Manuel d’utilisation Chamberlain 9902

40 pages 1.13 mb
Télécharger

Aller à la page of 40

Summary
  • Chamberlain 9902 - page 1

    Garage Door Opener Model 9902 1/2 HP For Residential Use Only Owner ’ s Manual ■ Please read this manual and the enclosed safety materials car efully! ■ Fasten the manual near the garage door after installation. ■ The door WILL NOT CLOSE unless the Protector System ® is connected and properly aligned. ■ Periodic checks of the opener are ...

  • Chamberlain 9902 - page 2

    Start by re viewing these important safety alert symbols: 2 Safety alert symbol re view ............................................2 Safety information, precautions, tools ..........................3 T esting your garage door for binding & balance ..........3 Carton in ventory ...........................................................4 Hardwa ...

  • Chamberlain 9902 - page 3

    3 Sectional Door One-Piece Door Pliers Wire Cutters Claw Hammer Hack Saw Screwdriver 1/2" & 7/16" Sockets and Wrench Drill Tape Measure 1/2" x 7/16" Box Wrench 2 1 Stepladder Pencil 3/16", 5/16" and 5/32" Drill Bits Carpenter's Level During assembly , installation and adjustment of the opener , instructio ...

  • Chamberlain 9902 - page 4

    4 Straight Door Arm Section Curved Door Arm Section Header Bracket UP CEILING MOUNT ONLY Remote Control Transmitter Visor Clip Sprocket Coupling Rail Assembly 2-Conductor Bell Wire White & White/Red Light Lens Header/Rail Brackets Trolley Rail Support Braces (4) Hanging Brackets Safety Labels and Literature Door Bracket SECURITY ✚ Multi-Funct ...

  • Chamberlain 9902 - page 5

    Hardware 5 Separate all hardware fr om the packages in the rail carton and the opener carton and group as shown below , for the assembly and installation procedur es. Lock Nut 1/4"-20 x 7/16 (12) Wing Nut (2) Carriage Bolt 1/4"-20x1/2" (2) 1/4" - 20 x 5/8" Hex Screw (4) Sprocket Coupling Sleeve Assembly Hardware Bolt 1/4-20 ...

  • Chamberlain 9902 - page 6

    6 Header Bracket Rail Bracket Trolley Straight Door Arm Manual Release Rope & Handle Door Bracket Garage Door Curved Door Arm Garage Door Spring Header Wall Rail Assembly Closed Position Safety Reversing Sensor Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, steel, aluminum, door with glass panels, etc. ...

  • Chamberlain 9902 - page 7

    7 Safety Reversing Sensor FINISHED CEILING Support bracket & fastening hardware is required. See page 20. Safety Reversing Sensor Header Wall Access Door Gap between floor and bottom of door must not exceed 1/4". Closed Position Header Bracket Trolley Straight Door Arm Manual Release Rope & Handle Door Bracket Curved Door Arm Header Wa ...

  • Chamberlain 9902 - page 8

    8 Center Rail Trolley Rack Extend End Rails Outward Extend End Rails Outward Rail Assembly Carton Remove Cardboard Packing Remove Cardboard Packing Rail Support Braces Straight Door Arm Rail Assembly Hardware Bag Chassis Assembly Hardware Bag ASSEMBL Y STEP 1 Assemble the Rail Assembly Section: Pages 8 - 1 1 Center Rail Door End Rail Rail Sprocket ...

  • Chamberlain 9902 - page 9

    9 Center Rail Slide End Rails Towards Center Rail Slide End Rails Towards Center Rail Rail Support Brace Lock Nuts Center Rail Rail Pin Alignment Hole Rail Support Brace Rail Pin Rail Pin Alignment Hole Alignment Hole 1/4x20x1-3/4" Bolts 1/4x20x1-3/4" Bolts Lock Nuts End Rail Door End Sprocket End 4. Be ginning with the sprocket end, stra ...

  • Chamberlain 9902 - page 10

    10 ASSEMBL Y STEP 2 Fasten the Rail T o the Power Unit and Install the Trolley /7/94 Rail Sprocket Rail Assembly Trolley Coupling Rail/Power Unit Bracket Lock Nuts 1/4"-20 Power Unit Sprocket Power Unit Foam Packaging Hex Screws 1/4"-20x5/8" 1/4" - 20 Lock Nut 1/4" - 20 x 5/8" Hex Screw Hardware Shown Actual Size As il ...

  • Chamberlain 9902 - page 11

    ASSEMBL Y STEP 3 Attach the Rail Brackets 11 IMPORT ANT INST ALLA TION INSTRUCTIONS T o r educe the risk of severe injury or death to persons: 1. READ AND FOLLOW ALL INST ALLA TION INSTRUCTIONS 2. Install only on a properly balanced and lubricated garage door . An improperly balanced door may not reverse and could result in severe injury or death. ...

