-
Kenwood TK-7160 - page 1
TK-7160/ TK-8160 TK-7160H/ TK-8160H VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL ÉMETTEUR-RÉCEPTEUR FM VHF/ ÉMETTEUR-RÉCEPTEUR FM UHF MODE D’EMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES © B62-1829-10 (K, M) 09 08 07 06 05 04 03 02 01 ...
-
Kenwood TK-7160 - page 2
VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7160/ TK-8160 TK-7160H/ TK-8160H INSTRUCTION MANUAL ENGLISH ...
-
Kenwood TK-7160 - page 3
i T HANK Y OU We are grateful you chose KENWOOD for your personal mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency . KENWOOD transceivers incorporate the latest in advanced technology . As a result, we feel strongly that you will be pleased with the qu ...
-
Kenwood TK-7160 - page 4
ii P RECAUTIONS Observe the following precautions to prevent fire, personal injury , and transceiver damage. • Do not attempt to configure the transceiver while driving; it is too dangerous. • Do not disassemble or modify the transceiver for any reason. • Do not expose the transceiver to long periods of direct sunlight, nor place it near heat ...
-
Kenwood TK-7160 - page 5
iii CONTENTS UNP ACKING AND CHECKING EQUIPMENT ................................... 1 S UPPLIED A CCESSORIES ..................................................................... 1 PREP ARA TION .................................................................................. 2 T OOLS R EQUIRED ...................................................... ...
-
Kenwood TK-7160 - page 6
iv CODE SQUELCH (ID CODE) .......................................................... 17 R ECEIVING ...................................................................................... 17 T RANSMITTING ................................................................................. 17 SELECTIVE CALL ............................................... ...
-
Kenwood TK-7160 - page 7
1 Note: The following unpacking instructions are for use by your KENWOOD dealer , an authorized KENWOOD service facility , or the factory . Carefully unpack the transceiver . We recommend that you identify the items listed in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, f ...
-
Kenwood TK-7160 - page 8
2 V arious electronic equipment in your vehicle may malfunction if they are not properly protected from the radio frequency energy which is present while transmitting. Electronic fuel injection, anti-skid braking, and cruise control systems are typical examples of equipment that may malfunction. If your vehicle contains such equipment, consult the ...
-
Kenwood TK-7160 - page 9
3 I NST ALLING THE T RANSCEIVER For passenger safety , install the transceiver securely using the supplied mounting bracket, so the transceiver will not break loose in the event of a collision. 1 Mark the position of the holes in the dash by using the mounting bracket as a template. Drill the holes, then attach the mounting bracket using the suppli ...
-
Kenwood TK-7160 - page 10
4 C ONNECTING A M ICROPHONE 1 Insert the microphone plug into the jack on the front panel of the transceiver . • Be sure the tab on the microphone plug is facing the left hand side. 2 Mount the microphone on the microphone hanger where it will be within easy reach of the user . 3 To remove the microphone plug, press the tab on the connector while ...
-
Kenwood TK-7160 - page 11
5 GETTING ACQUAINTED F RONT P ANEL q q q q q (Power) switch Press to switch the transceiver ON or OFF . w w w w w key Press to activate its programmable function {page 8}. The default setting is V olume Up. e e e e e key Press to activate its programmable function {page 8}. The default setting is V olume Down. r r r r r Display Refer to page 7. t t ...
-
Kenwood TK-7160 - page 12
6 !1 !1 !1 !1 !1 A key Press to activate its programmable function {page 8}. The default setting is None (no function). !2 !2 !2 !2 !2 <B key Press to activate its programmable function {page 8}. The default setting is Channel Down. !3 !3 !3 !3 !3 C> key Press to activate its programmable function {page 8}. The default setting is Channel Up. ...
-
Kenwood TK-7160 - page 13
7 D ISPLA Y R EAR P ANEL External speaker jack Power input connector Antenna connector r o t a c i d n I n o i t p i r c s e D s a d e m m a r g o r p y e k e h t n e h w s r a e p p A r o t i n o M r o f f O h c l e u q S s i . d e s s e r p n i e d o c e h t s e h c t a m l l a c a f o e d o c e n o t - 2 r o F M T D e h t n e h w s r a e p p A . ...
-
Kenwood TK-7160 - page 14
8 PROGRAMMABLE FUNCTIONS The , , , , S , A , <B , C> , and keys can be programmed with the functions listed below: • 2-tone Encode Press to enter 2-tone Encode Select mode. Refer to page 19 for details. • AUX Press to activate the auxiliary port. Press again to deactivate the auxiliary port. (The auxiliary port is used with optional board ...
-
Kenwood TK-7160 - page 15
9 • None No function is programmed onto the key . • Operator Selectable T one Press to enter OST (Operator Selectable T one) Select mode. Refer to page 16 for details. • Public Address Press to activate the Public Address (P A) system. Refer to page 24 for details. • Scan Del/Add Press to add or remove the selected channel to/from the Scan ...
-
Kenwood TK-7160 - page 16
10 BASIC OPERA TIONS S WITCHING P OWER ON/ OFF Press the switch to switch the transceiver ON. •A beep sounds. If programmed, an 8-character power-on message is also momentarily displayed. • If the T ransceiver Password function is programmed, “ ” will appear on the display when the power is turned ON. Refer to “T ransceiver Password”, b ...
-
Kenwood TK-7160 - page 17
11 S ELECTING A Z ONE AND C HANNEL Select the desired zone using the keys programmed as Zone Up and Zone Down . • The default setting for the key is Zone Up . • The default setting for the key is Zone Down . Select the desired channel using the keys programmed as Channel Up and Channel Down . • The default setting for the <B key is Channel ...
