-
Henny Penny OFE- 290 - page 1
Model OFE- 290 3-1. OPERA TING COMPONENTS POWER/PUMP Switch A three way switch with center OFF position; move the switch to the position marked POWER to operate the fryer; move the switch to the position marked PUMP to operate the filter pump; certain conditions must be met prior to operation of the filter pump; these conditions are covered later i ...
-
Henny Penny OFE- 290 - page 2
Model OFE- 290 3-1. OPERA TING COMPONENTS (Continued) High Limit This high temperature control senses the temperature of the shortening; if the temperature of the shortening exceeds 450°F (230°C), this control will open and shut off the heat to the frypot; when the temperature of the shortening drops to a safe operation limit, the control must be ...
-
Henny Penny OFE- 290 - page 3
Model OFE- 290 3-4. SWITCHES AND Refer to image at end of this section. INDICA T ORS Product Selection Buttons Select the number of heads, or product, to be cooked by pressing the button below the menued item; shortening will then heat to drop temperature of that item Pressing the same button again begins the Cook Cycle; the display changes from ? ...
-
Henny Penny OFE- 290 - page 4
Model OFE- 290 EXIT COOL Button After cooking, or filtering the shortening, the temperature automati- cally goes into the Cool Mode, which keeps shortening at a lower temperature; this temperature extends the shortening life and minimizes the time to heat the shortening for the next Cook Cycle; EXIT COOL button must be pressed to heat up to setpoin ...
-
Henny Penny OFE- 290 - page 5
Model OFE- 290 3-5. FILLING OR ADDING SHOR TENING The shortening level must always be above the heating elements when the fryer is heating and at the frypot level indicators on the r ear of the frypot (Figur e 3-3). Failur e to follow these instructions could r esult in a fir e and/or damage to the fryer . When using solid shortening, it is r ecomm ...
-
Henny Penny OFE- 290 - page 6
Model OFE- 290 3-6. BASIC OPERA TION Follow the procedure below on the initial start-up of the fryer , and each time the fryer is brought from a cold, or shut down condition, back into operation. These are basic, general instructions. Be sure to follow KFC’ s Standards Library when operating the fryer . 1. Make sure the shortening is filled to th ...
-
Henny Penny OFE- 290 - page 7
Model OFE- 290 3-6. BASIC OPERA TION 4. Allow fryer to heat until digital display shows “DROP”. (Continued) (Press the EXIT COOL button if the display shows COOL”) The heat cycles on and off approximately 10 degrees before the setpoint temperature, to help prevent overshooting the setpoint temperature. (proportional control) 5. Slide racks of ...
-
Henny Penny OFE- 290 - page 8
Model OFE- 290 3-7. CARE OF THE SHOR TENING FOLLOW THE INSTRUCTIONS BELOW T O A VOID SHOR TENING OVERFLOWING THE FR YPOT , WHICH COULD RESUL T IN SERIOUS BURNS, PERSONAL INJURY , FIRE, AND/OR PROPERTY DAMAGE. 1. T o protect the shortening when the fryer is not in immediate use, the fryer should be put into the Cool Mode. 2. Frying breaded products ...
-
Henny Penny OFE- 290 - page 9
Model OFE- 290 3-8. FIL TERING INSTRUCTIONS (continued) ONL Y FIL TER WHEN “COOL” IS DISPLA YED. FAILURE T O DO SO CAN RESUL T IN SHOR TENING OVERFLOWING THE FR YPOT , CAUSING SERIOUS BURNS, PERSONAL INJUR Y , FIRE,AND/OR PROPER TY DAMAGE . High volume cooking could cause the cold zone to fill quicker with cracklings and cleaning may be require ...
-
Henny Penny OFE- 290 - page 10
Model OFE- 290 3-8. FIL TERING 5. Scrape cracklings and crackling ring from frypot and discard. INSTRUCTIONS Do not let cracklings drain into filter drain pan. These crack- (Continued) lings can cause a burned taste in gravy . W ipe all surfaces with a clean damp towel. If water drops into cold zone, dry with towel before pumping shortening back in ...
-
Henny Penny OFE- 290 - page 11
Model OFE- 290 3-10. CLEANING THE FR YPOT After the initial installation of the fryer , as well as before every change of shortening, the frypot should be thoroughly cleaned as follows: 1 . T urn the POWER/PUMP switch to OFF positioin, and unplug unit from wall receptacle. Moving the fryer or filter drain pan while containing hot shortening is not ...
-
Henny Penny OFE- 290 - page 12
Model OFE- 290 3-1 1. FIL TER PUMP MOT OR The filter pump motor is equipped with a manual reset button, PROTECTOR-MANUAL located on the rear of the motor , in case the motor overheats. If RESET motor won’t run, wait about 5 minutes before attempting to reset this protective device to allow motor to cool. Remove the access panel on the left side p ...
-
Henny Penny OFE- 290 - page 13
Model OFE- 290 3-14. PROGRAMMING 1. Press and hold the FUNCTION button for two seconds. “REG PROGRAM” shows in the display , followed by “CODE”. 2. Press the code1-2-3. “SELECT PRODUCT” scrolls across the display . If no buttons are pressed, within approximately 1 minute while in the Program Mode, the controls will revert back to the Co ...
-
Henny Penny OFE- 290 - page 14
Model OFE- 290 7. After the load compensation, press and release the FUNC- TION button. “PROP” and “CONTROL” shows on the left side of the display and the factory preset proportional control temperature shows on the right side of the display . 8. After the proportional control, press and release the FUNCTION button. “ALM 1” and “TIME? ...
-
Henny Penny OFE- 290 - page 15
Model OFE- 290 3-14. PROGRAMMING (continued) 13 . After the end-of-cycle point is set, press and release the FUNCTION button. “HEAD” flashes on the left side of the display and a number shows on the right side of the display . The number on the right, is the number of head of chicken to be cooked at one time, when that product button is pressed ...
-
Henny Penny OFE- 290 - page 16
Model OFE- 290 3-15. SPECIAL PROGRAM MODE (Continued) Factory Presets (F/C, Gas/Electric, Speaker V olume, Speaker Fr equency , Codes, Initialize System) 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 3 tim ...
-
Henny Penny OFE- 290 - page 17
Model OFE- 290 3-15. SPECIAL PROGRAM MODE (Continued) T ech I/O Mode 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 4 times until “TECH I-O” shows in the display . 2. When “CODE” shows in the displa ...
-
Henny Penny OFE- 290 - page 18
Model OFE- 290 3-16. SPECIAL PROGRAM Heat Control MODE (Continued) 1. Press and hold the FUNCTION button for two seconds until “REG PROGRAM” shows in the display . As soon as “REG PROGRAM” shows in the display , press and release the FUNCTION button 6 times until “HEA T CNTRL” shows in the display . 2. When “CODE” shows in the displ ...
¿Tienes una pregunta acerca de Henny Penny OFE- 290?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Henny Penny OFE- 290, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Henny Penny OFE- 290 probablemente compartirá una forma de solucionarlo.