Français dropdown-ico

Manuel d’utilisation Hitachi C10FL

32 pages 4.34 mb
Télécharger

Aller à la page of 32

Summary
  • Hitachi C10FL - page 1

    WARNING Improper and unsafe use of this power tool can result in death or serious bodily injury! This manual contains important information about product safety. Please read and understand this manual before operating the power tool. Please keep this manual available for others before they use the power tool. INSTRUCTION MANUAL AND SAFETY INSTRUCTI ...

  • Hitachi C10FL - page 2

    2 SECTION PAGE Know Your Stationary Table Saw ........................................ 10 Glossary of Terme ................................................................. 11 Assembly and Adjustments ................................................. 12 Operation ............................................................................... 19 Ma ...

  • Hitachi C10FL - page 3

    — 3 — WARNING Some dust created by power sanding, sawing, grinding, drilling and other construction activities contains chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints • Crystalline silica from bricks, cement and other m ...

  • Hitachi C10FL - page 4

    — 4 — POWER TOOL SAFETY WARNING Before using your table saw, it is critical that you read and understand these safety rules. Failure to follow these rules could result in serious injury or damage to the table saw. Good safety practices are a combination of common sense, staying alert and understanding how to use your power tool. To avoid mistak ...

  • Hitachi C10FL - page 5

    — 5 — TABLE SAW SAFETY 1. ALWAYS USE SAW BLADE GUARD, splitter and anti- kickback pawls for every operation for which they can be used, including through sawing. Through sawing operations are those in which the blade cuts completely through the workpiece when ripping or crosscutting. 2. ALWAYS HOLD WORK FIRMLY against the miter gauge or rip fen ...

  • Hitachi C10FL - page 6

    — 6 — ELECTRICAL REQUIREMENTS AND SAFETY POWER SUPPLY REQUIREMENTS WARNING To avoid electrical hazards, fire hazards or damage to the table saw, use proper circuit protection. Always use a separate electrical circuit for your tools. This power tool is wired at the factory for 120V operation. Connect it to a 120V, 15 Amp circuit and use a 15 Amp ...

  • Hitachi C10FL - page 7

    — — 7 ACCESSORIES AND ATTACHMENTS RECOMMENDED ACCESSORIES WARNING Visit your Hardware Department or see the Power and Hand Tools Catalog to purchase recommended accessories for this power tool. TOOLS NEEDED FOR ASSEMBLY TOOLS NEEDED Medium screwdriver #2 Philips screwdriver Straight edge Adjustable wrench Combination square 4mm Hex wrench 17mm ...

  • Hitachi C10FL - page 8

    — 8 — TABLE OF LOOSE PARTS ITEM DESCRIPTION QUANTITY A. Table saw assembly 1 B. Table extension wing 2 C. Rear table extension rail 2 D. Front table extension rail 2 E. Rail cover 6 F. Blade guard and splitter 1 each G. Adhesive washer 5 H. Rip fence 1 I. Miter gauge 1 J. Dust chute 1 K. Blade wrench 1 L. Push stick 1 M. Dodo table insert 1 N. ...

  • Hitachi C10FL - page 9

    — — 9 UNPACKING YOUR STATIONARY TABLE SAW A B C D E F G H I J K L M N O P Q VW X Y Z AA BB CC DD EE ...

  • Hitachi C10FL - page 10

    — 10 — KNOW YOUR STATIONARY TABLE SAW Miter Gauge Blade Guard Rip Fence ON/OFF Switch with key Leg Stand T able Extension (Right) T able Extension (Left) Blade T ilt Scale Blade T ilting Handwheel Blade Elevation Handwheel Castar Miter Gauge Storage Rip Fence Storage Splitter T able Insert T able ...

  • Hitachi C10FL - page 11

    — — 1 1 GLOSSARY OF TERMS HITACHI PROFESSIONAL TABLE SAW TERMS MITER GAUGE - A guide used for crosscutting operations that slides in the tabletop channels located on either side of the blade. It helps make accurate straight or angle cuts. RIP FENCE - A guide used for rip cutting that clamps to the tabletop. It allows the workpiece to be straigh ...

