Français dropdown-ico

Manuel d’utilisation Pfaff hobbylock 788

52 pages Non applicable
Télécharger

Aller à la page of 52

Summary
  • Pfaff hobbylock 788 - page 1

    p fr: hobbylock 787 • 788 Instruction manual ...

  • Pfaff hobbylock 788 - page 2

    IMPORTANT SAFETY INSTRUCTIONS -This sewing rrachine is designed and manufactured for HOUSEHOLD use only. When using an electric appliance, basic safety precautions should always be followed, including the following: Read all instructions before using this sewing machine. D AIIG ER To reduce the risk of electric schock: 1. The sewing machine should ...

  • Pfaff hobbylock 788 - page 3

    • 2.3 .6 .8 • . 10 • . . 11 • 11 • . . 12 • . 12 • • 13 • . 14 • . . 14 • . - 14 • . . 15 • . . 16 • . 17 • . . 18 19 20 20 21,22 23 23 24 24 25 26,27 28 29 29 30 31 32 32 33 34—39 40—41 42 43 46 43—50 51 Contents Controls of the sewing machine Accessory box Electrical connection Master switch and sewing light Fo ...

  • Pfaff hobbylock 788 - page 4

    (0 ...

  • Pfaff hobbylock 788 - page 5

    Controls of the sewing machine 1 Thread spool stand 2 Carrying handle 3 Left needle thread tension dial 4 Right needle thread tension dial 5 Right looper thread tension dial 6 Left looper thread tension dial 7 Thread tension cover 8 Lint box 9 Handwheel 1 0 Looper cover with recess 11 Upper knife 1 2 Swivel-type work support 1 3 Needle plate 14 Sew ...

  • Pfaff hobbylock 788 - page 6

    Accessory box Swing open work support 1 2 and pull out accessory box 24. The accessory box can only be inserted in its compartment when held as shown in the illustration at left. The guide groove is up and the projection of the box faces the machine. Electrical connection Use this machine only on a flat surface or on a special machine table. Connec ...

  • Pfaff hobbylock 788 - page 7

    Switching the machine ON and OFF Power and sewing light together are switched on and off with master switch 21. Switching on: Press switch. Machine and sewing light are switched on. Switching off: Press switch again. Machine and sewing light are switched off. Foot contro’ The speed of the Hobbylock is regula ted as follows: The more you press the ...

  • Pfaff hobbylock 788 - page 8

    e3-O ———— I How to handle the thread spool stand Pull thread spool stand 1 as far as it will go in the direction indicated by the arrow. Fully extend telescopic thread guide bar 19. Slowly turn the two upper tele — scopic sections until you hear their detent balls snap in place. After use fold up telescopic thread guide bar 19. read spo ...

  • Pfaff hobbylock 788 - page 9

    1 Opening and closing looper cover and work support Push looper cover 10 fully to the right, hold it, and swing it down. To close the looper cover, push it up until it locks. To open work support 12. push it in the direction indicated by the arrow. To close the work support, push it lightly until it locks. Behind the looper cover converter 41 (Hobb ...

  • Pfaff hobbylock 788 - page 10

    CD D ao CD U) 7 - U) O(DCD D CD a U)3CD “U)CD •c CDm -, CD CD a DC a cT -CD CD CD D ci o D CD 1 T C U) 3CD 0 CD CD ciCD • CD<CD ••‘ • o CDOD C) CD CD- -1 -l 0 CDZT CD CO CD o ci —. .CflCD O •-“ — C) Z O CD __< lCD C — co 0 co 0 •0 CD U) (IC CT CD CD—. -. 3 CD U) ...

  • Pfaff hobbylock 788 - page 11

    Threadng the left looper Thread guide 9 is threaded by means of looper threader 40. 1 The mark on handwheel 9 must be aligned with the mark on the hou sing. 2. Tauten the thread a little. 3. Push the slide of the looper threader fully to the left, then pull lightly on the thread and allow the slide to return slowly. By this means the thread is plac ...

  • Pfaff hobbylock 788 - page 12

    Threading the right needle Threading of guide wires 18 and 22 is shown on page 7. In the left-hand illustration the threa ding path is shown from green tension 1 up to right needle eye 6. Thread the needle from the front. The use of needle threader 42 is desc ribed on the next page. Threading the left needle Threading of guide wires 18 and 22 is sh ...

