Français dropdown-ico

Manuel d’utilisation Hobart HFD50 ML-135551

28 pages 0.93 mb
Télécharger

Aller à la page of 28

Summary
  • Hobart HFD50 ML-135551 - page 1

    MODEL HFD/HFC SERIES ELECTRIC FRYERS MODELS HFD50 ML-135551 HFD85 ML-135553 HFC50 ML-135555 HFC85 ML-135558 HFO15 ML-135558 HFO21 ML-135559 FORM 35612 (08-03) 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 ...

  • Hobart HFD50 ML-135551 - page 2

    — 2 — TABLE OF CONTENTS GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Unpacking ...

  • Hobart HFD50 ML-135551 - page 3

    — 3 — Installation, Operation and Care of MODEL HFD/HFC SERIES ELECTRIC FRYERS SAVE THESE INSTRUCTIONS FOR FUTURE USE GENERAL Hobart HFD/HFC Series Electric Fryers are available in 2 sizes with an array of features and options for a range of commercial fryer applications. Width Fry Compound Model KW Inches / cm Lb / kg HFD/HFC50 17 15 1 / 2 / 3 ...

  • Hobart HFD50 ML-135551 - page 4

    — 4 — HF Series Fryer — Construction Features Model Filter Ready Battery Battery Configuration Interplumbing HFD50/HFC50 Opt. (Use HMF50) Opt. Opt. HFD85/HFC85 Opt. (Use HMF85) Opt. Opt. Model Fat Melt Thermostat Basket Lift(s) Basket(s) Cycle Twin Single Tri HFD50 Std. Solid State Opt. Std. Opt. N/A HFD85 Digital Display Std. Opt. Opt. HFC50 ...

  • Hobart HFD50 ML-135551 - page 5

    — 5 — HFO Series Frymate — Finish Options Model HFO15, HFO21 Front Door Legs Standard Stainless Steel Stainless Steel Legs Optional Not Applicable Casters * Model HFO15 is for use with the HF50 Series Fryers. Model HFO21 is for use with the HF85 Series Fryers. HFO Series Frymate — Features Tops Heat Lamp Drain Solid Pan Solid Pan Perforated ...

  • Hobart HFD50 ML-135551 - page 6

    — 6 — INSTALLATION Before installing the fryer, verify that the electrical service agrees with the specifications on the fryer data plate which is located on the inside of the door panel. If the supply and equipment requirements do not agree, do not proceed with the installation. Contact your dealer or Hobart Corporation immediately. UNPACKING ...

  • Hobart HFD50 ML-135551 - page 7

    — 7 — Fig. 1 LEVELING Place a carpenter's level on top of the fryer and level the fryer front-to-back and side-to-side by turning the adjustable legs or casters. ELECTRICAL CONNECTIONS WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL CODES. WARNING: DISCONNECT THE ELECTRICAL POW ...

  • Hobart HFD50 ML-135551 - page 8

    — 8 — OPERATION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK. BEFORE FIRST USE Clean the Fryer and Heating Elements Do not operate fryer without frying compo ...

  • Hobart HFD50 ML-135551 - page 9

    — 9 — ADDING SOLID SHORTENING If replacing shortening, place the block of shortening in the room with the fryer for 1 to 2 hours before using. This will soften the shortening and make it easier to divide. CAUTION: Failure to remove crumb screens prior to addition of fresh shortening may cause heating elements to overheat, allowing shortening to ...

  • Hobart HFD50 ML-135551 - page 10

    — 10 — CONTROLS — Control Guide HFD SERIES (MANUFACTURED AFTER AUGUST 2003 WITH TDI CONTROLLERS) — Power switch; for turning the fryer on or off. — For cleaning purposes when the fryer is filled with water. Temperature is maintained at approxmiately 192°F (89°C).** — For entering and exiting the program mode. For scrolling through pro ...

  • Hobart HFD50 ML-135551 - page 11

    — 11 — PARAM ETER SELECT DISPLAY SCROLL Left Timer P re ss or to en ter ti me . LED is lit above the left ba sket icon . The ti me val ue is di splay ed in window. Pr es s a nd scroll to next item . Right Timer Pr es s o r to en te r t i me . LED is lit ab ove the right bas k et icon . The ti me val ue is di splay ed in window. Pr es s a nd scr ...

  • Hobart HFD50 ML-135551 - page 12

    — 12 — Melt Options (HFD Series) When using solid shortening in the fryer, the CY S (solid shortening) option must be used. Solid shortening must be gently warmed to a liquid state before heating to frying temperatures. Melting solid shortening without using this option will damage the fry tank and scorch the shortening. The controller has thre ...

  • Hobart HFD50 ML-135551 - page 13

    — 13 — USING THE FRYER (After Startup) Models Without Basket Lift Option 1. Load the fry basket(s); do not overfill. 2. Carefully lower basket(s) into shortening. 3. Press to start the left timer. Press to start the right timer. 4. When the timer times out, a beeper sounds. Press to silence the left timer beeper. Press to silence the right time ...

  • Hobart HFD50 ML-135551 - page 14

    — 14 — Control Guide CONTROLS — HFC SERIES (MANUFACTURED AFTER AUGUST 2003 WITH TDI CONTROLLERS) — Power switch; for turning the fryer on or off. — For setting fry temperature. For viewing shortening temperature and set temperature. — For entering and exiting the program mode. — For selecting program parameters. For setting timers 1 t ...

  • Hobart HFD50 ML-135551 - page 15

    — 15 — PARAMETER STEPS LEFT DISPLAY RIGHT DISPLAY Press SELECT OPTIONS Press DEGREES F or C F or C Press to select Fahrenheit or Celsius. DEGREES F or C F or C Press when complete. PROGRAM Press SELECT OPTIONS Press SET PASS NEW PASS Press to select NO PASS. NO PASS NEW PASS Press when complete. PROGRAM Press SELECT OPTIONS Press SET PASS NEW P ...

