Español dropdown-ico

Manual de instrucciones Wavetronix SMARTSENSOR 105

36 de páginas 0.63 mb
Descargar

Pasar a la página of 36

Summary
  • Wavetronix SMARTSENSOR 105 - page 1

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 SmartSensor 105 Installation Guide Wavetronix LLC 380 S. Technology Ct. Lindon, Utah 84042 USA Voice: (801) 764-0277 Fax: (801) 764-0208 Web: www.wavetronix.com E-mail: support@wavetronix.com © 2007 Wavetronix LLC. All Rights Reserved. SmartSensor, Smar tSensor Manager, Click!, Wa vetr onix, a ...

  • Wavetronix SMARTSENSOR 105 - page 2

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 2 Contents Typographical Conventions ................................................................................................ 3 Product Notifications .......................................................................................................... .3 Introduction .......... ...

  • Wavetronix SMARTSENSOR 105 - page 3

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 3 Typographical Conventions Before you start using this guide, it is important to understand the terms and typographical conventions used in the documentation. Bold Text Bolded text represents items you must select, such as menu options, command buttons, or items in a list. Product Notifica ...

  • Wavetronix SMARTSENSOR 105 - page 4

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 4 Risk of Electrical Shock An authorized electrical technici an should perform installation and operation of this unit. Persons other than authorized and approved electrical technicians should NOT attempt to c onnect this unit to a power supply and/or traffic control cabine t, as there is a ...

  • Wavetronix SMARTSENSOR 105 - page 5

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 5 Introduction The Wavetronix SmartSensor utilizes pate nted Digital Wave Radar™ technology to detect lane occupancy, traffic volume and aver age speed in up to ei ght lanes of traffic simultaneously. Classified as Frequency M odulated Continuous Wave (FMCW ) radar, SmartSensor collects d ...

  • Wavetronix SMARTSENSOR 105 - page 6

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 6 Installing the SmartSensor Installing the SmartSensor involves seven simple steps: 1. Attaching the mounting bracket to the pole; 2. Applying silicon dielectric compound; 3. Attaching the SmartSenso r to th e mounting bracket; 4. Aligning the SmartSensor; 5. Connecting SmartSensor cable t ...

  • Wavetronix SMARTSENSOR 105 - page 7

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 7 Table 1 – Mounting Height Guidelines ...

  • Wavetronix SMARTSENSOR 105 - page 8

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 8 2. Applying Silicon Dielectric Compound 1. Take the tube of Silicon Dielec tric Com pound and tear off the tab. 2. Squeeze about 25% of the silicon into the connector at the base of the SmartSensor as shown in Figure 2. Be sure to wipe off any excess compound. Figure 2 – Applying Silico ...

  • Wavetronix SMARTSENSOR 105 - page 9

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 9 2. Adjust the side-to-side angle to within approximately ±2° of perpendicular to the flow of traffic. 3. Tighten mounting bracket bolts. 5. Connecting the SmartS ensor Cable to SmartSensor Figure 4 – Attached Cable 1. Attach the cable connector to the 25-pin connector at th e base of ...

  • Wavetronix SMARTSENSOR 105 - page 10

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 10 6. Connecting SmartSensor to Power and Communication Devices A typical sensor installati on requires a pole-mount box cont aining surge protection and connections for power and communications. Smar tSensor is compatible w ith all standard control cabinets; a table describing the Sm artSe ...

  • Wavetronix SMARTSENSOR 105 - page 11

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 11 Figure 5 – Short Distan ce Cabl e Run Long Cable Run (41-100 feet) A long cable installation include s any installation with a Sm artSensor cable longer than 40 feet. Follow the steps below to correctly add surge protection to a long cable run (see Figure 6): 1. Connect the SmartSensor ...

  • Wavetronix SMARTSENSOR 105 - page 12

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 12 Figure 6 – Long Distance Cable Run ...

  • Wavetronix SMARTSENSOR 105 - page 13

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 13 The Click! 200 has 12 screw terminal conn ections on both the top and the bottom (see Figure 7). The screw terminals on the top of the module are surge protected: Back The back four terminals consist of one +DC power, -DC and two surge ground connections; Middle The middle four terminals ...

  • Wavetronix SMARTSENSOR 105 - page 14

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 14 Wire the SmartSensor ca ble to the Click! 200 according to Table 2: Table 2 – Click! 200 Connections NOTE : See Appendix F for a description of how to wire the Click! 200 using the old SmartSensor cable as well as for a cable connector pin-out diagram . 7. Configuring SmartSensor with ...

  • Wavetronix SMARTSENSOR 105 - page 15

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 15 a telephone number); or Ethe rnet (requires a TCP/IP a ddress). Select the radio button of the appropriate connection method and click OK. If you select Serial Connection a nd SmartSensor Manager cannot find a SmartSensor connected to the serial port, then a “Sm artSens or was not dete ...

