-
McIntosh MCC204 - page 1
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New Y ork 13903-2699 Phone: 607-723-3512 F AX: 607-724-0549 Owner s Manual MCC204 MCC204 Power Amplifier ...
-
McIntosh MCC204 - page 2
2 IMPOR T ANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERA TING THIS EQUIPMENT . General: 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. W arning: T o reduce risk of fir e or electrical shock, do not expose this equipment to rain or moisture. This unit is capable of pr oducing high ...
-
McIntosh MCC204 - page 3
3 Customer Service T echnical Assist ance Please T ake A Moment Thank Y ou Copyright 2001 ã by McIntosh Laboratory , Inc. The serial number , purchase date and McIntosh dealer name are important to you for possible insurance claim or future service. The spaces below have been provided for you to record that information: Y our decision to own this ...
-
McIntosh MCC204 - page 4
4 Performance Features Introduction · Power Output The MCC204 consists of four separate power amplifier channels, each capable of 50 watts into 4 ohm speakers with less than 0.005% distortion. · Four Bridgeable Channels The MCC204 includes four 50 watt amplifier channels. Each pair of channels can be set in bridged configuration for 200 watts out ...
-
McIntosh MCC204 - page 5
5 Dimensions The following dimensions can assist in determining the best location for your MCC204. There is additional infor - mation on the next page pertaining to installing the MCC204 into your vehicle. Dimensions ...
-
McIntosh MCC204 - page 6
6 Inst allation Inst allation It is recommended that a professional who is skilled in all aspects of installation and operation install the MCC204 and any associated mobile audio equipment. Amplifier V entilation Always provide adequate ventilation for the MCC204. The amplifier requires an adequate airflow into the cooling fan, which is located on ...
-
McIntosh MCC204 - page 7
7 Side Panel Cooling and Connections Connect to the positve (+) vehicle battery terminal with an inline fuse INPUT s for audio cables from a signal source Controls the Power Guard Circuit when connected to certain McIntosh Control Centers Cooling Fan Air Intake OUTPUT Connections for loudspeakers SUBWOOFER OUTPUTS supply a four channel summed outpu ...
-
McIntosh MCC204 - page 8
8 How to Connect for Four Channels How to Connect for Four Channels 1. Connect a wire from the Control Center Amp On to the MCC204 ON Connector on the right side of the ampli- fier . Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery . 2. Connect a wire from a McIntosh Control Center with Powe ...
-
McIntosh MCC204 - page 9
9 How to Connect for Three Channels How to Connect for Three Channels 1. Connect a wire from the Control Center Amp On to the MCC204 ON connector on the right side of the ampli- fier . Note: All cables should be connected to the amplifier befor e connecting the DC power cables to the battery . 2. Connect a wire from a McIntosh Control Center with P ...
-
McIntosh MCC204 - page 10
10 How to Connect for T wo Channels How to Connect for T wo Channels 1. Connect a wire from the Control Center Amp On to the MCC204 ON Connector on the right side of the amplifier . Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery . 2. Connect a wire from a McIntosh Control Center with Power ...
-
McIntosh MCC204 - page 11
11 How to Connect with Subwoofer Channel How to Connect with Subwoofer Channel 1. Connect a wire from the Control Center Amp On to the MCC204 ON Connector on the right side of the amplifier . Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery . 2. Connect a wire from a McIntosh Control Center ...
-
McIntosh MCC204 - page 12
12 T op Panel Controls, Display and Switches POWER GUARD LED lights when the Power Guard Circuit acti- vates for Am- plifier Channels 1 or 2 CH 1-2 MODE Switch selects STEREO or BRIDGE mode of operation CROSSOVER Filter Switch and Control se- lect the low roll-of f fre- quency , high roll-off frequency or flat fre- quency response CH 3-4 SENSITIVIT ...
-
McIntosh MCC204 - page 13
13 The McIntosh MCC204 is a highly versatile amplifier that can be configured in many ways. This manual gives ex- amples of some of the most common configurations. The best way to set equalization and filter controls is through the use of a real-time spectrum analyzer and the expertise of a professional installer. This manual will guide you through ...
-
McIntosh MCC204 - page 14
14 How to Operate in Four or Three Channel Mode How to Operate Four Channel Mode How to Operate Three Channel Mode In the Four Channel Mode, all channels operate as inde- pendent 50 watt amplifiers. A typical four channel applica- tion is to drive a pair of full range loudspeakers in the front section of a vehicle and a second pair in the rear . Re ...
-
McIntosh MCC204 - page 15
15 How to Operate in T wo Channel or Subwoofer Mode How to Operate in T wo Channel Mode How to Operate in Subwoofer Mode In the T wo Channel Mode, Channels 1 and 2, and Channels 3 and 4 operate in bridged configuration as a pair of full frequency range 200 watt amplifiers. A typical application is use of a more powerful amplifier for stereo reprodu ...
-
McIntosh MCC204 - page 16
16 How to Replace the Fuses How to Replace the Fuses If the MCC204 produces no sound, there is no Illumination of the Nomenclature on the T op Glass Panel, and the power connections seem secure, one or more of the Amplifier s Fuse(s) may have failed. Under normal operating conditions your amplifier s fuses should not fail. Failure of a fuse ...
-
McIntosh MCC204 - page 17
17 Block Diagram MCC204 Block Diagram ...
-
McIntosh MCC204 - page 18
18 Specifications Specifications Power Output Per Channel 50 watts into 4 ohm loads and 100 watts into 2 ohm loads is the minimum sine wave continuous average power out- put per channel all four channels operating. Power Output Bridged 200 watts into 4 ohm loads is the minimum sine wave con- tinuous average power output. Rated Power Band 20Hz to 20 ...
-
McIntosh MCC204 - page 19
19 Packing Instructions Quantity Part Number Description 1 034162 Shipping carton only 2 034132 End cap (Foam pad) Packing Instructions In the event it is necessary to repack the equipment for shipment, the equipment must be packed exactly as shown below , failure to do so will result in shipping damage. Make sure that the T op Glass Panel is firml ...
-
McIntosh MCC204 - page 20
McIntosh Part No. 040765 McIntosh Laboratory , Inc. 2 Chambers Street Binghamton, NY 13903 ...
¿Tienes una pregunta acerca de McIntosh MCC204?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con McIntosh MCC204, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con McIntosh MCC204 probablemente compartirá una forma de solucionarlo.