-
Legacy (F) - page 1
INST ALLER / CONSUMER SAFETY INFORMA TION Please read this manual before installing and using the heater . W ARNING: If the infor mation in this manual is not followed exactly , a fire or explosion may result causing pr operty damage, personal injury or loss of life. • Do not store or use gasoline or other flammable vapors and liquids in the vici ...
-
Legacy (F) - page 2
2 General Information SAFETY : Accidents are always tragic especially because so many of them could have been prevented with a little care and attention. These are some basic good practices we hope you will follow for safe use of your gas fired room heater . IMPOR T ANT : Read this user's manual carefully and completely before trying to assemb ...
-
Legacy (F) - page 3
3 RMC-LCNG, RMC-LCLP , RMC-LING, RMC-LILP Specifications Models (Manual & Thermostat) Gas T ype Input Rating (Btu/Hr) Variable Regulator Pressure Setting Inlet Gas Supply Pressure Size of Heater Weight Min. Max Min. Max RMC-LC30NG Natural 15,000 30,000 4.0” w .c. 5.0” w .c. 11” w.c. 27”x 24”x 8 1/2 ” 30 lbs. RMC-LC20NG 10,000 20,000 ...
-
Legacy (F) - page 4
4 Installation • This heater shall not be installed in a confined space or unusually tight construction unless provisions are provided for adequate combustion and ventilation air . • This hea ter must have fresh air for proper operation. If not, poor fuel combustion could result. Read the following instructions to insure proper fresh air for th ...
-
Legacy (F) - page 5
LOCA TING THE HEA TER 5 PREP ARING FOR INST ALLA TION 1. Remove hea ter from carton 2. Remove all protective packa ging applied to hea ter for shipment. 3. Check hea ter for any shipping damage. If heater is dama ged, promptly inform dealer/distributor . 4. Select a loca tion for the hea ter tha t will provide maximum exposure of the radiant surfac ...
-
Legacy (F) - page 6
6 FLOOR INST ALLA TION 1. Hea ter may only be installed on a noncombustible flat surface. Where the flooring is carpeting, tile or of other combustible material other than wood flooring, maintain the minimum clearances to the floor as shown in figure 2 or else use a metal or wood panel (not supplied) extending the full width and depth of the applia ...
-
Legacy (F) - page 7
7 Installation should be done by a qualified ser vice person. Before connecting the appliance, turn off all gas appliances. Close the main gas valve a t the gas meter or LP tank. Make certain there is good ventilation where the installation will be made. Installation should comply with all applicable building codes and ANSI Z223.1, latest edition. ...
-
Legacy (F) - page 8
8 Operation Instructions FOR YOUR SAFETY - READ THIS SECTION BEFORE LIGHTING A. BEFORE LIGHTING smell all around the appliance area for gas. Be sure to smell next to floor because some gas is heavier than air and will settle on the floor . LIGHTING INSTRUCTIONS W ARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTL Y , A FIRE OR EXPLOSION MA Y RE ...
-
Legacy (F) - page 9
9 T urning Heater Off Push in gas control knob slightly and turn c lockwise to "OFF" position. Do not force. T urning Burner Only Off (Pilot stays lit). T urn control knob clockwise to the PILOT position. C AUTION: Do not try to adjust heating levels by using the manual shut-off valve. NOTE: The thermostat sensing bulb measures the temper ...
-
Legacy (F) - page 10
10 Problem P ossible Cause What T o Do When control knob is pressed in and turned counterc lockwise to ignition, there is no spark at ODS pilot. 1. Ignitor electrode positioned wrong. 2. Ignitor electrode broken. 3. Ignitor cable pinched or broken. 4. Ignitor cable not connected to ignitor electrode. 1. Reposition ignitor electrode. 2. Replace elec ...
-
Legacy (F) - page 11
11 Problem P ossible Cause What T o Do Hea ter produces a clicking noise just after burner is lit or turned off. 1. Metal expanding and contracting. 1. This is common with heaters. If noise is excessive, contact a qualified service technician. Gas odor even when control knob is in OFF position. 1. Gas leaks. Refer to front of pa ge Warnings. 2. Gas ...
-
Legacy (F) - page 12
12 Item/Model Number RMC-LI06NG/LP RMC-LI10NG(T)/LP(T) RMC-LI18NG(T)/LP(T) RMC-LI30NG(T)/LP(T) 1. Lower Heat Cover LI10LP-01-01-02 LI10LP-01-01-02 LI18LPT -01-01-03 LI30NG-01-01-02 2. Guard Assembly LC10NG-01-04 LC10NG-01-04 LI18LPT -01-04 LC30NGTF-01-04 3. Reflector LI10LP-01-01-01 LI10LP-01-01-01 LI18LPT -01-01-01 LI30NG-01-01-01 4. Upper Heat Co ...
-
Legacy (F) - page 13
13 CFM Home Products reserves the right to make changes in design, ma terials, specifications, prices and discontinue colors and products at any time, without notice. W ARNING: F ailure to position the parts in accordance with this dia gram or failure to use only parts specifically approved with this heater may result in property damage or personal ...
-
Legacy (F) - page 14
14 The following accessories are available from your local distributors/dealer . Each accessor y comes with a separate installation instruction. Be sure to read each instruction thoroughly before installa tion. Accessories OPERATION & MAINTENANCE INSTRUCTIONS FMA-(F ,FT) MANUALL Y & THERMOST A TICALL Y CONTROLLED BLOWERS IMPOR T ANT : The b ...
-
Legacy (F) - page 15
15 Accessories continued C AUTION: Damaged power cord can cause a fire or electric shock. Prior to installing the blower , check for blower for any shipping dama ge. If blo wer is dama ged, promptly inform dealer where you bought the blo wer . INST ALLA TION: Plug the blo wer power cord into a 110-120V properly grounded type outlet (three prong rec ...
-
Legacy (F) - page 16
Service and Limited Warranty CFM Home Products warrants this product to be free from defects in materials and components for three (3) years from the da te of first purchase, provided that the product has been properly installed, opera ted and maintained in accordance with all a pplicable instructions. T o make a claim under this warranty the Bill ...
¿Tienes una pregunta acerca de Legacy (F)?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Legacy (F), haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Legacy (F) probablemente compartirá una forma de solucionarlo.