-
Eaton 9130 - page 1
ENGLISH EATON 9130 UPS 5000 - 6000 VA User's guide Copyright © 2010 EATON All rights reserved. Se rv ic e a nd su pp or t: Ca ll yo ur lo ca l s er vi ce re pr es en ta ti ve 9130 UPS-EN ...
-
Eaton 9130 - page 2
Page 2 9130 UPS-EN Class A EMC Statements Requesting a Declaration of Conformity Units that are labeled with a CE mark comply with the following harmonized standards and EU directives: Harmonized Standards: IEC 61000-3-12 l EU Directives: 2006/95/EC, Council Directive on equipment designed for use within certain l voltage limits 2004/108/EC, Counci ...
-
Eaton 9130 - page 3
Page 3 9130 UPS-EN ENGLISH 1. Introduction 2. Installation 2.1 Inspecting the Equipment .............................................................................................. 5 2.2 Unpacking the Cabinet .................................................................................................... 5 2.3 Checking the Accessory Kit ..... ...
-
Eaton 9130 - page 4
Page 4 9130 UPS-EN 1. Introduction The Eaton® 9130 uninterruptible power system (UPS) protects your sensitive electronic equipment from the most common power problems, including power failures, power sags, power surges, brownouts, line noise, high voltage spikes, frequency variations, switching transients, and harmonic distortion. Power outages ca ...
-
Eaton 9130 - page 5
Page 5 9130 UPS-EN ENGLISH 2. Installation This section explains: Equipment inspection l Unpacking the cabinet l Checking the Accessory Kit l Product installation l Connecting the internal battery l Connecting the EBM(s) l Installation requirements l 2.1 Inspecting the Equipment If any equipment has been damaged during shipment, keep the shipping c ...
-
Eaton 9130 - page 6
Page 6 9130 UPS-EN 2. Installation 2.3 Checking the Accessory Kit Verify that the following additional items are included with the UPS: UPS user’s guide l Software Suite CD l USB cable l RS232 cable l ENGLISH EATON 9130 UPS 5000 - 6000 VA User's guide Copyright © 2009 EATON All rights reserved. EATON 8609 6 Forks Road Raleigh, NC 27615 U.S. ...
-
Eaton 9130 - page 7
Page 7 9130 UPS-EN ENGLISH 2. Installation 2.5 Connecting the internal battery Do not make unauthorized changes to the UPS; otherwise, damage may occur to your equipment and void your warranty. Do not connect the UPS to utility until installation is completed. To install the UPS: 1. Remove the UPS front cover ( see figure 5 ). To remove the cover: ...
-
Eaton 9130 - page 8
Page 8 9130 UPS-EN 2. Installation 2.6 Connecting the EBM(s) To install the optional EBM(s) for a UPS: A small amount of arcing may occur when connecting an EBM to the UPS. This is normal and will not harm personnel. Insert the EBM cable into the UPS battery connector quickly and firmly. 1. Plug the EBM cable(s) into the battery connector(s) as sho ...
-
Eaton 9130 - page 9
Page 9 9130 UPS-EN ENGLISH 2. Installation 2. Required cable cross-sections Table 2. Cable cross sections UPS power rating 5000 VA / 6000 VA Minimum of section required Terminal-block capacity Phase and neutral solid or stranded wire 6 mm² AWG 10 10 mm² AWG 8 Earthing solid or stranded wire 6 mm² AWG 10 10 mm² AWG 8 2.8 Installation depending o ...
-
Eaton 9130 - page 10
Page 10 9130 UPS-EN 2. Installation UPS with separate Input and Bypass inputs, supplied by separate sources (Figure 13) Change in SEA between upstream and downstream or galvanic isolation required (Figure 14) 8 10 11 Frequency converter (without Bypass input) (Figure 15) Configuration used when the frequency of the application differs from the Main ...
-
Eaton 9130 - page 11
Page 11 9130 UPS-EN ENGLISH 3. Power cables connection & Startup This section explains: Access to terminal block l Common input sources connection l Separate input sources connection l Frequency converter connection l UPS Initial startup l 3.1 Access to terminal block 1. Access to terminal block: remove the 4 screws of the terminal block cover ...
-
Eaton 9130 - page 12
Page 12 9130 UPS-EN 3. Power cables connection & Startup 3.3 Separate input sources connection This type of connection must be carried out by qualified electrical personnel. Before carrying out any connection, check that the upstream protection device Input source is open ("O") (OFF). Always connect the earthing wire first. JP L N L N ...
