-
Emerson kf220tzg00 - page 1
Net Weight: 33.7 Lbs. Part No. F40BP73070000 Form No. BP7307 READ AND SA VE THESE INSTRUCTIONS KF220TZG00 T anner y Bronze ¨ Housing with Gold Accents and Dar k Cher r y/Walnut Blades KF220GLZ00 Gilded Silv er with Natural Cher r y/ Mahogany Blades KF220A GW00 Aged Walnut with T eak/Mahogany Blades LARISSA Ceiling Fan Owner's Manual Emerson F ...
-
Emerson kf220tzg00 - page 2
W ARNING: T o avoid fire, shock, and serious personal injury , follow these instructions. Safety Instructions 1. Read your owner ’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidental ...
-
Emerson kf220tzg00 - page 3
3 This Manual Is Designed to Make it as Easy as Possible for Y ou to Assemble, Install, Operate and Maintain Y our Ceiling Fan Do not install or use fan if any part is damaged or missing. Call T oll-Free: 1-800-654-3545 ! W ARNING This product is designed to use only those parts supplied with this product and/or any accessories designated specifica ...
-
Emerson kf220tzg00 - page 4
4 q. One loose parts bag containing: 1. T wo 1-1/4” threaded studs 2. T wo knurled knobs 3. T wo lockwashers 4. Seven wire connectors 5. One clevis pin/hairpin clip assembly 6. Eleven 1/4-20 x 13mm oval head screws 7. Sixteen 10-24 x 8mm pan head screws 8. Sixteen flat washers 9. Three 8-32 x 7mm pan head screws 10. T wo 1/8-27 nuts 1 1. One 1/8- ...
-
Emerson kf220tzg00 - page 5
5 Y our new ceiling fan will require a grounded electrical supply line of 120 volts AC, 60 Hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 pounds. General Y our Emerson ceiling fan comes supplied with a Fan/Light W all Control which consists of a wall control (transmitter) and a remote ...
-
Emerson kf220tzg00 - page 6
5. Gently snug all flange screws to the motor hub, working around the hub in a clockwise sequence. Next, securely tighten all flange screws, again working in a clockwise sequence. Failure to follow this procedure could result in fan wobble. This completes the blade installation. NOTE: If you wish to assemble your ceiling fan without the lower light ...
-
Emerson kf220tzg00 - page 7
8. Carefully rest the decorative ring/light fitter/switch cup assembly on the fan blades, then engage the connector of the switch cup assembly with the motor connector (Figure 4). The two connectors are keyed and color-coded and must be mated correctly (color-to- color) before they can be engaged. Make sure the connectors are engaged properly . 9. ...
-
Emerson kf220tzg00 - page 8
8 12. Unscrew the two upper setscrews (Figure 8) until they clear the inside of the motor coupling. Then separate, untwist and unkink the three 80” motor leads. Route the motor lead wires through the downrod. Align the clevis pin holes in the downrod with the holes in the motor coupling. Install the clevis pin and secure with the hairpin clip (Fi ...
-
Emerson kf220tzg00 - page 9
9 18. Place the ceiling cover over the downrod. Then reinstall the hanger ball (Figure 10) on the downrod as follows. Route the three 80” motor leads through the hanger ball and slide the hanger ball over the downrod. Position the pin through the two holes in the downrod and align the hanger ball so the pin is captured in the groove in the top of ...
-
Emerson kf220tzg00 - page 10
10 2. Carefully lift the fan and seat the hanger ball/downrod assembly on the hanger bracket that was just attached to the outlet box (Figure 13). Be sure the groove in the ball is lined up with the tab on the hanger bracket (Figure 12). 1. Securely attach the hanger bracket to the outlet box using the two screws supplied with the outlet box (Figur ...
-
Emerson kf220tzg00 - page 11
1. Position the supply wires to the left side of the outlet box (Figure 14); position the fan wires to the right side. Partially insert the remote control receiver (flat side up) until one end rests on the hanger ball as shown in Figure 14. NOTE: Make all wiring connections using wire connectors (supplied). Make sure that all connections are tight, ...
