-
Ryobi CTH1802 - page 1
THANK YOU FOR BUYING A R YOBI CORDLESS DRILL-DRIVER. Y our new cordless drill-driver has been engineered and manufactured to Ryobi’s high standard for dependability , ease of operation, and operator safety . Properly cared for , it will give you years of rugged, trouble-free performance. CAUTION: Carefully read through this entire operator's ...
-
Ryobi CTH1802 - page 2
Page 2 TABLE OF CONTENTS ■ T able Of Contents/T ypical Applications. ................................................................................ 2 ■ Rules For Safe Operation ................................................................................................... 3-5 A. Precautions On Using Y our Cordless T ool .................. ...
-
Ryobi CTH1802 - page 3
Page 3 RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper ac ...
-
Ryobi CTH1802 - page 4
Page 4 RULES FOR SAFE OPERA TION (Continued) when working outdoors. Wear protective hair covering to contain long hair and keep it from being drawn into nearby air vents. 9. ALWAYS WEAR SAFETY GLASSES. Everyday eyeglasses have only impact-resistant lenses; they are NOT safety glasses. 10. PROTECT YOUR LUNGS. Wear a face mask or dust mask if operati ...
-
Ryobi CTH1802 - page 5
Page 5 RULES FOR SAFE OPERA TION (Continued) 5. To reduce risk of damage to electric plug and cord, pull by the plug rather than the cord when disconnecting charger. 6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to damage or stress. 7. An extension cord should not be used unless absolutely nece ...
-
Ryobi CTH1802 - page 6
Page 6 SPECIFICATIONS: DRILL-DRIVER CTH1202K2 CTH1442K2 CTH1802 Chuck 3/8 in. Keyless 3/8 in. Keyless 1/2 in. Keyless Motor DC Motor 12.0 V DC Motor 14.4 V DC Motor 18.0 V Gear Train Two-Speed Two-Speed Two-Speed Switch Variable Speed Variable Speed Variable Speed No Load Speed 0-300 RPM (Low) 0-350 RPM (Low) 0-350 RPM (Low) 0-1000 RPM (High) 0-130 ...
-
Ryobi CTH1802 - page 7
Page 7 OPERA TION Fig. 1 Fig. 2 KNOW YOUR DRILL-DRIVER See Figures 1 and 2. Before attempting to use any tool, familiarize yourself with all operating features and safety requirements. W ARNING: Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient to inflict severe injury. CHARGING YO ...
-
Ryobi CTH1802 - page 8
Page 8 OPERA TION Fig. 5 Fig. 4 W ARNING: If any parts are missing, do not operate tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. SWITCH See Figure 4. Your drill starts and stops by depressing and releasing the switch trigger. Release the switch trigger to turn drill OFF . VARIABLE SPEE ...
-
Ryobi CTH1802 - page 9
Page 9 CHUCK BODY CHUCK COLLAR OPERA TION Fig. 6 Fig. 7 TO INSTALL BATTERY PACK ■ Place the direction of rotation selector in center posi- tion. See Figure 4. ■ Place the battery pack in your drill. Align raised rib on battery pack with groove in drill's battery port. See Fig- ure 6. ■ Make sure the latches on each side of your battery p ...
-
Ryobi CTH1802 - page 10
Page 10 OPERA TION Fig. 8 Fig. 10 INSTALLING AND REMOVING BITS ■ Place the direction of rotation selector at the center position. This will turn off the power to your drill. ■ Open or close the chuck jaws to a point where the opening is slightly larger than the bit size you intend to use. Also, raise the front of your drill slightly to keep the ...
-
Ryobi CTH1802 - page 11
Page 11 OPERA TION W ARNING: Be prepared for binding or breakthrough. When these situations occur , the drill has a tendency to grab and kick in the opposite direction, and could cause loss of control when breaking through material. If you are not prepared, this loss of control can result in possible serious injury . When drilling metals, use a lig ...
-
Ryobi CTH1802 - page 12
Page 12 OPERA TION Fig. 13 Fig. 14 CHUCK REMOV AL See Figures 13, 14, and 15. The chuck must be removed in order to use some accessories. T o remove: ■ Lock the switch trigger by placing the direction of rotation selector in center position. ■ Insert a 5/16 inch or larger allen wrench (hex key wrench) into the chuck of your drill and tighten th ...
-
Ryobi CTH1802 - page 13
Page 13 MAINTENANCE W ARNING: When servicing use only identical Ryobi replacement parts. Use of any other parts may create a hazard or cause product damage. A void using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use a clean cloth to remove ...
-
Ryobi CTH1802 - page 14
1980014 11-00 OPERA TOR'S MANUAL CORDLESS DRILL-DRIVER MODEL NOS. CTH1202K2/CTH1402K2/CTH1802 CTH1202K2/CTH1442K2/CTH1802 R YOBI TECHNOLOGIES INC. 1428 Pearman Dairy Road Anderson, SC 29622 Post Office Box 1207 Anderson, SC 29622-1207 Phone 1-800-525-2579 R YOBI TECHNOLOGIES INC. Post Office Box 910 Cambridge, Ontario N1R 6K2 Phone 1-800-265-6 ...
¿Tienes una pregunta acerca de Ryobi CTH1802?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Ryobi CTH1802, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Ryobi CTH1802 probablemente compartirá una forma de solucionarlo.