  • Wavetronix SMARTSENSOR 105 - page 16

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 16 Manual Configuration If the sensor is unable to automatically configure itself to your satisfaction, you can manually configure it by adding, removing or ad justing lanes, lane dividers and lane centers. Figure 8 – Automati c and Manu al Modes 1. With the Lane Configuration page open, ...

  • Wavetronix SMARTSENSOR 105 - page 17

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 17 The cursor will change from an arro w to a hand when it is positioned over a “d raggable” line. Lane centers (pink lines) only appear when the cursor is placed directly over them. Figure 9 – Adjusting L anes Also, you will notice that shoulders, dividers, or centers cannot be dragg ...

  • Wavetronix SMARTSENSOR 105 - page 18

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 18 Remove Lane The Remove Lane button allows users to remove en tire lanes by moving the m ouse cursor arrow to the desired lane. When the arrow changes to a hand, click the left m ouse button and the selected lane will disappear. Construct and Remove Road To insert a new road, click on the ...

  • Wavetronix SMARTSENSOR 105 - page 19

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 19 To do this, press the Reverse Direction button and move the cursor over the lane you wish to change. Once the cursor is in place, the cursor will again change from an arrow to a hand and a tiny arrow will appea r below th e hand to indicate the current direction of that lane. Figure 10 ? ...

  • Wavetronix SMARTSENSOR 105 - page 20

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 20 Figure 11 – Editing Lane Names To do this, click on the Edit Lane Name button and an Edit Lane Names window will appear (see Figure 11). Highli ght the current lane name by double clicking on it with the mouse, and then type in the lane’s new al pha-numeric identification of up to ei ...

  • Wavetronix SMARTSENSOR 105 - page 21

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 21 Undoing Manual Changes Unsaved changes may be undone without repea ting the manual confi guration process. Click on the Undo button found below the manual tool bu ttons (see Figure 12). This tool retrieves the last saved configuration from the SmartSensor, effectively undoing any unsaved ...

  • Wavetronix SMARTSENSOR 105 - page 22

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 22 Figure 14 – Lane Configuration Page in Manual Mode Figure 15 – Traffic/E v ent Data View Mode ...

  • Wavetronix SMARTSENSOR 105 - page 23

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 23 A window will appear indicating that the changes are b eing sa ved to the SmartSensor. After the changes have been saved, SmartS ensor Manager will au tomatically change from Lane Configuration to Traffic/Event Data View mode. Figures 14 an d 15 illustrate the differences between these t ...

  • Wavetronix SMARTSENSOR 105 - page 24

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 24 Appendix A – SmartSensor Specifications Operating Frequency: 10.525 GHz (X-band) Detection Zones: Up to 8 traffic lanes simultaneously Detection Range: 60 m (197 ft.) Measured Quantities: Speed, occ upancy, volume, presence Communications: RS-232 an d RS-4 85 connection Power: 7.5 watt ...

  • Wavetronix SMARTSENSOR 105 - page 25

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 25 Appendix B – Cable Connector Definitions The SmartSensor cable is com prised of three gr oups of wires. Each group contains color- coded wires accompanied by a drain wire and surrounded by a shield. The following table details the pin out of th e cable and the appropriate conne ction i ...

  • Wavetronix SMARTSENSOR 105 - page 26

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 26 Figure 16 - SmartSensor SS105 Plug Connector Socket Assignment as seen from the solder cup side of th e c onne cto r. ...

  • Wavetronix SMARTSENSOR 105 - page 27

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 27 Appendix C – RS-232 Communication Communication between the SmartSensor and PC can be established using the RS-232 DTE specifications, along with the use of a Null Modem cable and the standard 9-pin “D” male connector. Please use th e followi ng guidelines for connec ting the Smart ...

  • Wavetronix SMARTSENSOR 105 - page 28

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 28 Figure 18 – Connecting a M odem to the SmartSensor Figure 19 – Rear view of RS-2 3 2 DB9 seri al connect or ...

  • Wavetronix SMARTSENSOR 105 - page 29

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 29 Appendix D – RS-485 Communication RS-485 communication between the SmartSenso r and PC may be established by using the SeaLink +485 model #2102 RS-485 to USB converter by SeaLevel, along with the standard 25-pin “D” female conne ctor with the following pin out: 1: No Connection (N/ ...

  • Wavetronix SMARTSENSOR 105 - page 30

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 30 Appendix F – Old Cable Connector Definitions The previously used SmartSensor cable is com p rised of six twisted pa irs of wire. Each pair is comprised of a black and a red wi re, accompanied by a drain wire and surroun ded by a shield. A numeric label (1 through 6) iden tifies each pa ...

  • Wavetronix SMARTSENSOR 105 - page 31

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 31 Figure 20 - Click! 200 Wiri ng (Ol d ) See Figure 21 for a diagram of the previously used SmartSensor cable’s 25-pin socket assignment. The codes listed in the diagram ar e to be used to solder wires into the bac k of the plug where the le tters represe nt the individual solder cups. ...