-
Kenwood TK-7160 - page 18
12 SCAN Scan is useful for monitoring signals on the transceiver channels. Scan can be used as either Single Scan or Multi Scan and is programmed by your dealer . • Single Scan monitors only the channels of a single zone. T o monitor other zones, press the Zone Up or Zone Down key during Scan. Scan will then begin monitoring the channels of the n ...
-
Kenwood TK-7160 - page 19
13 A DD TO S CAN / D ELETE FROM S CAN Depending on how your transceiver has been set up, a key may have been programmed with the Scan Del/Add function. This function allows you to scan only those channels which you desire. To add or remove a channel to/from the Scan list, select the desired channel then press the Scan Del/Add key . To temporarily r ...
-
Kenwood TK-7160 - page 20
14 DTMF CALLS Note: T o make DTMF calls, you must have an optional microphone with a DTMF keypad. S TORE & S END 1 Enter the desired digits on the microphone keypad. •Y ou can enter a maximum of 16 digits ( 0 ~ 9 , A ~ D , , and # ). • The digits appear on the display as you enter them. • If Keypad Auto-PTT is enabled by your dealer , thi ...
-
Kenwood TK-7160 - page 21
15 D IALING S TORED DTMF N UMBERS 1 Press the microphone key . •“ ” appears on the display . 2 Enter the desired memory location number (1 ~ 9). • The digits stored in the selected location number appear on the display . •T o cancel, press any key other than the PTT switch. 3 Press the PTT switch. • If programmed by your dealer , no DTM ...
-
Kenwood TK-7160 - page 22
16 QUIET T ALK (QT)/ DIGIT AL QUIET T ALK (DQT) Y our dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls from other parties who are using the same channel. When a channel is set up with a QT tone or DQT code, squelch will only open w ...
-
Kenwood TK-7160 - page 23
17 CODE SQUELCH (ID CODE) Code Squelch is enabled or disabled by your dealer . This function turns the transceiver squelch OFF only when it receives the DTMF ID code that has been set up in your transceiver . T ransceivers that do not transmit the correct code will not be heard. Consequently , you can communicate with a specific party without liste ...
-
Kenwood TK-7160 - page 24
18 SELECTIVE CALL Selective Call is enabled or disabled by your dealer . This function is similar to Code Squelch {page 17}. The dif ferences from Code Squelch are: •Y ou can send or receive Status codes containing up to 5 digits. • Selective Call opens the squelch only when the transceiver receives a predetermined DTMF code in the correct sequ ...
-
Kenwood TK-7160 - page 25
19 2-TONE SIGNALING 2-tone Signaling is enabled or disabled by your dealer . This function opens the squelch only when the transceiver receives the 2 tones corresponding to the 2-tone code set up on your transceiver . T ransceivers that do not transmit the correct tones will not be heard. R ECEIVING When you receive a signal containing the correct ...
-
Kenwood TK-7160 - page 26
20 FleetSync: ALPHANUMERIC 2-W A Y P AGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by KENWOOD Corporation. FleetSync enables a variety of paging functions on your transceiver , some of which depend on dealer programming. GPS R EPORT If a GPS unit (NMEA-0183 format) is installed on your transceiver and the ...
-
Kenwood TK-7160 - page 27
21 S TA TUS M ESSAGE Y ou can send and receive 2-digit Status messages which may be decided in your talk group. Messages can contain up to 16 alphanumeric characters. Status messages range from 10 to 99 (80 ~ 99 are reserved for special messages). A maximum of 5 received messages can be stored in the stack memory of your transceiver . These saved m ...
-
Kenwood TK-7160 - page 28
22 EMERGENCY OPERA TION If your transceiver has been programmed with the Emergency function, you can make emergency calls. 1 Press and hold the key programmed as Emergency . • Depending on the delay time programmed into your transceiver , the length of time you must hold the Emergency key will vary . • When the transceiver enters Emergency mode ...
-
Kenwood TK-7160 - page 29
23 ADV ANCED OPERA TIONS T ALK A ROUND Y ou may occasionally experience an interruption in service (due to a power failure, etc.). During such an occurence, you can continue communication by using the T alk Around feature if it has been programmed by your dealer . T alk Around allows you to communicate directly with other transceivers without the u ...
-
Kenwood TK-7160 - page 30
24 P UBLIC A DDRESS (P A) S YSTEM To use the Public Address system, your dealer must install an optional KAP-2 unit and an external speaker . This function causes all audio input via the microphone to be amplified and output from the external speaker . To use the P A system: 1 Press the key programmed as Public Address . • The icon appears on the ...
-
Kenwood TK-7160 - page 31
25 V OICE S CRAMBLER Note: There are 2 options for using the scrambler . Y our dealer can activate or deactivate the built-in scrambler function of the transceiver , or they can add a more secure optional scrambler board to your transceiver . Ask your dealer for details. Although the built-in scrambler function does not offer complete privacy with ...
-
Kenwood TK-7160 - page 32
26 BACKGROUND OPERA TIONS T IME - OUT T IMER (TOT) The purpose of the T ime-out T imer is to prevent any caller from using a channel for an extended period of time. If you continuously transmit for a period of time that exceeds the programmed time, the transceiver will stop transmitting and an alert tone will sound. T o stop the tone, release the P ...
¿Tienes una pregunta acerca de Kenwood TK-7160?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Kenwood TK-7160, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Kenwood TK-7160 probablemente compartirá una forma de solucionarlo.