  • Pfaff hobbylock 788 - page 13

    is Needle threader Lower the sewing foot by means of lif ting lever 16. Turn the hand wheel until right looper 31 is positioned right of the needle (see top of page 18). Place the thread in slot A of needle threader 42 and tauten it a little, holding the needle threader a little turned to the front. With the needle located between the two guide lug ...

  • Pfaff hobbylock 788 - page 14

    Inserting the lint box: Insert the two tabs of lint box 8 down wards in the recess of looper cover 10. Then push the bottom of the box against the machine. For removal of the lint box, use the revese order. Seam allowance If the cutting is guided along below mark N on looper cover 10, a seam allowance of 16 mm must be taken into consideration when ...

  • Pfaff hobbylock 788 - page 15

    Sewing test After threading, a sewing test should be made. Raise sewing foot lever 16, as shown in the illustration. Hold the thread ends with your left hand while turning the hand wheel with your right hand in the direction indica ted by the arrow on the wheel. Hold the threads taut and lay them back under sewing foot 14. Make sure the threads int ...

  • Pfaff hobbylock 788 - page 16

    Points to observe during sewing Thread cutter In order to be able to use thread cutter 39 it is necessary to sew beyond the end of the seam. Draw the resulting thread chain through the thread cutter from the rear (see illustration below left). Securing the seam: Knot the thread chain. For knit fabrics, a crochet needle can be used to pull the threa ...

  • Pfaff hobbylock 788 - page 17

    Face side Setting the standard thread tension N zijE. Li .:.• ;1 thread Left looper thread Right Left needle thread needle thread Reverse side Optimum seam appearance depends on the type of fabric used, on the thread size, and on the thread tension setting. Set the N on the thread tension dials opposite the round colored mark on thread tension ...

  • Pfaff hobbylock 788 - page 18

    1. The right looper thread C is too tight (red thread tension). 2. The left looper thread 0 is too loose (yellow thread tension(. 3. Both tensions must be corrected. 1. The left looper thread 0 is too tight (yellow thread tension). 2. The right looper thread C is too loose (red thread tension). 3. Both tensions must be corrected. Possibilities requ ...

  • Pfaff hobbylock 788 - page 19

    i 3-thread overedge seam Left needle Right needle UJL ih rn Standard seam width N Standard seam width N -- 57mm 3,5m Max. seam width 7.2 mm Max. seam width 5 mm 3-thread overedge seam: Threading of the right and left looper is described on pages 8 and 9. The slide of converter 41 must be set at its right position B (see p. 18). The 3-thread overedg ...

  • Pfaff hobbylock 788 - page 20

    Engaging the converter (HL 788) For the Hobbylock 787 the converter is available as a special accessory part (see p. 42 and 46). Turn the hand wheel until right looper 31 is positioned right of the needle. For sewing with converter 41 the right looper thread must be cut off and pul led out of the looper eye. All seams sewn with converter 41 are onl ...

  • Pfaff hobbylock 788 - page 21

    2-thread overeoge seam er n Adjustable range 5.2 to 7.2 mm Adjustable range 3 to 5 mm r is Left needle Standard seam width N Rght needle Standard seam width N B / / / /, /1 / ‘ The left-hand llustration shows the 2-thread oeredge seam with correctly set thread tensions. Possible correction requirements: 1. Looper read A is too loose (yellow threa ...

  • Pfaff hobbylock 788 - page 22

    Thread chart for 2-, 3-, 4-thread overedge seam Material Thread Stitch length Light materials: Organdy, light-knit Cotton No. 80- 100 2.0 to 4.0 mm fabric. Taffeta, silk, Silk No. 80- 100 lining materials Synthetic thread No. 70- 140 Medium-heavy materials: Cotton No. 60-100 2.0 to 4.0mm Cotton, tricot, Silk No. 50-100 linen, dress materials Synthe ...

