Français dropdown-ico

Manuel d’utilisation Hitachi PJ-TX100

50 pages 4.05 mb
Télécharger

Aller à la page of 50

Summary
  • Hitachi PJ-TX100 - page 1

    1 ENGLISH Projector PJ-TX100 User's Manual - Operating Guide Thank you for purchasing this projector . WARNING ►Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. About this manual About this manu ...

  • Hitachi PJ-TX100 - page 2

    2 About this manual . . . . . . . . . . 1 Contents . . . . . . . . . . . . . . . . . 2 Projector features . . . . . . . . . . 3 Prepar ations . . . . . . . . . . . . . . 3 About contents of package . . . . . . . 3 Fastening the lens cover . . . . . . . . . 3 Par t names . . . . . . . . . . . . . . . 4 Projector . . . . . . . . . . . . . . . . . . . ...

  • Hitachi PJ-TX100 - page 3

    3 ENGLISH Projector features / Prepar ations Projector Projector features features This projector is used to project various computer signals as well as NTSC/P AL/ SECAP video signals onto a screen. Little space is required for installation and large images can easily be realized. This is the entertainment projector that will turn your room into a ...

  • Hitachi PJ-TX100 - page 4

    4 Par t names Lens (  34 ) radiates powerful light for projecting an image. Lens cover (  3 ) V ertical lens shift dials (  7 ) Horizontal lens shift dials (  7 ) Filter cover (  33 ) (An air fi lter is inside.) Elevator button (  7 ) is on the both sides. Elevator foot (  7 ) is on the both sides. Remote sensor (  11 ) Zoo ...

  • Hitachi PJ-TX100 - page 5

    5 ENGLISH Par t names ST ANDBY/ON button (  12 ) prepares for turning the power on/off. POWER indicator (  12 ) tells the state of power supply . MENU button (  17 ) operates the menu function. INPUT button (  13 ) toggles between the signal ports. COMPONENT VIDEO S-VIDEO VIDEO DVI-D COMPUTER POWER MENU ENTER LAMP TEMP ST ANDBY/ON INPUT ...

  • Hitachi PJ-TX100 - page 6

    6 Setting up Setting up Setting up Ar r angement WARNING ►Install the projector in a suitable environment according to instrictions of the "User's Manual - Safety Guide". CA UTION ►In installation, pay attention enough to ventilation. If internal temperature rises, it could cause malfunction. Avoid blocking vents. (about the loca ...

  • Hitachi PJ-TX100 - page 7

    7 ENGLISH Setting up Using the lens shift dials CA UTION ►Do not put your fi ngers around the projection lens to prevent them from being caught by the lens and lens ring. The Lens of this projector can be shifted horizontally and vertically . When you want to adjust the picture position, use the lens shift dials. (a) Using the horizontal picture ...

  • Hitachi PJ-TX100 - page 8

    8 Setting up Connecting your de vices WARNING ►Incorrect connecting could result in fi re or electrical shock. Whenever attempting to connect other devices to the projector , please thoroughly read the "User's Manual - Safety Guide", this manual and the manual of each device to be connected. CA UTION ►Turn of f all devices prior ...

  • Hitachi PJ-TX100 - page 9

    9 ENGLISH Setting up DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT V ...

  • Hitachi PJ-TX100 - page 10

    10 Settin up Connecting pow er suppl y WARNING ►Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fi re and/or electrical shock. • Only use the power cord that came with the projector . If it is damaged, contact your dealer to newly get correct one. • Only plug the power cord into an out ...

  • Hitachi PJ-TX100 - page 11

    11 ENGLISH Remote control Using the LIGHT button T o illuminate the buttons of the remote control, press the LIGHT button of it. 1. Press the LIGHT LIGHT button. If you don’t push the LIGHT button again, the lights will turn off in several seconds. Using the remote contr ol CA UTION ►Be careful in handling the remote control. • Do not drop or ...

  • Hitachi PJ-TX100 - page 12

    12 Po wer on/of f Power on/off Power on/off WARNING ► When the power is on, a strong light is emitted. Do not look into the lens or vents of the projector . NO TE • T urn the power on/off in right order . Please power on the projector before the connected devices. Power off the projector after the connected devices. Power switch ST ANDBY/ON but ...

  • Hitachi PJ-TX100 - page 13

    13 ENGLISH Operating Operating Operating Selecting an input signal 1. Using the projector's button, press the INPUT button. Each time you press the INPUT button, the projector switches between its input ports. Select the signal you wish to project. COMPONENT VIDEO  S-VIDEO  VIDEO  DVI-D  COMPUTER MENU ENTER INPUT RESET 1. Using the ...

