Español dropdown-ico

Manual de instrucciones Eaton Powerware BladeUPS Bar

28 de páginas 2.49 mb
Descargar

Pasar a la página of 28

Summary
  • Eaton Powerware BladeUPS Bar - page 1

    Powerware BladeUPS Bar Installation Guide ® ® ...

  • Eaton Powerware BladeUPS Bar - page 2

    Special Symbols The following are examples of symbols used on the UPS or accessories to alert you to important information: RISK OF ELECTRIC SHOCK - Observe the warning associated with the risk of electric shock symbol. CAUTION: REFER TO OPERATOR’S MANUAL - R efer to your operator’s manual for additional information, such as important operating ...

  • Eaton Powerware BladeUPS Bar - page 3

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 i Table of Contents 1 Introduction 1 ......................................................... Safety Warnings 2 ...................................................................... 2 Installation 5 .......................................................... Inspecting the E ...

  • Eaton Powerware BladeUPS Bar - page 4

    TABLE OF CONTENTS EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 ii ...

  • Eaton Powerware BladeUPS Bar - page 5

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 1 Chapter 1 Introduction Up to six of Eaton’s Powerware ® BladeUPS ® uninterruptible power systems (UPSs) can be installed in an industry standard rack outfitted with a BladeUPS Bar 60 for interconnecting the cabinets’ wiring. Figure 1 shows an installed BladeUPS Bar 60 ...

  • Eaton Powerware BladeUPS Bar - page 6

    INTRODUCTION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 2 Safety Warnings IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS This manual contains important instructions t hat you should follow during installation and maintenance of the BladeUPS Bar 60. Please r ead all instructions before operating the equipment an ...

  • Eaton Powerware BladeUPS Bar - page 7

    INTRODUCTION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 3 WICHTIGE SICHERHEITSANWEISUNGEN AUFBEWAREN Dieses Handbuch enthält wichtige Hinweise, welche Sie bei der Installation und Wartung des BladeUPS Bar 60 beachten sollten. Bitte lesen Sie alle Anweisungen des H andbuches bevor sie mit dem Gerät arbeiten. Bewaren ...

  • Eaton Powerware BladeUPS Bar - page 8

    INTRODUCTION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 4 INSTRUCCIONES DE SEGURIDAD IMPORTANTES GUARDE ESTAS INSTRUCCIONES Este manual contiene instrucci ones importantes que debe seguir durante la instalación y el funcionamiento del BladeUPS Bar 60. Por favor, lea todas las instrucciones antes de poner en funcionam ...

  • Eaton Powerware BladeUPS Bar - page 9

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 5 Chapter 2 Installation This section explains: S Equipment inspection S BladeUPS Bar 60 setup and installation Inspecting the Equipment If any equipment has been damaged during shipment, keep the shipping cartons and packing materials for the carrier or place of purchase and ...

  • Eaton Powerware BladeUPS Bar - page 10

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 6 Checking the Package Contents Verify that the following items are included: S BladeUPS Bar 60 A six - socket bar with (1) attached terminal block assembly, (1) attached base bracket, and (3) attached mounting brackets S Wireway main housing with (2) attached si ...

  • Eaton Powerware BladeUPS Bar - page 11

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 7 Installation To install the BladeUPS Bar 60: 1. Remove the access cover and terminal block housing from the wireway housing (see Figure 2). Retain the wireway terminal block housing, wireway access cover, and screws. Leave the two side brackets installed on the ...

  • Eaton Powerware BladeUPS Bar - page 12

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 8 4. Install an M6 hex nut onto each of the three wireway studs to secure the wireway to the rear of the rack. Install the first stud in the fourth hole location from the bottom. Do not tighten the nuts. Figure 4 shows the nuts installed. 5. Loosen the three adju ...

  • Eaton Powerware BladeUPS Bar - page 13

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 9 9. Place the ferrite assembly on the floor of the wireway and secure with the supplied tie wrap. Loop the tie wrap through both attachment sites on the wireway floor and through the ferrite assembly. See Figure 4. 10. Note the orientation of the base bracket in ...

  • Eaton Powerware BladeUPS Bar - page 14

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 10 NOTE Verify that the bar is secure as shown in F igure 4. The sheetmetal at the base of the bar should be below the tab on the wireway floor. 12. Secure the bar to the wireway with three M6 × 12 hex bolts. Install the bolts from the front of the rack. See Fig ...