  • Pfaff hobbylock 788 - page 23

    Adjusting the differential feed on the Hobbylock 788 The differential feed prevents inter-ply shift. It consists of two feed dogs, arranged one behind the other, which both pick up and move the workpiece at the same time. The feed amount of either feed dog can be set separately. It is possible to have the workpiece moved more by the front feed dog ...

  • Pfaff hobbylock 788 - page 24

    This table indicates possible settings of the differential feed of the Hobbylock 788. In order to make sure about the setting required for the fabric you wish to process, a sewing test has to be made. — The differential feed can also be set during sewing. Setting of dif- Correct ferential feed Illustration seam Fabric 0.5 to N 1 a Nylon, tricot, ...

  • Pfaff hobbylock 788 - page 25

    I Disengaging the upper knife Remove lint box 8. Open work support 1 2 and looper cover 1 0. If necessary, loosen upper knife arresting screw 37. Push rotary lever 27 of the axial upper knife guide fully to the right, hold it, and turn it forwards until the pin enga ges in the hole of the knife. Now the upper knife is disengaged. Adjusting the seam ...

  • Pfaff hobbylock 788 - page 26

    Changing the sewing foot Raise sewing foot lifting lever 1 6. Disengage the sewing foot by pressing lever F. Engaging the sewing foot: Place the sewing foot under the sewing foot holder so that when you lower the sewing foot lifting lever, crosspiece G of the foot engages in groove H of the sewing foot holder. Changing the light bulb: Pull out the ...

  • Pfaff hobbylock 788 - page 27

    Cleaning the thread tensions; — At the points indicated, press thread - tension cover 7 in the direction of the I arrows, thus loosening the cover, then - 1 remove it towards the front. / - Set the 4 thread tensions at — 5. Use the cleaning brush (accessories) to remove dust and lint from between the 1 ‘ tension discs of the 4 tensions. — J ...

  • Pfaff hobbylock 788 - page 28

    Fold-over 3-thread roiled hem sewn with polyester thread 120 -140. A rolled hem is used for light, delicate fabrics and is an attractive finish for open edges. Without any effort you can sew professional rolled hems on neck scarves, shawls and valances. This rolled hem is sewn with three threads (see page 27). Face side Reverse side MW ece side R ...

  • Pfaff hobbylock 788 - page 29

    Rolled hem with polyester thread Preparation of the sewing machine: Needle: remove left needle / insert right needle Sewing foot: engage rolled-hem foot ,,R” Seam width: from 3.0 to 4.0 mm (depending on material) Stitch length: from 1 .0 to 2.0 mm (short stitch length) Thread: polyester thread 120-140 for green, red and yellow thread tensions Thr ...

  • Pfaff hobbylock 788 - page 30

    Hobbylock 788 2-thread rolled hem sewn with converter 41 (for this purpose the slide must be in position Asee p. 181. Needle: insert right needle Sewing foot: rolled-hem sewing foot Seam width: N (3.5 mm> Stitch length: 1 .0 to 2.0 mm For the Hobbylock 787 the converter is available as special accessory part (see p. 42 and 46>. 2-thread rolle ...

  • Pfaff hobbylock 788 - page 31

    Changing the needles Pull out the mains plug. Lower the sewing foot. Turn the hand wheel in the direction of the arrow until the needle bar is at its highest position. Hold the needle with the tweezers, loo sen screw A or B with the small screw driver, and pull the needle downwards. out of the needle holder. Inserting the needle The needle has to b ...

  • Pfaff hobbylock 788 - page 32

    Changing the upper knife: Pull out the mains plugl Unscrew knife retaining screw 35 and remove upper knife 11. Disengage the upper knife, see page 23. Insert the new upper knife and tighten its retaining screw securely. Reset upper knife to its cutting position. Set upper knife with knife guide 27 up (cutting position>. Turn the handwheel until ...

  • Pfaff hobbylock 788 - page 33

    Changing the lower knife Pull out the mains plug! Disengage the upper knife (see p. 23). Remove retaining screw 34 of lower knife 33. Turn seam width adjustment knob 26 at position 3 (smallest seam width). Hold the new lower knife in such a way that the pin extends into the front hole of the lower knife. Then screw down retaining screw 34 together ...

