-
Harbor Freight Tools 90860 - page 1
SOLAR P ANEL / MONO-CR YST AL Model 04815 / 12 W atts Model 91013 / 24 W atts Model 90860 / 50 W atts Model 90717 / 100 W atts INST ALLA TION AND OPERA TING INFORMA TION 3491 Mission Oaks Blvd., Camarillo , CA 93011 Visit our W eb site at http://www .harborfreight.com Cop yr ight © 2004 by Harbor F reight T ools ® . All rights reser ved. No por t ...
-
Harbor Freight Tools 90860 - page 2
SKUs 04815, 91013, 90860, & 90717 Page 2 GENERAL SAFETY W ARNINGS AND PRECA UTIONS 1. KEEP W ORK AREA CLEAN AND DR Y . Cluttered, damp or wet work areas invite injuries. 2. KEEP CHILDREN A W A Y FR OM WORK AREA. Do not allow children to handle this product. 3. ST ORE IDLE EQUIPMENT . When not in use, tools and equipment should be stored in a dr ...
-
Harbor Freight Tools 90860 - page 3
SKUs 04815, 91013, 90860, & 90717 Page 3 6. Always wear ANSI approved splash-resistant safety goggles when working with tools and equipment. If working around batteries also wear acid resistant work glov es. Any spilled acid must be w ashed off immediately . 7. INDUSTRIAL APPLICA TIONS MUST FOLLO W OSHA REQUIREMENTS. 8. DO NO T O VERREA CH. K e ...
-
Harbor Freight Tools 90860 - page 4
SKUs 04815, 91013, 90860, & 90717 Page 4 UNP A CKING When unpacking, chec k to make sure all par ts shown on the P ar ts List (page 9) are included. If any par ts are missing or brok en, please call Harbor F reight T ools at the number shown on the cover of this manual as soon as possible. SPECIFIC PRODUCT W ARNINGS AND PRECA UTIONS 1. THIS PRO ...
-
Harbor Freight Tools 90860 - page 5
SKUs 04815, 91013, 90860, & 90717 Page 5 T o Mount The Solar P anel At An Angle: 1. NO TE: F or increased pic kup of solar energy , and to minimiz e the collection of debris on the Solar P anel, it is recommended that the Solar P anel be installed on the mount- ing surface at an angle. (See Figure C, next page.) 2 . In order to mount the Solar ...
-
Harbor Freight Tools 90860 - page 6
SKUs 04815, 91013, 90860, & 90717 Page 6 3. T o secure the tw o angle brac kets to the mounting surf ace, drill two 1/4” holes though the base of each angle brac ket. Then, dr ill f our 1/4” holes, appropriately spaced, through the mounting surface. Use four screws, lock-washers, and nuts (not provided). (See Figure C.) T o Connect The Sola ...
-
Harbor Freight Tools 90860 - page 7
SKUs 04815, 91013, 90860, & 90717 Page 7 TYPICAL SINGLE SOLAR P ANEL CONNECTION (12 VOL T): FIGURE D Some parts shown are not included-see Parts List, page 9. ...
-
Harbor Freight Tools 90860 - page 8
SKUs 04815, 91013, 90860, & 90717 Page 8 TYPICAL MUL TIPLE SOLAR P ANEL CONNECTION (12 VOL T): FIGURE E Some parts shown are not included- see Parts List, page 9. TYPICAL DU AL SOLAR P ANEL CONNECTION (24 VOL T): FIGURE F Some parts shown are not included- see Parts List, page 9. ...
-
Harbor Freight Tools 90860 - page 9
SKUs 04815, 91013, 90860, & 90717 Page 9 CLEANING AND MAINTENANCE 1. NO TE: Alwa ys disconnect the Solar P anel(s) from the electrical charge controller before performing any cleaning, inspection, or maintenance upon the unit(s). 2. With the Solar P anel(s) disconnected from the charge controller , per iodically clean the Solar P anel(s) with m ...
-
Harbor Freight Tools 90860 - page 10
SKUs 04815, 91013, 90860, & 90717 Page 10 ASSEMBL Y DIA GRAM NO TE: Some par ts are listed and shown f or illustr ation purposes only , and are not a vailab le individually as replacement par ts. 1 2 3 5 6 NO TE: P ar t 4 -Alligator Clips- are only included with SKU 04815 and are not shown. ...
¿Tienes una pregunta acerca de Harbor Freight Tools 90860?
Utiliza el formulario que se encuentra abajo
Si con la ayuda del manual de instrucciones encontrado no has podido solucionar tu problema con Harbor Freight Tools 90860, haz una pregunta utilizando el formulario que se encuentra abajo. Si alguno de los usuarios ha tenido un problema parecido con Harbor Freight Tools 90860 probablemente compartirá una forma de solucionarlo.