  • Hitachi PJ-TX100 - page 14

    14 Operating Adjusting the zoom and f ocus 1. Use the zoom knob to adjust the screen size. 2. Use the focus knob to focus the picture. Zoom knob Focus knob Using the automatic adjustment f eature 1. Press the AUTO button (remote control). The automatic adjustment operation requires approximately 10 seconds. Also please note that it may not function ...

  • Hitachi PJ-TX100 - page 15

    15 ENGLISH Operating Selecting a mode of picture type 1. Press the MODE button (remote control) to toggle between the modes for picture type. These arrangements are combinations of a mode of GAMMA (  19 ) and a mode of COLOR TEMP (  19 ) . Choose a suitable mode according to the projected source. NORMAL  CINEMA  MUSIC  SPORTS  DYN ...

  • Hitachi PJ-TX100 - page 16

    16 Operating R ecalling your adjustment This projector can memorize 4 settings by the MY MEMORY function of the PICTURE menu (  20 ) . Pressing the MEMORY button (remote control) calls the settings and adjusts the current picture. The memory which is not registered is skipped. When there is no memory registered, the picture isn't adjusted. ...

  • Hitachi PJ-TX100 - page 17

    17 ENGLISH Multifunctional settings Multifunctional settings Multifunctional settings Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT , SETUP , SCREEN, OPTION and EASY MENU. Each of these menus is operated using the same methods. The basic operations of these menus are as follows. 1. Press the MENU button (remo ...

  • Hitachi PJ-TX100 - page 18

    18 Multifunctional settings EASY Menu EASY Menu Item Description ASPECT Select the ASPECT menu to toggle the mode of image aspect ratio. Refer to description of “ASPECT” in the “IMAGE” menu. (  22 ) KEYSTONE Perform the KEYST ONE adjustment using ◄/► buttons.: Refer to description of “KEYSTONE” in the “SETUP” menu. (  26 ) ...

  • Hitachi PJ-TX100 - page 19

    19 ENGLISH Multifunctional settings PICTURE Menu PICTURE Menu Item Description BRIGHT Adjust the brightness using the ▲/▼ buttons. : Light  Dark CONTRAST Adjust the contrast using the ▲/▼ buttons. : Strong  Wea k GAMMA Select a GAMMA mode using the ▲/▼ button. : #1 DEF AUL T  #1 CUST OM  #2 DEF AUL T  #2 CUSTOM #4 CUSTOM ...

  • Hitachi PJ-TX100 - page 20

    20 Multifunctional settings Item Description SHARPNESS Adjust the sharpness using the ▲/▼ buttons. : Clear  Soft PROGRESSIVE Select the Progressive Mode: TV  FILM  TURN OFF memo This function performs only at an interlaced signal of a VIDEO input, a S-VIDEO input or a COMPONENT VIDEO input of 525i or 625i signal. The FILM mode is adapt ...

  • Hitachi PJ-TX100 - page 21

    21 ENGLISH Multifunctional settings PICTURE Menu (continued) Adjustment steps of the CUSTOM GAMMA or the CUSTOM COLOR TEMP Press the ENTER button while the CUSTOM menu of “GAMMA” or “COLOR TEMP” is displayed. And the test pattern appears at the top of the screen as shown in the right. Each time you press the ENTER button, the pattern change ...

  • Hitachi PJ-TX100 - page 22

    22 Multifunctional settings IMAGE Menu IMAGE Menu Item Description ASPECT Select an Aspect Ratio using the ▲/▼ buttons: At a COMPUTER input: 4:3  16:9  NORMAL • The NORMAL keeps the original aspect ratio of the input signal. • At a COMPUTER input, selecting an aspect ratio may display the message“SYNC IS OUT OF RANGE”. In this cas ...

  • Hitachi PJ-TX100 - page 23

    23 ENGLISH Multifunctional settings Item Description H SIZE Adjust the horizontal size using the ▲/▼ buttons. : Large  Small memo This item can be selected only at a RGB signal. memo When this adjustment is excessive, the picture may not be displayed correctly . In such a case, please reset the adjustment pressing the RESET button during thi ...

  • Hitachi PJ-TX100 - page 24

    24 Multifunctional settings INPUT Menu INPUT Menu Item Description COLOR SP ACE Select a color space mode using the ▲/▼ buttons. : AUTO  RGB  SMPTE240  REC709  REC601 Selecting the AUTO automatically selects the optimum mode. memo This item can not be selected only at a VIDEO or a S-VIDEO signal. memo The AUTO operation may not work ...

  • Hitachi PJ-TX100 - page 25

    25 ENGLISH Multifunctional settings Item Description INFORMA TION Pressing the ► (or the ENTER) button displays the INPUT INFORMA TION menu. The INPUT INFORMA TION menu shows the information about the current signal input as illustrated below . memo The “FRAME LOCK” message means the frame lock function is working. This function automatically ...