  • Wavetronix SMARTSENSOR 105 - page 32

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 32 Figure 21 – Old SmartSensor SS105 Plug Connect or Sock et Assignment as seen from the solder cup side of the connector. ...

  • Wavetronix SMARTSENSOR 105 - page 33

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 33 Communication between the SmartSensor and PC can be established using the RS-232 DTE specifications, along with the use of a Null Modem cable and the standard 9-pin “D” male connector. P lease use the followi ng guidelines for connec ting the Sm artSens or cable to the serial connect ...

  • Wavetronix SMARTSENSOR 105 - page 34

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 34 Table 7 – Belden 9331 (Old Cable) Conversions ...

  • Wavetronix SMARTSENSOR 105 - page 35

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 35 Appendix G – Cable Lengths The following recommendations allow the us er to provide reliable power to the SmartSensor. The SmartSensor cable’s red a nd black wires provide a 20 AWG wire pair. The other pairs on the SmartSensor cable are 22 AW G and are normally used for communication ...

  • Wavetronix SMARTSENSOR 105 - page 36

    SmartSensor 105 User Guide – Wavet ronix LLC 9/20/07 - - 36 mounted next to the sensor. In this case, the homerun connection establishes one RS-485 channel over the normal white/blue wire pair and another R S -485 channel over the yellow/violet wire pair. An additional Click ! 304 is needed to convert the data sent o ver the yellow/violet wire pa ...

Fabricante Wavetronix Categoría Home Security System

Los documentos del dispositivo Wavetronix SMARTSENSOR 105 que obtenemos del fabricante se pueden dividir en varios grupos. Entre ellos están::
- dibujos técnicos Wavetronix
- manuales de instrucciones SMARTSENSOR 105
- hojas de producto Wavetronix
- folletos informativos
- o etiquetas energéticas Wavetronix SMARTSENSOR 105
Todos son importantes, pero lo más importante desde el punto de vista del usuario de un dispositivo lo encontraremos en el manual de instrucciones Wavetronix SMARTSENSOR 105.

Un conjunto de documentos determinado como manual de instrucciones se divide también en tipos más detallados, tales como: instrucciones de montaje Wavetronix SMARTSENSOR 105, instrucciones de servicio, instrucciones cortas o instrucciones de usuario Wavetronix SMARTSENSOR 105. Dependiendo de la situación debes buscar el documento que necesitas. En nuestra página puedes consultar el manual de instrucciones más popular del producto Wavetronix SMARTSENSOR 105.

Manuales de instrucciones parecidos

El manual de instrucciones del dispositivo Wavetronix SMARTSENSOR 105, ¿cómo debería ser?
El manual de instrucciones, también determinado como el manual de usuario o simplemente instrucciones, es un documento técnico que tiene como objetivo ayudar a los usuarios a utilizar Wavetronix SMARTSENSOR 105. Las instrucciones normalmente las realiza un escritor técnico pero en un lenguaje comprensible para todos los usuarios de Wavetronix SMARTSENSOR 105.

El manual de instrucciones completo de Wavetronix debe contener unos elementos básicos. Una parte de ellos es menos importante, como por ejemplo: la portada / la página principal o las páginas de autor. Sin embargo, lo demás debe facilitarnos la información más importante desde el punto de vista del usuario.

1. Introducción y pistas sobre cómo orientarse con el manual Wavetronix SMARTSENSOR 105 - Al principio de cada manual se deben encontrar las indicaciones acerca de la manera de usar un manual de instrucciones. Debe contener información sobre dónde encontrar el índice Wavetronix SMARTSENSOR 105, preguntas frecuentes o problemas más comunes – son los apartados más buscados por los usuarios de cada manual de instrucciones.
2. Índice - listados de todos los consejos acerca de Wavetronix SMARTSENSOR 105 que encontraremos en el documento
3. Consejos de uso de las funciones básicas del dispositivo Wavetronix SMARTSENSOR 105 - que deben facilitarnos los primeros pasos durante el uso de Wavetronix SMARTSENSOR 105
4. Troubleshooting - una secuencia sistematizada de acciones que nos ayudará a diagnosticar los problemas más importantes con Wavetronix SMARTSENSOR 105
5. FAQ - las preguntas frecuentes
6. Datos de contacto Información acerca de cómo encontrar los datos de contacto del fabricante / servicio de Wavetronix SMARTSENSOR 105 en cada país si no somos capaces de solucionar el problema por nuestra cuenta.

¿Tienes una pregunta acerca de Wavetronix SMARTSENSOR 105?

Utiliza el formulario que se encuentra abajo

Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Wavetronix SMARTSENSOR 105, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Wavetronix SMARTSENSOR 105 probablemente compartirá una forma de solucionarlo.

Copia el texto de la imagen

Captcha
Nueva imagen

Comentarios (0)