2.1 - 2.7 (3/32" - 1/8") 3.1 - 4.5 (1/8" - 3/16") Select your screws and nominal dia- meter with the chart on the right. Slotted bits Select a slotted bit to match the slot on the s ...
-
Makita DA3000DW - page 10
Hole .The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. Hole 1 10 ...
-
Makita DA3000DW - page 11
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11 ...
-
Makita DA3000DW - page 12
ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 0 Bits Square drill bit [ 784606-0A 0 Fast ...
-
Makita DA3000DW - page 13
0 Steel case Part NO. 181697-5 13 ...
-
Makita DA3000DW - page 14
Sep-19284 US 10 mm (3/8") CORDLESS ANGLE DRILL Model DA3000D Note: The switch and other part configurations may differ from country to country. 14 ...
-
Makita DA3000DW - page 15
MODEL OA30000 'ikM DESCRIPTION 11 21 31 41 51 61 71 81 Aug.-09-'84 US ,,!& DESCRIFTION 10 11 13 14 15 16 24 91 1 1 1 9 1 1 2 Orill Chuck 510 0 Ring 34 Plane Bearing 5 Housing Set IWnh Item 11 ) Holder 6 Gear Plane 0earmg 4 Current Relay Switch Motor tioUSlng Set wth Item 41 Name Plate Screw M4x22 [With Washer1 Set Plate Battery 7000 R ...
-
Makita DA3000DW - page 16
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh ...
¿Tienes una pregunta acerca de Makita DA3000DW?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Makita DA3000DW, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Makita DA3000DW probablemente compartirá una forma de solucionarlo.