  • Hitachi PJ-TX100 - page 26

    26 Multifunctional settings SETUP Menu SETUP Menu Item Description KEYSTONE Adjust the Keystone (V ertical) Distortion: Upper in the data  Lower in the data memo The adjustable range of this function will vary with the type of input signal. At some signals, this function may not work well. memo When the V :INVERT or the H&V :INVERT is select ...

  • Hitachi PJ-TX100 - page 27

    27 ENGLISH Multifunctional settings SCREEN Menu SCREEN Menu Item Description LANGUAGE Select a menu language using the ▲/▼ buttons. : ENGLISH  FRANÇAIS  DEUTSCH  ESP AÑOL  IT ALIANO NORSK  NEDERLANDS  PORTUGUÊS    SVENSKA   SUOMI  POLSKI MENU POSITION Adjust the menu position using the ▲/▼/◄/► butt ...

  • Hitachi PJ-TX100 - page 28

    28 Multifunctional settings Item Description MESSAGE Select the TURN ON or the TURN OFF using the ▲/▼ buttons. : TURN ON  TURN OFF When the TURN ON is selected, the following message function works. The message of the “AUTO IN PROGRESS” for the auto adjustment. The message of the ”NO INPUT IS DETECTED” The message of the ”SYNC IS O ...

  • Hitachi PJ-TX100 - page 29

    29 ENGLISH Multifunctional settings OPTION Menu OPTION Menu Item Description AUTO OFF Set the time using the ▲/▼ buttons. : Long (max. 99 minutes)  Short (min. 0 minute = DISABLE) ex. When the time is set to 1 to 99, the projector lamp will go off and the power indicator begins blinking when the passed time with a proper signal (without no-s ...

  • Hitachi PJ-TX100 - page 30

    30 Multifunctional settings Item Description SERVICE Pressing the ► (or the ENTER) button calls the SERVICE menu. SERVICE Menu Select an item using the ▲/▼ buttons, and press the ► (or the ENTER) button to perform each function. : F ANSPEED  F ACTORY RESET F ANSPEED Select the fan speed level using the ▲/▼ buttons. : HIGH  LOW The ...

  • Hitachi PJ-TX100 - page 31

    31 ENGLISH Maintenance Maintenance Maintenance LAMP WARNING HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn ...

  • Hitachi PJ-TX100 - page 32

    32 Maintenance Lamp If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1. T urn off the projector , and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes. 2. C ontact your dealer to prepare a new lamp. T ell the dealer your lamp type number: DT00661 . If the projector is mo ...

  • Hitachi PJ-TX100 - page 33

    33 ENGLISH Maintenance Air fi lter WARNING ►Before replacing the lamp, make sure the power switch is off and the power cord is not plugged in, then wait at least 45 minutes for the lamp to cool suffi ciently . ►Use only the air fi lter of the specifi ed type. Do not use the projector with the air fi lter and fi lter cover removed. CA UTIO ...

  • Hitachi PJ-TX100 - page 34

    34 Maintenance WARNING ►Please carefully read the "User's Manual - Safety Guide". ►Before caring, make sure the power switch is off and the power cord is not plugged in. ►Be cautious of high temperature. Do not touch about the lens and ventilation openings during use or immediately after prevent a burn. ►Never try to care for ...

  • Hitachi PJ-TX100 - page 35

    35 ENGLISH T r oubleshooting T roubleshooting T roubleshooting R elated messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please respond as described below . If the same message is displayed after the treatment, or if a message other than the following a ...

  • Hitachi PJ-TX100 - page 36

    36 T r oubleshooting Related messages (continued) Message Description SYNC IS OUT OF RANGE ON *** fH *****kHz fV *****Hz The horizontal or vertical wavelength of the inputted signal is outside of the response parameters of this unit. Please confi rm the specs for this unit or the signal source specs. CHECK THE AIR FLOW The internal portion tempera ...

  • Hitachi PJ-TX100 - page 37

    37 ENGLISH T r oubleshooting R e garding the indicator lamps Lighting and fl ashing of the POWER indicator , the LAMP indicator , and the TEMP indicator have the meanings as described in the table below . Please respond in accordance with the instructions within the table. If the same indication is displayed after the treatment, or if an indicatio ...

  • Hitachi PJ-TX100 - page 38

    38 T r oubleshooting Regarding the indicator lamps (continued) POWER indicator LAMP indicator TEMP indicator Description Blinking In Red or Lighting In Red T urned off Blinking In Red The cooling fan is not operating. Please turn the power off, and allow the unit to cool down at least 20 minutes. After the projector has suffi ciently cooled down, ...