  • Hitachi C10FL - page 12

    — — 12 ASSEMBLY AND ADJUSTMENTS ASSEMBLE TABLE SAW TO STAND (Fig. A, B) 1 . Place protective corrugated cardboard or old blanket on floor to protect the saw table surface. 2 . Place the saw up-side down on the protective material (Fig. B). 3 . Position the recessed-side dust chute and the stand up-side down on the saw base. NOTE: Make sure fron ...

  • Hitachi C10FL - page 13

    — — 13 ASSEMBLY THE TABLE EXTENSION (Fig. C) 1 . Place the left table extension next to the saw table, aligning the mounting holes (1). 2 . Place bolts (2) and thread in mounting holes. 3 . Place a straight edge or combination square on the saw table, across the table extension. 4 . Adjust the mounting bolts (2) until the extension is flush wit ...

  • Hitachi C10FL - page 14

    — — 14 Installing the blade guard assembly (Fig. G) 1. Remove the table insert. 2. Unlock the blade bevel lock knob (1). 3 With the blade evevation handwheel (2), raise the blade to the maximum height. 4. Using the blade tilting handwheel, tilt the blade to 45 on the bevel scale. 5. Lock the blade tilt locking knob. 6. Locate the splitter assem ...

  • Hitachi C10FL - page 15

    — — 1 5 REMOVING THE BLADE (Fig. I) WARNING To avoid injury from an accidental start, make sure the switch is in the OFF position and the plug is disconnected from the power source outlet. 1. Remove the table insert and raise the blade to the maximum height by turning the blade elevation handwheel clockwise. 2. Lift the blade guard and position ...

  • Hitachi C10FL - page 16

    — 16 — 6. The, re-loosen the bevel lock handle and reset the blade at the maximum bevel position (45 ° ), then tighten the bevel lock handle. 7. Check again to see if the blade is 45 ° to the table. If not, repeat step 5. Fig. K 3 4 BLADE TILTING INDICATOR (Fig. L) 1. When the blade is positioned at 90 ° , adjust the blade tilt pointer to re ...

  • Hitachi C10FL - page 17

    — — 1 7 INSTALLING THE TABLE INSERT (Fig. N) The table insert has been previously installed on your unit. However, you must verify that the table insert is flush with the table top surface on all four corners of the insert. If the table insert is not flush with the table, adjust the four bolts (1) with a 4mm hex. wrench until it is parallel wit ...

  • Hitachi C10FL - page 18

    — — 18 RIP FENCE ADJUSTMENT (Fig. R) 1 . For adjustments, position the fence to the right of the blade, parallel with the miter gauge groove. 2 . Place the rear clamp (1) of the fence on the back rail of the table, and lower the front end over the front rail (2). Push the handle (3) down to lock. 3 . To change the position of the fence, lift up ...

  • Hitachi C10FL - page 19

    — — 1 9 OPERATION Fig. V 1 2 3 OVERLOAD PROTECTION This saw has an overload relay button that resets the motor after it shuts off due to overloading or low voltage. If the motor stops during operation, turn the ON / OFF switch to the OFF position. Wait about five minutes for the motor to cool, push in on the reset button and turn the switch to ...

  • Hitachi C10FL - page 20

    — — 2 0 RIPPING (Fig. W, X) WARNING To prevent serious injury:  Never use a miter gauge when ripping.  Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury.  Keep both hands away from the blade and clear from the path ...

  • Hitachi C10FL - page 21

    — — 2 1 CROSSCUTTING (Fig. Y) To prevent serious injury: Do not allow familiarity or frequent use of your table saw to cause careless mistakes. Remember that even a careless fraction of a second is enough to cause a severe injury. Keep both hands away from the blade and the path of the blade. 1. Remove the rip fence and place it in the "st ...

  • Hitachi C10FL - page 22

    — — 2 2 USING WOOD FACING ON THE RIP FENCE (Fig. DD) When performing some special cutting operations, add a wood facing (1) to the side of the rip fence between the fence and the blade where you will be cutting (2). 1 . Use a smooth & straight 3/4" thick wood board (1) measure as long as the rip fence is. 2. Attach the wood facing to t ...

  • Hitachi C10FL - page 23

    — — 2 3 MAINTENANCE MAINTAINING YOUR TABLE SAW GENERAL MAINTENANCE For your own safety, turn the switch OFF and remove the switch key. Remove the plug from the power source outlet before maintaining or lubricating your saw. 1. Clean out all sawdust that has accumulated inside the saw cabinet and the motor. 2. Polish the saw table with an automo ...

