-
StarTech.com ARMDUAL - page 1
Manual Revision: 06/16/2014 For the most up-to-date information, please visit: www.startech.com ARMDU AL Desk Mount Ar ticulating Dual Monitor Arm with Cable Management & Height A djust *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr .startech.com ES: Guía del usuario - es.sta ...
-
StarTech.com ARMDUAL - page 2
Instruction Manual FCC C ompliance Statemen t This equipment has been tested and f ound to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules . These limits ar e designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates , uses and can radiate ...
-
StarTech.com ARMDUAL - page 3
Instruction Manual i T able of C ontents Introduction ............................................................................................ 1 Packaging Conten ts ................................................................................................................................. 1 Product Diagram ................................. ...
-
StarTech.com ARMDUAL - page 4
Instruction Manual 1 Introduction Packaging C ontents ...
-
StarTech.com ARMDUAL - page 5
Instruction Manual 1 P roduct Diagram ...
-
StarTech.com ARMDUAL - page 6
Instruction Manual 2 Installation W ARNING! It is the installer ’ s responsibility to ensure that the combined w eight of all components does not exc eed the maximum weight capacity 13.6 kg (30 lbs) of the mounting arm. Con verting the Desk Clamp to a Grommet Clamp The Dual Monitor Arm can be clamped to a desk / table, or mounted thr ough a gromm ...
-
StarTech.com ARMDUAL - page 7
Instruction Manual 3 3. Using the 4 hex screw s removed in Step 2, install the Grommet Pla te (7) to the base of the pole. 4. Remove the screw and 2 w ashers shown using a Phillips screwdriver to disconnect the threaded shaft from the base of the clamp, then slide the plat e back onto the shaft. Finished Gr ommet Clamp: ...
-
StarTech.com ARMDUAL - page 8
Instruction Manual 4 Desk / Grommet Mounting 1. Adjust the height of the Desk Clamp (3) to t y our desk sur face (if applicable). 2. Place the 4 Plastic Gasket Cushions (13) as sho wn. ...
-
StarTech.com ARMDUAL - page 9
Instruction Manual 5 3. Desk Clamp: Place the Desk Clamp (3) opening around the edge of y our desktop in your desired location and tigh ten by hand to secure. Ensure tha t the Desk Clamp is making full contact with the desk sur face. 4. Loosen the collar on the support post and adjust to the desired height. Grommet Clamp: Place the base of the unit ...
-
StarTech.com ARMDUAL - page 10
Instruction Manual 6 5. Slide the DEK (12) onto the support post so that it rests on the collar . Once adjusted to the desired height, tight en into place using the 2.5mm Allen Wrench (10). Attaching the Display s 1. Car efully place your display face down on a protective surface to access the mounting points. 2. Depending on the depth of the mount ...
-
StarTech.com ARMDUAL - page 11
Instruction Manual 7 3. Using a Phillips screw driver , tighten the screws until the bracket is rmly attached to the back of the display . W ARNING! Do not over-tighten the scr ews and stop immediately if you encounter resistance to av oid damage to your display . Ensure that all spacers and screws being used are the same length and thread type. ...
-
StarTech.com ARMDUAL - page 12
Instruction Manual 8 Attaching the L CD Arm Assembly 2. Tighten the set scr ew using the 2.5mm Allen W rench ( 10 ). 1. Slide the L CD Arm Assembly ( 1 or 2 ) down onto the DEK ( 12 ). ...
-
StarTech.com ARMDUAL - page 13
Instruction Manual 9 3. Place the Co ver (11) over the mounting post and insert 1 x M6x12mm Phillips Screw (16) with 1 x Plastic Washer (15) . Tighten using a Phillips screwdriver . 4. Repeat for the other side . ...
-
StarTech.com ARMDUAL - page 14
Instruction Manual 10 Cable Management Note: When attaching cables and routing thr ough the cable management channels, ensure that you leav e enough slack to avoid stretching / pulling out the cables when moving the arm. 1. Connect your cables to y our displays and position the mounting arm in its fully extended position to ensure that the cables y ...
-
StarTech.com ARMDUAL - page 15
Instruction Manual 11 Adjusting L CD Arm Resistance W ARNING! For ced movement of the L CD Arms or Mount Brackets without loosening the screws may damage the pr oduc t or the mounted displays . Always support your display from underneath when making any adjustments to the L CD Arms or Mount Brackets to avoid damage to the display . Note: F or all a ...
-
StarTech.com ARMDUAL - page 16
Instruction Manual 12 T o increase / decrease the pan / swing resistance, adjust the set scr ew located on the top of the Mount Bracket joint, using the 4mm Allen Wrench (9). T o increase / decrease the swivel resistance on either of the elbow join ts of the articulating LCD Arms, adjust the set scr ews indicated below , using the 2.5mm Allen Wrenc ...
-
StarTech.com ARMDUAL - page 17
Instruction Manual 13 Specications W eight Capacity 30 lbs (13.6 kg) Max Display Size 24” VESA Compatibility 75x75 mm and 100x100 mm Maximum Extension 18.66 in (474 mm) Maximum Mounting Surface Thickness 3 in (75 mm) ...
-
StarTech.com ARMDUAL - page 18
Instruction Manual 14 T echnical Suppor t StarT ech.com ’ s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your pr oduct, visit ww w .startech.com/suppor t and access our comprehensive selection of online tools , documentation, and downloads. For the la test drive ...
-
StarTech.com ARMDUAL - page 19
Hard-to-nd made easy . At StarT ech.com, that isn’t a slogan. It’ s a promise. StarT ech.com is your one-stop source for every connectivity par t you need. Fr om the latest technology to legacy products — and all the parts that bridge the old and new — we can help you nd the parts that connect your solutions. We make it easy t o locat ...
¿Tienes una pregunta acerca de StarTech.com ARMDUAL?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con StarTech.com ARMDUAL, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con StarTech.com ARMDUAL probablemente compartirá una forma de solucionarlo.