  • Hitachi PJ-TX100 - page 39

    39 ENGLISH T r oubleshooting Phenomena that may easily be mistak en for machine def ects WARNING ►Never use the projector if abnormal operations such as smoke, strange odor , excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter , etc. should occur . In such cases, immediately turn off the power switch an ...

  • Hitachi PJ-TX100 - page 40

    40 Phenomena that may easily be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect Reference page No pictures are displayed. The PC cannot detect the projector as a plug and play monitor . Make sure that the PC’s can detect a plug and play monitor using other plug and play monitor . 8 If the connected PC has ...

  • Hitachi PJ-TX100 - page 41

    41 ENGLISH Warr anty And After-Ser vice W arranty and after-service W arranty and after-service If a problem occurs with the equipment, fi rst refer to the “Troubleshooting” and run through the suggested checks. If this does not resolve the problem, please contact your dealer or the service company . They will tell you what warranty condition ...

  • Hitachi PJ-TX100 - page 42

    ...

  • Hitachi PJ-TX100 - page 43

    1 ENGLISH Projector PJ-TX100 PJ-TX100W/E/U Users Manual - Qui c k Guide Thank you for purchasing this projector . WARNING ►Before using, read the "User's Manual - Safety Guide" and these manuals to ensure correct usage through understanding. After reading, store them in a safe place for future reference. NO TE • The information i ...

  • Hitachi PJ-TX100 - page 44

    2 Ar rangement / Adjusting the pr ojector's ele vator Arrangement Arrangement WARNING ►Install the projector in a suitable environment according to instrictions of the "User's Manual - Safety Guide". CA UTION ►This projector has some intake vents also on the bottom. Avoid blocking vents. Put nothing that is sucked or sticks ...

  • Hitachi PJ-TX100 - page 45

    3 ENGLISH Connecting your de vices Connecting your devices Connecting your devices DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDEO VIDEO COMPUTER CONTROL DVI-D Y C B /P B C R /P R COMPONENT VIDEO S-VIDE ...

  • Hitachi PJ-TX100 - page 46

    4 Connecting the power supply / Putting batteries into the remote control Connecting the power supply Connecting the power supply WARNING ►Please use extra caution when connecting the power cord as incorrect or faulty connections may result in fi re and/or electrical shock. • Only use the power cord that came with the projector . If it is dama ...

  • Hitachi PJ-TX100 - page 47

    5 ENGLISH Operating Operating Operating WARNING ►When the power is on, a strong light is emitted. Do not look into the lens or vents of the projector . T ur ning on the pow er 1. Set the power switch to the ON position. 2. Press the button ST ANDBY/ON (projector) or POWER (remote control). Displaying 1. T o select an input signal, use the button ...

  • Hitachi PJ-TX100 - page 48

    6 Lamp Lamp Lamp WARNING HIGH VOL T AGE HIGH TEMPERA TURE HIGH PRESSURE ►The projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out , if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using the ...

  • Hitachi PJ-TX100 - page 49

    7 ENGLISH Lamp (continued) Lamp replacement If the indicators or a message prompts you to replace the lamp, replace the lamp as soon as possible. 1. T urn off the projector , and unplug the power cord. Allow the lamp bulb to cool for at least 45 minutes. 2. Contact your dealer to prepare a new lamp. T ell the dealer your lamp type number: DT00661 D ...

  • Hitachi PJ-TX100 - page 50

    8 Air fi lter Air fi lter Air fi lter WARNING ►Before replacing the lamp, make sure the power switch is off and the power cable is not plugged in, then wait at least 45 minutes for the lamp to cool suffi ciently . ►Use only the air fi lter of the specifi ed type. Do not use the projector with the air fi lter and fi lter cover removed. C ...

Fabricant Hitachi Catégorie Projector

Les documents que nous recevons du fabricant de l'appareilHitachi PJ-TX100 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hitachi
- manuels d’utilisations PJ-TX100
- fiches produit Hitachi
- dépliants
- ou étiquettes-énergie Hitachi PJ-TX100
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hitachi PJ-TX100.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hitachi PJ-TX100, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hitachi PJ-TX100. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hitachi PJ-TX100.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hitachi PJ-TX100, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hitachi PJ-TX100 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hitachi PJ-TX100.

Le manuel d’utilisation complet Hitachi, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hitachi PJ-TX100 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hitachi PJ-TX100, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHitachi PJ-TX100 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hitachi PJ-TX100 - qui devraient nous aider dans les premières étapes lors de l'utilisation Hitachi PJ-TX100
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hitachi PJ-TX100
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hitachi PJ-TX100 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hitachi PJ-TX100?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hitachi PJ-TX100, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hitachi PJ-TX100 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)