  • Hitachi C10FL - page 24

    — 24 — (Rocker Switch) (Power Cord) (GROUND) (Green) (CIRCUIT BREAKER SWITCH) Black Blue (GROUND) Brown (BLACK) Black (Black) (Black) (WHITE) Green (BLACK) (WHITE) (Motor) Blue (WHITE) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (BLACK) (Motor) (BLACK) (WHITE) (GROUND) Green (Power Cord) (Rock ...

  • Hitachi C10FL - page 25

    — 25 — SYMPTOM Saw will not start Does not make accurate 45 ° and 90 ° rip cuts Material pinched blade when ripping Material binds on splitter Saw makes unsatisfactory cuts Material kicked back from blade Blade does not raise or tilt freely Blade does not come up to speed Machine vibrates excessively Does not make accurate 45 ° and 90 ° cro ...

  • Hitachi C10FL - page 26

    — 26 — PUSH STICK Make from 1/2 ” or 3/4 ” wood or thickness less than width of material to be cut. CAUTION! Use only good strong wood or plywood. Use a jigsaw or bandsaw to cut out. Cut off here to push 1/4 ” wood. Cut off here to push 1/2 ” wood. 1/2 ” Squares. Optional hanging hole. Notch to help prevent hand from slipping. ...

  • Hitachi C10FL - page 27

    — 27 — ...

  • Hitachi C10FL - page 28

    — 28 — PARTS LIST 10" STATIONARY TABLE SAW MODEL NO. C10FL Always order by I.D. Number PARTS LIST FOR SCHEMATIC A I.D. Description Size Qty 1550 CR. RE.COUNT HD. TAPPING SCREW M4*16-16 2 2372 TABLE 1 2374 BODY 1 2376 HEIGHT LEVER SEAT 1 2378 CUTTER SHAFT 1 2379 INSERT 1 2389 WHEEL 1 2390 COMPRESSION SPRING 1 2552 HANDLE 1 09HZ SPINDLE PULL ...

  • Hitachi C10FL - page 29

    — 29 — 10" STATONARY TABLE SAW MODEL NO. C10FL SCHEMATIC A 29E2 ...

  • Hitachi C10FL - page 30

    — — 3 0 I.D. Description Size Qty 2 4 9 4 C A U T I O N L A B E L 4 0 C S E P O W E R C O R D C L A M P 2 0 J 9C S P R I N G W A S H E R 4 0 J B Y P A R A L L E L P IN 4 0 K 0 T H E X . H D . S C R E W A N D W A S H E R M 8 * 1. 25 - 2 0 4 0 K 7 F C R . R E . R O U N D W A S H E R H D . S C R E W M 5 * 0. 8- 8 2 0 K 7 L C R . R E . R O U N D W ...

  • Hitachi C10FL - page 31

    3 1 10" STATONARY TABLE SAW MODEL NO. C10FL SCHEMATIC B — — ...

  • Hitachi C10FL - page 32

    407 Code No. C99135161 Printed in Taiwan Issued by Shinagawa Intercity T ower A, 15-1, Konan 2-chome, Minato-ku, T okyo 108-6020, Japan Distributed by 3950 Steve Reynolds Blvd. Norcross, GA 30093 6395 Kestrel Road Mississauga ON L5T 1Z5 Hitachi Koki Co., Ltd. Hitachi Koki U.S.A., Ltd. Hitachi Koki Canada Co. ...

Fabricant Hitachi Catégorie Saw

Les documents que nous recevons du fabricant de l'appareilHitachi C10FL peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hitachi
- manuels d’utilisations C10FL
- fiches produit Hitachi
- dépliants
- ou étiquettes-énergie Hitachi C10FL
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hitachi C10FL.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hitachi C10FL, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hitachi C10FL. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hitachi C10FL.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hitachi C10FL, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hitachi C10FL par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hitachi C10FL.

Le manuel d’utilisation complet Hitachi, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hitachi C10FL - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hitachi C10FL, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHitachi C10FL qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hitachi C10FL - qui devraient nous aider dans les premières étapes lors de l'utilisation Hitachi C10FL
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hitachi C10FL
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hitachi C10FL dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hitachi C10FL?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hitachi C10FL, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hitachi C10FL il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)