-
Eaton 9130 - page 13
Page 13 9130 UPS-EN ENGLISH 3. Power cables connection & Startup 3.5 UPS Initial Startup To start up the UPS: Verify that the total equipment ratings do not exceed the UPS capacity to prevent an overload alarm. 1. Verify that the internal batteries are connected. See "Connecting the internal battery" on page 7. 2. If optional EBMs are ...
-
Eaton 9130 - page 14
Page 14 9130 UPS-EN 4. Operation This chapter contains information on how to use the Eaton 9130, including front panel operation, operating modes, UPS startup and shutdown, transferring the UPS between modes, retrieving the Event Log, setting the power strategy, and configuring bypass settings, load segments, and battery settings. 4.1 Control Panel ...
-
Eaton 9130 - page 15
Page 15 9130 UPS-EN ENGLISH 4. Operation The table 4 shows the basic menu structure. Table 4. Menu Map for Display Functions Main Menu Submenu Display Information or Menu Function UPS Status Main status (mode and load) / Notice or Alarm status (if any) / Battery status (state and charge level) Event Log Displays up to 127 events and alarms. The Eve ...
-
Eaton 9130 - page 16
Page 16 9130 UPS-EN 4. Operation Power Strategy [Normal] [High Efficiency] See "Setting Power Strategy" on page 19. Normal Automatic start delay [No Delay] [Disabled] [1,2,...,32767 s] To define if the load turns automatically on, with the delay set after the utility return, if it has been shutdown by: - signal input with auto-restart opt ...
-
Eaton 9130 - page 17
Page 17 9130 UPS-EN ENGLISH 4. Operation 4.2 Operating Modes The Eaton 9130 front panel indicates the UPS status through the UPS indicators (see figure 20 on page 14). Normal Mode During Normal mode, the indicator illuminates solid and the UPS is powered from the utility. The UPS monitors and charges the batteries as needed and provides filtered po ...
-
Eaton 9130 - page 18
Page 18 9130 UPS-EN 4. Operation 4.3 UPS Startup and Shutdown To start up or shut down the UPS, see: "Starting the UPS" on page 18 l "Starting the UPS on Battery" on page 18 l "UPS Shutdown" on page 18 l Starting the UPS "Start on Bypass" settings can be used to power on capacitive loads. To start the UPS: 1. ...
-
Eaton 9130 - page 19
Page 19 9130 UPS-EN ENGLISH 4. Operation 4.5 Retrieving the Event Log To retrieve the Event Log through the display: 1. Press any button to activate the menu options, then select EVENT LOG. 2. Scroll through the listed events. To retrieve the Event Log through the serial port: 1. From the communication device connected to the serial port, send one ...
-
Eaton 9130 - page 20
Page 20 9130 UPS-EN 4. Operation 4.8 Configuring Battery Settings Set the UPS for the number of EBMs installed whether to run automatic battery tests, and automatic restart configuration. Configuring the UPS for EBMs To ensure maximum battery runtime, configure the UPS for the correct number of EBMs: 1. Press any button on the front panel display t ...
-
Eaton 9130 - page 21
Page 21 9130 UPS-EN ENGLISH 5. Communication This section describes the: Communication ports (RS-232 and USB) l Connectivity cards l Remote Power-off (RPO) l Relay output contacts l Programmable signal inputs l Modem operation l EATON® Power Management Software l Figure 21. Communication Options and Control Terminals. 5.1 Installing Communication ...
-
Eaton 9130 - page 22
Page 22 9130 UPS-EN 5. Communication RS 232 and USB Communication Ports To establish communication between the UPS and a computer, connect your computer to one of the UPS communication ports using an appropriate communication cable. See Figure 21 for the communication port locations. When the communication cable is installed, power management softw ...
-
Eaton 9130 - page 23
Page 23 9130 UPS-EN ENGLISH 5. Communication The RPO circuit is an IEC 60950 safety extra low voltage (SELV) circuit. This circuit must be separated from any hazardous voltage circuits by reinforced insulation. The RPO must not be connected to any utility connected circuits. Reinforced insulation to the l utility is required. The RPO switch must ha ...
-
Eaton 9130 - page 24
Page 24 9130 UPS-EN 5. Communication The table 10 shows the options for the relay output contacts. Table 10. Relay Output Configuration Options Relay Signal Description UPS ok Activated when the UPS is feeding the load on inverter or on bypass and no alarms are active On Bypass Activated when the UPS is NOT on bypass operation On Battery Activated ...
-
Eaton 9130 - page 25
Page 25 9130 UPS-EN ENGLISH 5. Communication Table 12. Polarity Options Input Description High Active state on high voltage (+Udc) level Low Active state on low voltage (GND or -Udc) level 5.3 Eaton Power Management Software Suite Each Eaton 9130 UPS ships with Eaton Power Management Software Suite. To begin installing, see the instructions accompa ...