  • Eaton Powerware BladeUPS Bar - page 15

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 11 14. Secure the base bracket to the rack with three M6 × 12 hex bolts. Install the bolts from the rear of the rack. Use a large screwdriver or crowbar to lift the bar in place to align the holes in the base bracket with the holes in the rack. Install the lowes ...

  • Eaton Powerware BladeUPS Bar - page 16

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 12 16. Install two M4 × 8 pan - head screws into the tab on the wireway floor, securing the base of the bar to the wireway. See Figure 7. Torque the screws to 1.7 ± 0.2 Nm (15 ± 2l bi n ) . Rear of Rack Wireway Floor Tab (above bar base sheetmetal) M4 × 8 Pan ...

  • Eaton Powerware BladeUPS Bar - page 17

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 13 17. Using two M6 × 12 hex bolts, secure the left side of the wireway terminal block housing to the rack. See Figure 8. Torque the bolts to 5.1 ± 0.8 Nm (45 ± 7l bi n ) . 18. Using nine M4 × 8 pan - head screws, secure the wireway terminal block housing to ...

  • Eaton Powerware BladeUPS Bar - page 18

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 14 19. Using five M4 × 8 pan - head screws, install the wireway access cover. See Figure 9. Torque the screws to 1.7 ± 0.2 Nm (15 ± 2l bi n ) . M4 × 8 Pan-Head Screws (5 places) Wireway Access Cover Figure 9. Wireway Access Cover Installation 20. Verify the s ...

  • Eaton Powerware BladeUPS Bar - page 19

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 15 21. Using four M5 × 16 hex bolts and four M5 cage nuts, secure the front cover mounting panel to the front of the rack. Verify that the bent edge of the panel is at the top. See Figure 11. Install the lower bolts and cage nuts into the second holes from the b ...

  • Eaton Powerware BladeUPS Bar - page 20

    INSTALLATION EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 16 22. Snap the two front covers into place, as shown in Figure 12. Front Covers (2 pieces) Figure 12. Front Cover Installation ...

  • Eaton Powerware BladeUPS Bar - page 21

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 17 Chapter 3 Specifications This section provides the following specifications: Table 1. BladeUPS Bar 60 Dimensions (WxDxH) 14.0 × 11.3 × 183.8 cm (5.5 ” × 4.4 ” × 72.4 ” ) Depth of Wireway 90.1 cm (35.5 ” ), excluding front covers Weight Bar: 19 kg (42 lb) Wirewa ...

  • Eaton Powerware BladeUPS Bar - page 22

    SPECIFICATIONS EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 18 ...

  • Eaton Powerware BladeUPS Bar - page 23

    EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 19 Chapter 4 Service and Support If you have any questions or problems with the BladeUPS Bar, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a UPS technical representative. United States: 1-800-843-9433 or 1-919-870-3028 Can ...

  • Eaton Powerware BladeUPS Bar - page 24

    SERVICE AND SUPPORT EATON Powerware ® BladeUPS ® Bar Installation Guide S 164201723 Rev P01 20 ...

  • Eaton Powerware BladeUPS Bar - page 25

    ...

  • Eaton Powerware BladeUPS Bar - page 26

    ...

  • Eaton Powerware BladeUPS Bar - page 27

    ...

  • Eaton Powerware BladeUPS Bar - page 28

    *164201723P01* 164201723 P01 ...

Fabricante Eaton Categoría Power Supply

Los documentos del dispositivo Eaton Powerware BladeUPS Bar que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Eaton
- manuales de instrucciones Powerware BladeUPS Bar
- hojas de producto Eaton
- folletos informativos
- o etiquetas energéticas Eaton Powerware BladeUPS Bar
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Eaton Powerware BladeUPS Bar.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Eaton Powerware BladeUPS Bar, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Eaton Powerware BladeUPS Bar. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Eaton Powerware BladeUPS Bar.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Eaton Powerware BladeUPS Bar, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Eaton Powerware BladeUPS Bar. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Eaton Powerware BladeUPS Bar.

El manual de instrucciones completo de Eaton debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Eaton Powerware BladeUPS Bar - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Eaton Powerware BladeUPS Bar, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Eaton Powerware BladeUPS Bar que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Eaton Powerware BladeUPS Bar - que deben facilitarnos los primeros pasos durante el uso de Eaton Powerware BladeUPS Bar
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Eaton Powerware BladeUPS Bar
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Eaton Powerware BladeUPS Bar en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Eaton Powerware BladeUPS Bar?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Eaton Powerware BladeUPS Bar, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Eaton Powerware BladeUPS Bar probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)