-
Craftsman 320.17217 - page 1
Operator's Manual j CRRFTSMRH°j evolv M 3/8" Keyless Drill Model No. 320.17217 000s WARNING: To reduce the risk of injury, the user must read and understand the Operator's Manual before using this product. • WARRANTY SAFETY ASSEMBLY DESCRIPTION OPERATION MAINTENANCE Sears Brands Management Corporation www.craftsman.com ...
-
Craftsman 320.17217 - page 2
Warranty Page 2 Safety Symbols Page 3 Safety Instructions Pages 4-7 Unpacking Pages 8 Description Pages 8-10 Operation Pages 10-13 Maintenance Page 14 Troubleshooting Page 15 Parts List Pages 16-17 Sears Repair Parts Phone Number Back Cover CRAFTSMAN@ EVOLV FULL WARRANTY If this Craftsman@ Evolv product fails due to a defect in material or workmans ...
-
Craftsman 320.17217 - page 3
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols and the explanations with them deserve your careful attention and understanding. The symbol warnings do not, by themselves, eliminate any danger. The instructions and warnings they give are no substitutes for proper accident prevention measures. ,_ WA ...
-
Craftsman 320.17217 - page 4
WARNING: Be sure to read and understand all instructions in this manual before using the drill. Failure to follow all instructions may result in hazardous radiation exposure, electric shock, fire, and/or serious personal injury. WARNING: Do not attempt to operate this tool until you have thoroughly read all instructions, safety rules, and warnings. ...
-
Craftsman 320.17217 - page 5
When in doubt, use the next heavier gauge. Always use UL and CSA listed extension cords. Recommended sizes of extension cords Ampere Rating More Than 0 6 10 12 Not More Than 6 10 12 16 Volts 120v Total Length of Cord in feet 25ft 50ft 100ft 150ft AWG 18 16 18 16 16 16 14 12 16 14 14 12 14 12 Not Recommended PERSONAL SAFETY Stay alert, watch what yo ...
-
Craftsman 320.17217 - page 6
unstable and may lead to loss of control. Do not force tool. Use the correct tool for your application. The correct tool will do the job better and more safely at the rate for which is designed. Do not use tool if the switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect ...
-
Craftsman 320.17217 - page 7
SAFETY SYMBOLS FOR YOUR TOOL The label on your tool may include the following symbols. V ............................................................... Volts A ............................................................... Amps Hz ............................................................. Hertz W ............................................... ...
-
Craftsman 320.17217 - page 8
_1_ WARNING: Your drill should never be connected to the power source when you are assembling parts, making adjustments, installing or removing bits, cleaning it, or when it is not in use. Disconnecting the drill will prevent accidental starting, which could cause serious personal injury. When unpacking the box, do not discard any packing materials ...
-
Craftsman 320.17217 - page 9
Fig. 2 Built-in belt chip Lock-on button Cord guard Keyless chuck Trigger switc Forward/reverse switch PRODUCT SPECIFICATIONS Motor 120V~60Hz, 5.2A No Load Speed 0-2500 (RPM) Chuck 3/8" (10ram) Cord length 6' Weight 3.1 Ibs WARNING: The safe use of this product requires an understanding of the information on the tool and in this operator& ...
-
Craftsman 320.17217 - page 10
CORD GUARD Protects the cord from bending to prevent damage. BUILT-IN BELT CLiP Conveniently hooks onto your tool belt for carrying the drill. NOTE: Make sure the plug has been removed from power supply and drill bits have been removed from drill. Your drill comes equipped with variable speeds, which can be adjusted by using the 2-finger trigger sw ...
-
Craftsman 320.17217 - page 11
the forward/reverse switch while the chuck is turning. ,_k WARNING: Always disconnect your drill from the power source when replacing drill bits, tools, cleaning or when it is not in use. Disconnecting the drill will prevent accidental starting that could cause serious personal injury. iNSTALLiNG DRILL BiTS AND ACCESSORIES (Fig.4) 1. Unplug your dr ...
-
Craftsman 320.17217 - page 12
,_ WARNING: Every time you use the drill, be sure to verify the following: • Chuck jaws are tight and securing the drill bit firmly. • Drill power cord is not damaged. • Drill bit is the correct type for the material being drilled. • Drill bit is in good condition, properly installed and securely tightened. • Safety glasses and dust mask ...
-
Craftsman 320.17217 - page 13
grasp the handle and trigger switch and the other to grasp the body of the drill. NOTE: Make sure that the hand placed on the body of the drill does not cover the air vents. Covering the air vents will reduce motor cooling and possibly lead to motor overheating. 4. Holding the drill firmly, place the point of the drill bit at the point to be drille ...
-
Craftsman 320.17217 - page 14
_, WARNING: To ensure safety and reliability, all repairs should be performed by a qualified service technician at a Sears store or other Craftsman Evolv outlet. ,_ WARNING: For your safety, always turn off the switch and disconnect the plug from the electrical outlet before performing any maintenance or cleaning. Periodic maintenance of your drill ...
-
Craftsman 320.17217 - page 15
PROBLEM The drill does Rot start when trigger switch is squeezed Will not drill Motor overheating CAUSE SOLUTION Check to be sure power cord is connected to power source and that power source (outlet) is operable Check drill bit and chuck jaws Be sure cooling vents are free from dust and obstacles Connect to power source. Confirm power source (outl ...
-
Craftsman 320.17217 - page 16
3/8" Keyless Drill MODEL NUMBER 320.17217 Always mention the Model Number when ordering parts for this tool : [: ! @ 17217 Manual Revised 09-0708 Page 16 ...
-
Craftsman 320.17217 - page 17
1 2 3 4 5 6 7 3860001000 5620179000 3550093000 5700015000 3520013000 3520016000 5700008000 Chuck Screw (L.H.) Spindle Ball Bearing Septa Gear Ball Bearing 1 1 1 1 2 1 2 8 3320036000 Le_ Housing 1 9 2240066000 Name Plate 1 10 3120245000 FIR Button 1 11 5610042000 Tapping Screw 9 12 2240073000 Name Plate 1 13 3320035000 Right Housing 1 14 2750119000 ...
-
Craftsman 320.17217 - page 18
17217 Manual Revised 09=0708 Page 18 ...
-
Craftsman 320.17217 - page 19
17217 Manual Revised 09=0708 Page 19 ...
-
Craftsman 320.17217 - page 20
Your Home For expert troubleshooting and home solutions advice: www.managemyhome.com For repair - in your home - of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it ! For the replacement parts, accessories and owner's manuals that you need to do-it-yourself. For ...
¿Tienes una pregunta acerca de Craftsman 320.17217?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Craftsman 320.17217, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Craftsman 320.17217 probablemente compartirá una forma de solucionarlo.