-
Eaton 9130 - page 26
Page 26 9130 UPS-EN 6. UPS Maintenance This section explains how to: Care for the UPS and batteries l Replace the UPS internal batteries and Extended Battery Modules (EBMs) l Test new batteries l Recycle used batteries or UPS l 6.1 UPS and Battery Care For the best preventive maintenance, keep the area around the UPS clean and dust free. If the atm ...
-
Eaton 9130 - page 27
Page 27 9130 UPS-EN ENGLISH 6. UPS Maintenance Servicing should be performed by qualified service personnel knowledgeable of batteries and l required precautions. Keep unauthorized personnel away from batteries. Batteries can present a risk of electrical shock or burn from high short circuit current. Observe l the following precautions: 1) Remove w ...
-
Eaton 9130 - page 28
Page 28 9130 UPS-EN 6. UPS Maintenance Figure 28. Disconnecting the UPS internal batteries. 3. Disconnect one of the 4 battery trays. Remove the plastic protection above the connector and disconnect the battery tray ( see figure 29 ). Figure 29. Disconnecting the internal battery tray. 4. Remove the metal fixing part to free the battery tray ( see ...
-
Eaton 9130 - page 29
Page 29 9130 UPS-EN ENGLISH 6. UPS Maintenance 6. Slide the new battery package into the cabinet. Push the battery package in firmly. 7. Screw the metal part to fix the battery tray. Make sure main internal battery connector is disconnected. 8. Connect the battery tray and put back the plastic protection above the connector. A small amount of arcin ...
-
Eaton 9130 - page 30
Page 30 9130 UPS-EN 6. UPS Maintenance 6.6 Recycling the Used Battery or UPS Contact your local recycling or hazardous waste center for information on proper disposal of the used battery or UPS. Do not dispose of the battery or batteries in a fire. Batteries may explode. Proper disposal of l batteries is required. Refer to your local codes for disp ...
-
Eaton 9130 - page 31
Page 31 9130 UPS-EN ENGLISH 7. Specifications 7.1 Model Specifications This section provides the following specifications: Communication options l Model lists l Weights and dimensions l Electrical input and output l Environmental and safety l Battery l Table 13. Communication Options Communication Bay (1) available independent communication bay for ...
-
Eaton 9130 - page 32
Page 32 9130 UPS-EN 7. Specifications Table 18. Electrical Input Model Default Input (Voltage/Current) Selectable Input Voltage Range Voltages at 100 % Load PW9130i5000T-XL 230 V / 21.7 A 200*, 208*, 220, 230, 240 180–276 Vac PW9130i6000T-XL 230 V / 26.1 A 200*, 208*, 220, 230, 240 180–276 Vac 208 V are derated by 10 %. Table 19. Electrical Inp ...
-
Eaton 9130 - page 33
Page 33 9130 UPS-EN ENGLISH 7. Specifications Table 22. Environmental and Safety Surge Suppression EN 61000-2-2 EN 61000-4-2, Level 3 EN 61000-4-3, Level 3 EN 61000-4-4, Level 3 (also on signal ports) EN 6100-4-5, Level 3 Criteria A (IEEE C62.41 6 KV) EN 61000-4-6, Level 3 EN 61000-4-8, Level 4 EN 6100-4-11 EMC Certifications CE per IEC/EN 62040-2, ...
-
Eaton 9130 - page 34
Page 34 9130 UPS-EN 8. Troubleshooting The Eaton 9130 is designed for durable, automatic operation and also alerts you whenever potential operating problems may occur. Usually the alarms shown by the control panel do not mean that the output power is affected. Instead, they are preventive alarms intended to alert the user. In general: Events are si ...
-
Eaton 9130 - page 35
Page 35 9130 UPS-EN ENGLISH 8. Troubleshooting Overload Power requirements exceed the UPS capacity (greater than 100 % of nominal; see page 31 for specific output overload ranges). Remove some of the equipment from the UPS. The UPS continues to operate, but may switch to Bypass mode or shut down if the load increases. The alarm resets when the cond ...
-
Eaton 9130 - page 36
Page 36 9130 UPS-EN 8.2 Silencing the Alarm Press any button on the front panel display to silence the alarm. Check the alarm condition and perform the applicable action to resolve the condition. If the alarm status changes, the alarm beeps again, overriding the previous alarm silencing. 8.3 Service and Support If you have any questions or problems ...
Avez-vous une question à propos de Eaton 9130?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Eaton 9130, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Eaton 9130 il est probable qu’il a envie de partager la façon de le résoudre.