-
Emerson kf220tzg00 - page 12
12 7. Screw in three 40-watt (maximum) candelabra bulbs in the light fitter sockets (Figure 17). Carefully place the lower glass over the light fitter threaded nipple. Be sure the glass is firmly seated in the decorative ring, then secure in place using a rubber washer , metal washer , and nut (washers and nut are supplied). 8. Place the decorative ...
-
Emerson kf220tzg00 - page 13
Installation of W all Control SINGLE-POLE INST ALLA TION (Figure 19) 1. Disconnect power at circuit breaker or remove fuse. 2. Remove faceplate and screws from existing wall control. Pull control out from the wall box. Determine the “hot” wire and the “load” wire and disconnect these wires from control. Do not attempt to disconnect any wire ...
-
Emerson kf220tzg00 - page 14
3. Before installing wall control, place wall control in “OFF” mode by pushing “ON/OFF” switch to the “OFF” position. 4. Install a wall control in the wall box containing the “hot” wire first. Connect the black wire of the wall control to the “hot” wire. Securely connect wires with wire connectors supplied. 5. Connect one black ...
-
Emerson kf220tzg00 - page 15
9. Place the second wall control into the wall box. Screw in place and install decorator style faceplate (included). Leave switch in “OFF” mode until fan installation is completed. 10. Refer to page 5 and complete the ceiling fan installation . ST ANDARD WIRING FOR EXISTING 3-WA Y CONTROL 15 HOT BLK F AN/LIGHT WALL CONTROL BLK TRA VELER WIRES B ...
-
Emerson kf220tzg00 - page 16
16 Do not use water when cleaning your ceiling fan. It could damage the motor or the blades and create the possibility of an electrical shock. ! W ARNING The use of any other control not specifically approved for this fan could result in fire, shock and personal injury . ! W ARNING This product is designed to use only those parts supplied with this ...
-
Emerson kf220tzg00 - page 17
17 T rouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not 1. Fuse or circuit breaker 1. Check main and branch start. blown. circuit fuses or circuit breakers. W ARNING: Make sure main power is turned off. 2. Loose power line 2. Check line power connections connections to the fan. to fan. 3. Fan/Light W all Control is OFF. 3. Turn ...
-
Emerson kf220tzg00 - page 18
Repair Parts 3 2 1 5 9 8 12 10 30 11 23 6 14 15 13 24 25 27 35 EMERSON ® HI MED LOW FAN OFF LIGHT ON OFF 34 4 18 20 22 21 19 7 26 16 17 14 28 31 32 33 29 Before discarding packaging material, be certain all parts have been removed. HOW TO ORDER REP AIR P ARTS WHEN ORDERING REP AIR P ARTS, AL WA YS GIVE THE FOLLOWING INFORMA TION: • P ART NUMBER ...
-
Emerson kf220tzg00 - page 19
Part Numbers Key Model No. Model No. Model No. N o . Description KF220AGW00 KF220GLZ00 KF220TZG00 * Hanger Pack, Consisting of: 761655-56 761655-55 761655-54 1 Hanger Bracket — — — 2 Hanger Ball — — — 3 Downrod — — — * Parts Bag, Containing: 763047-2 763047-1 763047 4 Wire Connector (7) — — — 5 Threaded Stud, 8-32 x 1-1/4” ...
-
Emerson kf220tzg00 - page 20
LIMITED WARRANTY What The War ranty Covers: This warranty covers the motor and the other components and accessories of your Emerson Electric Co. ceiling fan against all defects in workmanship and materials. Y ou must be the original purchaser or user of the product to be covered. What The Period Of Coverage Is: As it applies to the motor , this war ...
¿Tienes una pregunta acerca de Emerson kf220tzg00?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Emerson kf220tzg00, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Emerson kf220tzg00 probablemente compartirá una forma de solucionarlo.