-
Aiwa ICT-X40B - page 1
CT-X408 n STEI?EO CAR CASSETTE RECEIVER RADIO-CASSETTE ESTEREOFONICO PARA AUTOMOVIL OWNER’S RECORD For your convenience, record the model number and serial number (you will find them on the right side of yourset) inthespace provided below. Please referto them when you contact your AIWA dealer in case of difficulty. Model NO. ICT-X40B Serinl No. ~ ...
-
Aiwa ICT-X40B - page 2
NOTE Welcome Thank you for your purchasing thisAIWA product. To optimize the performance of this unit, please read through this manual carefully. In addition to this operating instructions manual, be sure to refer to the separate installation and connections manuals as well. PRECAUTIONS ● This unit is designed to be operated on a 12-volt DC negat ...
-
Aiwa ICT-X40B - page 3
TABLE OF CONTENTS FRONT PANEL ....................... .............................. ...................... ......................... ...................... .. .. .. .. . 3 DETACHING AND AITACHING THE FRONT PANEL ......... ............................ ...................... ........... 4 SETTING THE BEEP TONE .................. .................... ...
-
Aiwa ICT-X40B - page 4
FRONTPANEL Display window @H-BASS button @ PWR (power on/off) button @ SEL (select) button @ +/- (audio control) button @EJECT = button @ Caaaette compartment @DIRECTION 4+/- button @BAND button @ CRP (CD changer ready position) button @& (release) button @TUNE Y/A buttons @MUTE button @CD IN jack (3.5-mm dia.) @Preset station buttons I-6 @A. M ...
-
Aiwa ICT-X40B - page 5
DETACHING AND ATTACHING THE FRONT PANEL 1 2 You can detach the front panel from the unit and carry it with you when you leave your car unattended. When you carry the front panel out of your car, use the supplied earring case. Before detaching the front panel, remove the cassette to prevent possible damage to the unit. 1 2 3 Press PWR to turn the un ...
-
Aiwa ICT-X40B - page 6
SETTING THE BEEP TONE The unit is preset at the factory to beep each time you press any button on the front panel except OPEN. You can stop beeping by following the procedure below. [@cl -i EKIl 1 With the unit off, press 1 and 4 at the same time. The “BEEP indication appears. Each time you press them, this function turns on or off. The beep func ...
-
Aiwa ICT-X40B - page 7
RADIO OPERATION 1 32 1 2 3 4 4 Press PWR to turn the unit on. The radio frequency appears. Press BAND to select the band from among FM1, FM2, FM3 and AM. The band indication appears cyclically in order. (FM1, FM2 and FM3 share the same frequency range.) Band Frequency indication indication I I 1 Press (more than 0.5 second) either TUNE 7 orTUNE Ato ...
-
Aiwa ICT-X40B - page 8
PRESETTING STATIONS Press BAND to selects desired bend from among FMI, FM2, FM3 and AM. I FM 1 I r-l /“”-/ / / /.../ /.../. / I Press and hold A.ME for more than 1.5 seconds to activate the automatic preseting function. The six strongest available stations will be stored in memory on the preset station buttons 1 to 6 in order of their signal st ...
-
Aiwa ICT-X40B - page 9
1 1 2 2 Press BAND to selects desired band from among FM1, FM2, FM3 and AM. Press thedeeired txeaet station button. The number of the-pressed preset station button is displayed next to the frequency indication. Active tuning reception control (ATRC) This unit automatically suppresses FM noise caused by varying signal strength resulting from movemen ...
-
Aiwa ICT-X40B - page 10
TAPE PLAYBACK SOUNDADJUSTMENTS Auto reverse function When the end of the tape is reached during playback or fast tape transport, the direction of the tape is automatically reversed, and playback starts again. Tapa direction indications w 8 , Lower side + 24” ‘f ’ Before turning the ignition off Be sure to eject any cassette from the unit be ...
-
Aiwa ICT-X40B - page 11
MUTE button Press this button to temporarily Iowerthe volume. Press it again to restore the previous volume. You can enjoy music with strong bass sound. H-BASS Press H-BASS to obtain powerful bass. The “H BASS” indicator lights up. Each time you press H-BASS, this function turns on or off. CRP (CD changer ready oosition) You can enjoy CD change ...
-
Aiwa ICT-X40B - page 12
CRP (CD changer ready position) 14 2 1 Press PWR to turn the unit on. If a cassette is inserted, remove it to prevent possible damage to the unit. z Press CRP to switch the unit to CRP mode. The “CRP” indicator lights up. s PlayaCDwith yourCDchangersyatem. A Adjuet the volume with +/-. To stop CD changer play 1. Press CRP. 2. Turn off your CD c ...
-
Aiwa ICT-X40B - page 13
MAINTENANCE SPECIFICATIONS Cleaning the front panel When the front panel is soiled, wipe the surface of the panel with a dry and soft cloth. Cleaning the tape head Use a cleaning cassette to clean the playback head and capstans approximately once a month. If the playback head is dirty, the high tones may not be reproduced properly. Cleaning the con ...
-
Aiwa ICT-X40B - page 14
...
-
Aiwa ICT-X40B - page 15
...
-
Aiwa ICT-X40B - page 16
88-KTD-903-01 9801 O9BTM-O)( AIWA CO.,LTD. ...
¿Tienes una pregunta acerca de Aiwa ICT-X40B?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Aiwa ICT-X40B, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Aiwa ICT-X40B probablemente compartirá una forma de solucionarlo.