  • Hobart HFD50 ML-135551 - page 16

    — 16 — PARAMETER STEPS LEFT DISPLAY RIGHT DISPLAY Press SELECT OPTIONS Press ENGLISH (Factory Default) LANGUAGE Press to select a language. ENGLISH/ESPANOL FRANCAIS/DEUTSCH HOLLAND Press when complete. PROGRAM Press SELECT OPTIONS Press NO MELT/LIQUID/SOLID Press to select melt options. NO MELT/LIQUID/SOLID Press when complete. PROGRAM Press SE ...

  • Hobart HFD50 ML-135551 - page 17

    — 17 — Melt Options (HFC Series) When using solid shortening in the fryer, the SOLID melt option must be used. Solid shortening must be gently warmed to a liquid state before heating to frying temperatures. Melting solid shortening without using this option will damage the heating elements and scorch the shortening. The controller has three opt ...

  • Hobart HFD50 ML-135551 - page 18

    — 18 — TEMPERATURE AND TIME PROGRAMMING Temperature 1. Press to enter program mode. PROGRAM is displayed in the window. 2. Press to enter temperature mode. 000°F and TEMP are displayed in the window. 3. Press through to enter desired fry temperature. The fry temperature is displayed in the window. 4. Press to exit the temperature mode. Press a ...

  • Hobart HFD50 ML-135551 - page 19

    — 19 — Setting Advanced Time Features 1. Press and enter the program mode. 2. Press for timers through , or press for timers through . The LEDs are lit on the timers available for programming, and SELECT PRODUCT is displayed in the window. 3. Select a timer; the programmed time is displayed in the window. A. Duty Time : 1) Press either arrow on ...

  • Hobart HFD50 ML-135551 - page 20

    — 20 — USING THE FRYER (After Startup) Models Without Basket Lift Option 1. Load the fry basket(s), do not overfill. 2. Carefully lower basket(s) into shortening. 3. Press the desired number to select the product to be timed. Timers through are programmed for products. Once the product is selected, select or button to start timing of the produc ...

  • Hobart HFD50 ML-135551 - page 21

    — 21 — FRYING (All Models) Heat shortening to set temperature. Pieces of product to be fried should be about the same size to ensure the same doneness. Drain or wipe dry raw or wet foods to minimize splatter when lowering into the hot oil. Do not overfill baskets. Recommended maximum capacities are: Lb / kg of Total Lb / kg Total Lb / kg Produc ...

  • Hobart HFD50 ML-135551 - page 22

    — 22 — DAILY FILTERING Fryers Without Filter Ready Options Turn power switch off when draining or filling. Always filter the shortening while liquified. A cold fryer will not drain properly because the shortening under the cold zone tube area will remain hard, even if the heat is on for a few minutes. If necessary, the clean-out rod may be used ...

  • Hobart HFD50 ML-135551 - page 23

    — 23 — CLEANING (All Models) WARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY TO THE MACHINE AND FOLLOW LOCKOUT/TAGOUT PROCEDURES. Daily Clean the exterior of your fryer regularly with a damp cloth and polish with a soft dry cloth. If regular cleaning is neglected, grease will be burned on and discolorations may form. These may be removed by was ...

  • Hobart HFD50 ML-135551 - page 24

    — 24 — CLEANING (CONTINUED) Weekly or as Required 1. Once the shortening has been drained, flush out scraps and sediment with a small amount of warm shortening. Allow the tank to drain thoroughly. 2. Close the drain valve and fill the tank with a non-corrosive, grease-dissolving commercial cleaner, following the manufacturer's instructions ...

  • Hobart HFD50 ML-135551 - page 25

    — 25 — TROUBLESHOOTING ALARMS AND ERROR MESSAGES O pen Probe - If an open probe is detected, the heat demand is disabled and any running cooking cycles are cancelled. All operator buttons are disabled. The control displays the following message: HFD Models - Prob HFC Models - OPEN PROBE The alarm sounds continuously until the fault clears or th ...

  • Hobart HFD50 ML-135551 - page 26

    — 26 — MAINTENANCE WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK. LUBRICATION Motors used on basketlifts are permanently lubricated. SERVICE AND PARTS INFORMA ...

  • Hobart HFD50 ML-135551 - page 27

    — 27 — NOTES ...

  • Hobart HFD50 ML-135551 - page 28

    — 28 — FORM 35612 (08-03) PRINTED IN U.S.A. NOTES ...

Fabricant Hobart Catégorie Fryer

Les documents que nous recevons du fabricant de l'appareilHobart HFD50 ML-135551 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Hobart
- manuels d’utilisations HFD50 ML-135551
- fiches produit Hobart
- dépliants
- ou étiquettes-énergie Hobart HFD50 ML-135551
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Hobart HFD50 ML-135551.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Hobart HFD50 ML-135551, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Hobart HFD50 ML-135551. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Hobart HFD50 ML-135551.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Hobart HFD50 ML-135551, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Hobart HFD50 ML-135551 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Hobart HFD50 ML-135551.

Le manuel d’utilisation complet Hobart, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Hobart HFD50 ML-135551 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Hobart HFD50 ML-135551, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHobart HFD50 ML-135551 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Hobart HFD50 ML-135551 - qui devraient nous aider dans les premières étapes lors de l'utilisation Hobart HFD50 ML-135551
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Hobart HFD50 ML-135551
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Hobart HFD50 ML-135551 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Hobart HFD50 ML-135551?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Hobart HFD50 ML-135551, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Hobart HFD50 ML-135551 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)