-
Honeywell 6000-QS - page 1
Dolphin ™ 6000 Quick Start Guide 6000-QS Rev A 5/11 Aller à www.honeywellaidc.com pour le français. Vai a www.honeywellaidc.com per l'italiano. Für Deutsch gehe zu www.honeywellaidc.com . Ir a www.honeywellaidc.com para español. Para Português, acesse www.honeywellaidc.com.br . Перейти на русскоязычный сайт www ...
-
Honeywell 6000-QS - page 2
Out of the Bo x Verify that your carton contains the following items: • Dolphin 6000 mobile terminal • Main battery pack (3.7V, Li-ion) • A C p o w e r s u p p l y • Q u i c k S t a r t G u i d e Note: If you ordered accessories f or your terminal, verify that they are also included with the order. Be sure to keep the original packagi ng in ...
-
Honeywell 6000-QS - page 3
Front P anel Shift TAB FN BKSP ENT FN F1 1 g hi F4 4 abc F2 2 def F3 3 mno F6 6 wxyz F9 9 SPACE ESC # jkl F5 5 pqrs F7 7 tuv F8 8 F10 0 Front Speaker Indicator LED Touch Panel Display SCAN Key Blue FN Key Power Key Microphone Orange FN Key Navigation Keys Volume Control Buttons Picture/Video Button I/O Connector ...
-
Honeywell 6000-QS - page 4
Bac k Pa nel MicroSD Memory Card Socket Laser/Scan Engine Rear Speaker Camera Flash Color Camera Battery Door SIM Card Socket Stylus Tether/ Lanyard Slot Battery Door Latch ...
-
Honeywell 6000-QS - page 5
Ke yboard 29-key Alphanumeric K eyboar d Shift TA B FN BKSP ENT FN F1 1 g hi F4 4 abc F2 2 def F3 3 mno F6 6 wxyz F9 9 SPACE ESC # jkl F5 5 pqrs F7 7 tuv F8 8 F10 0 ...
-
Honeywell 6000-QS - page 6
Installing the Battery Pac k The Dolphin 6000 is sh ipped with the battery packaged separately from the terminal. Perform the follo wing steps to install the battery. 1. Slide the latch to unlock the battery door. 2. Open the battery door. 3. Insert the battery into the battery well with the contacts facing the front of the unit. 4. Re-install the ...
-
Honeywell 6000-QS - page 7
Note: Install the battery door before powering the terminal. 5. Connect the terminal to one of the Dolphin 6000 charging peripherals to charge the battery pack. Removing the Battery P ac k Perform the following steps to remove the battery. 1. Slide the latch to unlock the battery door. 2. Open the battery door. 3. Remove the battery by lifting the ...
-
Honeywell 6000-QS - page 8
Charging the Dolphin Dolphin terminals ship with the ba ttery significantly discharged of power. Charge the battery pack with a Dolphin charging device for a minimum of 4 hours before initial use. ...
-
Honeywell 6000-QS - page 9
HomeBase HomeBase Back P anel HomeBase Battery Well LED Indicator s Green Full (completed charge) Red Fast charge Orange Pre-charge (low battery status) Orange - Blinking Battery cannot be charged Off No battery, fault or over temperature AUX Battery Well AUX Battery Charge State LED DC Power Jack USB Port Serial Port ...
-
Honeywell 6000-QS - page 10
Charging/Comm unication Cable COMM Cable Power Adapter Cable Host Device USB Connector ...
-
Honeywell 6000-QS - page 11
T urning De vice On/Off To turn the Dolphin 6000 terminal on: 1. Press and hold the Power button for 3 seconds. To turn the terminal off, press the Power button for 5 seconds. 2. Tap OK to shutdown. Suspending/Resuming T erminal To put the device into Suspend mode when the terminal is powered on: 1. Press and release the power button. 2. To resume ...
-
Honeywell 6000-QS - page 12
ActiveSync Comm unication To synchronize data (e.g., e-mail, contacts, and calendar between the terminal and the host workstation (PC): 1. ActiveSync® (version 4.5 or higher) or Windows® Mobile Device Center (WDMC) must be installed on your PC. You can download the most current vers ion of ActiveSync or WDMC from the Microsoft Web site (http://go ...
-
Honeywell 6000-QS - page 13
Installing a Memory Card 1. Power down the terminal. 2. Unlock and remove the battery door. 3. Remove the battery. 4. Slide the latch toward the top of the terminal to unlock the SIM card. 5. Lift the SIM card latch to reveal the SIM card. 6. Remove the SIM card to reveal the memory card latch. 7. Unlock the memory card latch by sliding the latch a ...
-
Honeywell 6000-QS - page 14
Installing a SIM Card 1. Power down the terminal. 2. Unlock and remove the battery door. 3. Remove the battery. 4. Slide the latch toward the top of the terminal to unlock the SIM card. 5. Lift the SIM card latch. 6. Insert the SIM card into the SIM card socket. Note: Make sure the interface on the card is connected to the SIM card interface in the ...
-
Honeywell 6000-QS - page 15
Using the Scan Engine Point the aiming beam at a bar code. The aiming beam must align with the bar code for the best resu lts. Holding the terminal between 4-10 inches (10-25 cm) from a bar code is recommended. Note: The touch panel display can be activated by using the stylus (included with the terminal) or your finger. To activate the display, op ...
-
Honeywell 6000-QS - page 16
Aiming Beam The aiming beam is narrower when you hold the terminal closer to a bar code and the aiming beam is wi der when you hold it farther from the bar code. The aiming beam must be aimed closer to symbologies that have smaller bars or elements (mil size ). The aiming beam must be aimed farther from symbologies that have la rger bars or element ...
-
Honeywell 6000-QS - page 17
T echnical Assistance Contact information for technical s upport, product service, and repair can be found at www.honeywellaidc.com . User Documentation For localized versions of this doc ument, and to download the User’s Guide, go to www.honeywellaidc.com . Pa te n ts For patent information, please refer to www.honeywellaidc.com/ patents . Limit ...
¿Tienes una pregunta acerca de Honeywell 6000-QS?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Honeywell 6000-QS, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Honeywell 6000-QS probablemente compartirá una forma de solucionarlo.