  • Pfaff hobbylock 788 - page 34

    Upper knife arresting Sewing very thick fabrics and workpie ces with different ply thicknesses: On this machine, all kinds of fabric from extremely thin to extremely thick can be processed. When sewing extre mely thick fabrics or workpieces with different thicknesses, the screw of the upper knife must be tightened, as shown in the illustration. By ...

  • Pfaff hobbylock 788 - page 35

    Oiling the machine: Every time before you take the machine into operation, you should apply a little oil to the places indicated. The bus hings and other important moving parts are made of special material and need to be oiled only once or twice a month. One to two drops of PFAFF sewing machine oil are sufficient. 33 ...

  • Pfaff hobbylock 788 - page 36

    Stitch selection table The values set for thread tension, stitch length, needle size, and the differential feed setting (788) are only basic settings that have to be varied according to the application, i.e. to the type of fabric, the fabric thickness, and the thread used. The sewing foot must be selected according to the seam width (see ill, at ri ...

  • Pfaff hobbylock 788 - page 37

    oo 6uiws weq po WW ZL O 99 JO SLflP!M WS JO N ‘J 6U1MS ww 9 o 17 JO Sqp!M WS JOJ N OOJ 6U!M89 ww 9 O E O sqpiM WEeS JO EN 004 6U!MES ...

  • Pfaff hobbylock 788 - page 38

    Stitch type (see table Needle thread Looper thread Needle-System on p. 20) tension tension 15 1 H blue green red yellow A [ B 2-thread rolled hem narrow) light — 2 — 1 to N medium — 2 — 1 to N Size Folded 2-thread roiled hem light N — 1 to N Size medium N — 1 to N 75 F 11 3-thread overedge seam (narrow) light — 1 N N Size medium N N N ...

  • Pfaff hobbylock 788 - page 39

    c) ...

  • Pfaff hobbylock 788 - page 40

    Stitch type (se:tle Needle thread Looper thread Ntm on p 20) tension tension 15 x I H blue green red yellow A B Decoratme 3-thread sergng seam 3-thread tight — 2 + 2 ± 4 fiatioce Seam) Size medium — 2 — 2 + 4 90 14 heavy —2 -4-2 +4 Decoratme 3-thread sergrng seam wide tight — 5 + 1 + 3 3thread fiatiock seam) medium -5 +1 +3 90 heavy —5 ...

  • Pfaff hobbylock 788 - page 41

    zz zz 0 UZz ZZD Zzm czD aZzzi Ezzi 2 I I I tZZ HL_ iI I t3 CJzj Cj ij U_—LtJ Co /;::::::z 1 - — 7/’ C9 . z z z z Ui -->/ —‘ C,) 3 r CD z z z z z z z I- - CD c co . ,I — • • : cc, ...

  • Pfaff hobbylock 788 - page 42

    Sewing problems and solutions These machines have been developed for easy operation, and there are no difficult adjustments to be made. Sewing problems of the kind described below may occur due to minor adjustment. and operation errors. They can easily be corrected by following the instructions below. Problem Cause Solution Needle breakage Needle b ...

  • Pfaff hobbylock 788 - page 43

    Prob’em Cause So’ution Machine does not Power supply interrupted Close looper cover 10 or run although mas- looper cover 1 0 or work support 1 2 (see p. 7( ter switch is on work support 1 2 (see p. 7( Fabric not neatly Sewing lint between upper Clean knives (see p. 32) trimmed and lower knife Upper knife blunt Exchange upper knife (see p. 30) P ...

  • Pfaff hobbylock 788 - page 44

    Accessories 1 Screwdriver (big) 2 Screwdriver (small) 3 Lint brush 4 Tweezers 5 Upper knife 6 Thread unreeling disc 7 Needles 8 Sewing machine oii 9 Rolled hem sewing foot (R) 10 Sewing foot N2 11 Sewing foot N3 1 2 Thread spool net 13 Needle threader 2 Description of specia’ accessories on pp.43—50 Elastic tape sewing foot Part No. 29-924 993- ...

  • Pfaff hobbylock 788 - page 45

    Thread spool net Very useful for synthetic threads which tend to become loose, unravel and slip down (Fig. A>. Thread unreeling disc The thread unreeling disc shown as item 6 of the accessories is used for smaller thread spools. Remove thread spool centering piece 36 from the thread reel pin. Put the thread spool on the thread reel pin and place ...

