Français dropdown-ico

Manuel d’utilisation Zenoah BT225

32 pages 1.05 mb
Télécharger

Aller à la page of 32

Summary
  • Zenoah BT225 - page 1

    OWNER / OPERA T OR MANUAL LINE TRIMMER BT01-00001 (501) The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. W ARNING Before using our products, please read this manual carefully to understand the proper use of your unit. W ARNING DRIVE UNIT 000001 and up ...

  • Zenoah BT225 - page 2

    SAFETY FIRST Instructions contained in warnings within this manual marked with a symbol concern critical points which must be taken into consideration to prevent possible serious bodily injury, and for this reason you are requested to read all such instructions carefully and follow them without fail. ■ WARNINGS IN THE MANUAL This mark indicates i ...

  • Zenoah BT225 - page 3

    2. Specifications ■ BT225 Overall size(LxWxH) ························································ 70.0(1780)x14.0(355)x9.5(241) in(mm) Dry weight w/o acc.··································································? ...

  • Zenoah BT225 - page 4

     4  (1) Read owner's manual before operating this machine. (2) Wear head, eye and ear protection. (3) Warning/Attention (4) Keep all children, bystanders and helpers 15 meters away from the brushcutter If warning label peel off or become soiled and impossible to read, you should contact the dealer from which you purchased the product to ...

  • Zenoah BT225 - page 5

    For safe operation and maintenance, symbols are carved in relief on the machine. According to these indications, please be careful not to make a mistake. (a) The port to refuel the "MIX GASOLINE" Position: FUEL TANK CAP (b) The direction to close the choke Position: AIR CLEANER COVER (c) The direction to open the choke Position: AIR CLEAN ...

  • Zenoah BT225 - page 6

     6  5. For safe operation 1. Read this manual carefully until you completely understand and follow all safety and operating instructions. 2. Keep this manual handy so that you may refer to it later whenever any questions arise. Also note, if you have any questions which cannot be answered herein, contact the dealer from whom you purchased the ...

  • Zenoah BT225 - page 7

    b. At night, at times of heavy fog, or at any other times when your field of vision might be limited and it would be difficult to gain a clear view of the working area. c. During rain storms, during lightning storms, at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product. ■ WO ...

  • Zenoah BT225 - page 8

     8  ■ BEFORE STARTING THE ENGINE 1. The area within a perimeter of 50 feet (15m) of the person using the product should be considered a hazardous area into which no one should enter. If necessary yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more p ...

  • Zenoah BT225 - page 9

    Never place the throttle into the high speed position when starting the engine. 3. After starting the engine, check to make sure that the cutting attachment stops rotating when the throttle is moved fully back to its original position. If it continues to rotate even after the throttle has been moved fully back, turn off the engine and take the unit ...

  • Zenoah BT225 - page 10

     10  • IF SOMEONE COMES 1. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the area. Be careful if you are approached. Injury may result from flying debris. 2. If someone calls out or otherwise interrupts you while working, always be sure to turn off the engine before turning around. ■ MAIN ...

  • Zenoah BT225 - page 11

    5. For safe operation refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel. 2. Never smoke while operating the unit or refilling its fuel tank. 3. When refilling the tank, always turn off the engine and allow it to cool ...

  • Zenoah BT225 - page 12

     12  ■ MOUNTING ENGINE (SE1) 1. Loosen the bolts temporarily attached to the clutch housing. 2. Push the driveshaft toward the gearcase and rotate it by hand to check that the driveshaft is engaged with the gears. 3. Insert the shaft tube into the clutch housing until it bottoms. When difficult to engage, twist the engine slightly. 4. Align ...

  • Zenoah BT225 - page 13

    6. Set up ■ INSTALLING CUTTING HEAD (SE6) 1. While locking the gear shaft by inserting the attached bar into the upper holder and the housing. 2. Rotate the cutting head to engage threads. Hand-tighten it securely. SE6  13  ...

  • Zenoah BT225 - page 14

     14  7. Fuel ■ RECOMMENDED MIXING RATIO GASOLINE 50:OIL 1 • Exhaust emission are controlled by the fundamental engine parameters and components(eq., carburation, ignition timing and port timing) without addition of any major hardware or the introduction of an inert material during combustion. • These engines are certified to operate on ...

  • Zenoah BT225 - page 15

    7. Fuel again for at least one minute. As some oils may be difficult to agitate depending on oil ingredients, sufficient agitation is necessary for the engine to last long. Be careful that, if the agitation is insufficient, there is an increased danger of early piston seizing due to abnormally lean mixture. 5. Put a clear indication on the outside ...

  • Zenoah BT225 - page 16

     16  ■ STARTING ENGINE 1. Rest the unit on a flat, firm place. Keep the cutting head off the ground and clear of surrounding objects as it will start rotating upon starting of the engine. 2. Pump the primer until fuel flows out in the clear tube. (OP1) 3. Move the choke lever upward to close the choke. (OP2) (1) Choke lever (2) Close (3) Op ...

  • Zenoah BT225 - page 17

    8. Operation ■ STOPPING ENGINE 1. Release the throttle lever and run the engine for a half minute. 2. Shift the ignition switch to the STOP position. • Except for an emergency, avoid stopping the engine while pulling the throttle lever. ■ ADJUSTING IDLING SPEED (OP5) 1. When the engine tends stop frequently at idling mode, turn the adjusting ...

  • Zenoah BT225 - page 18

     18  3. You can avoid thrown debris by sweeping from your left to the right. 4. Use a slow, deliberate action to cut heavy growth. The rate of cutting motion will depend on the material being cut. Heavy growth will require slower action than will light growth. 5. Never swing the unit so hard as you are in danger of losing your balance or cont ...