  • Pfaff hobbylock 788 - page 46

    fabric N beads 1—1.5mm Fig. 1 Fig. 2 Bead sewing foot (Fig. 1) This special sewing foot is for sewing on beads, sequins, strass bands, lead- and ordi nary cords. These operations are carried out with one needle. 1. Set differential feed at N (Hobbylock 788) 2. Insert bead sewing foot 3. For small beads use the right needle For large beads use the ...

  • Pfaff hobbylock 788 - page 47

    E’astic tape sewing foot This special sewing foot is for sewing on an elastic tape; in the same opera tion the fabric is trimmed and serged, and also gathered by the contracting elastic tape. Preparing the machine set at N (Hobbylock 788) use 1 or 2 needles, depending on tape width insert elastic taping foot 4 to 4.5 approx. 4 Inserting the elast ...

  • Pfaff hobbylock 788 - page 48

    Taping foot 1 This special sewing foot is for sewing on tapes. On stretch materials (knitwear) the seams are prevented from stretching when a tape is sewn on. Preparing the machine Differential feed setting: Needles: set at N (Hobbylock 788) use 1 or 2 needles, deoending on tape wiath Stitch width: Stitch length: Thread tension: 3 to 5 mm (adjustab ...

  • Pfaff hobbylock 788 - page 49

    Cording foot This special sewing foot s used for sewing a cording tape between two fabric plies in one operation Preparing the machine set at N (Hobbylock 788) two needles or left one engage cording foot engaged 3 to 5 inserting the fabric plies 1. Raise the sewing foot 2. Set needle at its highest position 3. Place bottom ply, cording tape and top ...

  • Pfaff hobbylock 788 - page 50

    Shirring foot (Hobbylock 788) This special sewing foot is used for joi ning two pieces of fabric and shIrring the bottom ply in one operation. Preparing the machine set at N (Hobbylock 788) two or one engage shirring foot engaged ±3 to +5 Inserting the fabric plies 1. Raise the sewing foot. 2. Set needle at its highest position. 3. Place bottom fa ...

  • Pfaff hobbylock 788 - page 51

    Gimp thread sewing foot This special sewing foot is used for sewing in gimp threads (cords, synthe tic threads) up to a thickness of 1.0 mm. By this means a wavy, i.e. more firm hem finish is achieved (e.g. on wedding dresses, curtains, etc.). Preparing the machine set at N (Hobbylock 788) insert right needle (HL 787, 788) 3 to 4 mm 1.0 to 1.5 mm r ...

  • Pfaff hobbylock 788 - page 52

    A Specifications: Sewing foot Lubrication Sewing foot height . Needle system Needle size Number of threads 788/787 Dimensions Weight 788 / 787 . Contents of cardboard box • 1,300 stitches/mm. 3—7.2mm 1—4mm(HL788) 1 — 5 mm (HL 787) inged Manual 5mm 130/705 H or 1 5 x 1 H 75-9Oorll-14 2,3,4/3,4 315x280x330mm 8.5 kg/8.Okg 1 machine with motor ...

Fabricant Pfaff Catégorie Sewing Machine

Les documents que nous recevons du fabricant de l'appareilPfaff hobbylock 788 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Pfaff
- manuels d’utilisations hobbylock 788
- fiches produit Pfaff
- dépliants
- ou étiquettes-énergie Pfaff hobbylock 788
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Pfaff hobbylock 788.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Pfaff hobbylock 788, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Pfaff hobbylock 788. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Pfaff hobbylock 788.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Pfaff hobbylock 788, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Pfaff hobbylock 788 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Pfaff hobbylock 788.

Le manuel d’utilisation complet Pfaff, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Pfaff hobbylock 788 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Pfaff hobbylock 788, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPfaff hobbylock 788 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Pfaff hobbylock 788 - qui devraient nous aider dans les premières étapes lors de l'utilisation Pfaff hobbylock 788
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Pfaff hobbylock 788
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Pfaff hobbylock 788 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Pfaff hobbylock 788?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Pfaff hobbylock 788, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pfaff hobbylock 788 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)