  • Zenoah BT225 - page 19

    9. Maintenance •A lways be sure to stop the engine before inspecting the brushcutter for problems or performing maintenance. • Never alter the brushcutter or take the engine apart. •W hen replacing parts, always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax brushcutter. • Things ...

  • Zenoah BT225 - page 20

     20  9. Maintenance 8 11 14 1 2 9 10 12 13 15 THIS SIDE UP THIS SIDE UP WIND LINE ...

  • Zenoah BT225 - page 21

    •M ake sure that the engine has stopped and is cool before performing any service to the brushcutter. Contact with moving cutting head or hot muffler may result in a personal injury. ■ AIR FILTER • The air filter, if clogged, will reduce the engine performance. Monthly check and clean the filter element in warm, soapy water as required. Dry c ...

  • Zenoah BT225 - page 22

     22  ■ MUFFLER •I nspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust leakage is found, do not use the brushcutter and have it repaired immediately. • Note that failing to do so may result in the engine catching on fire. ■ SPARK ARRESTER • The muffler is equipped with a spark arreste ...

  • Zenoah BT225 - page 23

    9. Maintenance brushcutter. Note that it is necessary to remove the plug guard shown in Figure 20 in order to be able to view the upper part of the cylinder. • If waste gets stuck and causes blockage around the intake air cooling vent or between the cylinder fins, it may cause the engine to overheat, and that in turn may cause mechanical failure ...

  • Zenoah BT225 - page 24

    11 . T roubleshooting guide Case 1. Starting failure CHECK PROBABLE CAUSES ACTION fuel tank ➞ incorrect fuel ➞ drain it and with correct fuel fuel filter ➞ fuel filter is clogged ➞ clean carburetor adjustment screw ➞ out of normal range ➞ adjust to normal range sparking (no spark) ➞ spark plug is fouled/wet ➞ clean/dry ➞ plug gap ...

  • Zenoah BT225 - page 25

    12. Parts list NOTE : 1. Use KOMATSU ZENOAH genuine parts as specified in the parts list for repair and/or replacement. 2. KOMATSU ZENOAH does not warrant the machines, which have been damaged by the use of any parts other than those specified by the company. 3. When placing parts orders for repair and/or replacement, check if the model name and th ...

  • Zenoah BT225 - page 26

    12. Parts list  26  Fig.1 DRIVE UNIT BT225 (S/N 000001 and up) ...

  • Zenoah BT225 - page 27

    Key# Description Part Number Q'ty Fig.1 DRIVE UNIT BT225 (S/N 000001 and up) Key# Description Part Number Q'ty 1P IPE COMP. BT01-50810 1 2 DRIVE SHAFT BT01-50710 1 3 HOUSING ASSY BT00-50910 1 4• CASE N/A 1 5• SHAFT N/A 1 6• HOLDER N/A 1 7• SPRING WASHER, M8 BT00-50920 1 8• WASHER, M8 BT00-50960 1 9• BEARING 06002-00608 2 10 ? ...

  • Zenoah BT225 - page 28

    Fig.2 ENGINE UNIT BT225 (S/N 50100000 and up)  28  12. Parts list ...

  • Zenoah BT225 - page 29

    Key# Description Part Number Q'ty Fig.2 ENGINE UNIT BT225 (S/N 50100000 and up)  29  Key# Description Part Number Q'ty 1 CYLINDER 5580-12110 1 2 GASKET, base 5500-12213 1 3 BOLT 1850-12130 2 4 PLUG RCJ-6Y 5602-73110 1 5 CRANKCASE COMP. 5500-21100 1 6• PIN 2629-21130 3 7 GASKET 5500-21141 1 8 BEARING 06030-06001 2 9 SEAL 2169-21210 ...

  • Zenoah BT225 - page 30

    EMISSION-RELATED PARTS, FOR TWO (2) YEARS FROM THE DATE OF ORIGINAL DELIVERY OF THE UNIT, KOMATSU ZENOAH AMERICA INC. (THE COMPANY), THROUGH ANY RedMax DEALER, WILL REPAIR OR REPLACE, FREE OF CHARGE, FOR THE ORIGINAL AND EACH SUBSEQUENT PURCHASER, ANY PART OR PARTS FOUND TO BE DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP. EMISSION-RELATED PARTS ARE: TH ...

  • Zenoah BT225 - page 31

    Pièces en rapport avec les émissions de gaz d'échappement : KOMATSU ZENOAH AMERICA INC., par l'intermédiaire de n'importe quel revendeur RedMax, réparera gratuitement ou remplacera gratuitement pour l'acheteur initial et chaque acheteur successif toute(s) pièce(s) se révélant de constitution et/ou de montage défectueux ...

  • Zenoah BT225 - page 32

    ©P rinted in Japan KOMATSU ZENOAH AMERICA INC. 4344 Shackleford Road Suite 500 Norcross, Georgia 30093 ...

Fabricant Zenoah Catégorie Trimmer

Les documents que nous recevons du fabricant de l'appareilZenoah BT225 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Zenoah
- manuels d’utilisations BT225
- fiches produit Zenoah
- dépliants
- ou étiquettes-énergie Zenoah BT225
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Zenoah BT225.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Zenoah BT225, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Zenoah BT225. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Zenoah BT225.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Zenoah BT225, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Zenoah BT225 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Zenoah BT225.

Le manuel d’utilisation complet Zenoah, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Zenoah BT225 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Zenoah BT225, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lZenoah BT225 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Zenoah BT225 - qui devraient nous aider dans les premières étapes lors de l'utilisation Zenoah BT225
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Zenoah BT225
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Zenoah BT225 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Zenoah BT225?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Zenoah BT225, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Zenoah BT225 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)