  • Chamberlain 9902 - page 12

    Header Wall Ceiling Track Highest Point of Travel Door Door Track 3" Header Wall Highest Point of Travel 3" 12 Vertical Guideline Finished Ceiling Vertical Guideline Header Wall 2x4 Structural Supports SECTIONAL Door or ONE PIECE Door with T rack • Close the door and mark the inside vertical centerline of the garage door . • Extend th ...

  • Chamberlain 9902 - page 13

    Header Wall Vertical Centerline Vertical Centerline of Garage Door 2x4 Unfinished Ceiling Structural Supports 2x4 Header Support OPTIONAL CEILING MOUNT FOR HEADER BRACKET • Close the door and mark the inside vertical centerline of your garage door . Extend the line onto the header wall abov e door . If headroom clearance is minimal, you can insta ...

  • Chamberlain 9902 - page 14

    Lag Screws 5/16"x9x1-5/8" Highest Point of Travel (of Garage Door) Vertical Center Line Header Wall Garage Door UP CEILING MOUNT ONLY Wall Mounting Holes Optional Wall Mounting Holes The nail hole is for positioning only. You must use lag screws to mount the header bracket. UP CEILING MOUNT ONLY Door Spring Header Bracket 2x4 Structural S ...

  • Chamberlain 9902 - page 15

    Header Bracket Rail Bracket Foam Packaging Opener Carton or Temporary Support Header Wall Garage Door Rail Clevis Pin 5/16" x 2-3/4" Ring Fastener Clevis Pin 5/16"x2-3/4 " Ring Fastener Header Bracket Rail Bracket Rail • Position the opener on the garage floor belo w the header bracket. Use packing material as a protecti ve ba ...

  • Chamberlain 9902 - page 16

    Without a properly working safety reversing sensor, persons (particularly children) could be injured or killed by a closing garage door. Read and follow all instructions. To protect small children, install the safety reversing sensor so that the beam will be no higher than 4"-6" above the garage floor. Disconnect power to the garage door ...

  • Chamberlain 9902 - page 17

    Installation Step 4 Install the Safety Reversing Sensor (Receiving and Sending Eyes) 17 FLOOR MOUNT (Right Side) WALL MOUNT (Right Side) DOOR TRACK MOUNT (Right Side) Indicator light Lens Lip Sensor Brack et Door T rac k Sensor Brack et Optional Extension Bracket (See Accessories) Lens Indicator light Attach with concrete anchors (not provided) Ins ...

  • Chamberlain 9902 - page 18

    18 Installation Step 4 (Continued) Install the Safety Reversing Sensor Invisible Light Beam Protection Area Sensor Sensor Bell Wire Foam Packaging Carton 2. Run wires along channels to power unit and pull taut. 1. Run wires from sensors to end of rail at the door header. Cross & twist here to help contain wires in channels on top of rail. 3. Th ...

  • Chamberlain 9902 - page 19

    Installation Step 5 Position the Opener Follow instructions which apply to your door type as illustrated. To prevent damage to steel, aluminum, fiberglass or glass panel doors, do not rest the opener on the door without using a 2x4. SECTIONAL Door or ONE-PIECE Door with T rack A 2x4 laid flat is convenient for setting an ideal door - to-rail distan ...

  • Chamberlain 9902 - page 20

    Installation Step 6 Hang the Opener T wo repr esentative installations are shown. Y ours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener . The bracket and fastening har dwar e ar e not supplied. ...

  • Chamberlain 9902 - page 21

    Installation Step 7 Install the Door Control and Connect all Wiring 21 Locate the door control within sight of the door at a minimum height of 5 feet where small childr en cannot reach, and away fr om all moving parts of the door and door hardware. The multi-function door control is typically attached directly to the wall, see Figure 1. For pre-wir ...

  • Chamberlain 9902 - page 22

    Aligning the Safety Sensors • Plug in the opener . The indicator lights in both the sending and receiving eyes will glow steadily if wiring connections and alignment are correct. The sending eye orange indicator light will glow regardless of alignment or obstruction. If the green indicator light in the r eceiving eye is off, dim, or flickering (a ...

  • Chamberlain 9902 - page 23

    Installation Step 10 Install the Lights and Lens Installation Step 1 1 Attach the Manual Release Rope and Handle Do not use the red handle to pull the door open or closed. The rope knot could become untied and you could fall. Use the manual release only to disengage the trolley and, if possible, only when the door is closed. Garage doors are heavy. ...

  • Chamberlain 9902 - page 24

    Installation Step 12 Fasten Door Bracket Follow instructions which apply to your door type as illustrated below or on page 25. T o prevent dama g e to steel, aluminum, fiber glass or glass panel doors, al ways reinfor ce the inside of the door both vertically and horizontally with an angle ir on. A horizontal brace should be long enough to be secur ...

  • Chamberlain 9902 - page 25

    Horizontal and vertical reinforcement is needed for lightweight garage doors (fiberglass, aluminum, steel, door with glass panel, etc.). (Not Provided) Header Wall Vertical Centerline of Garage Door Finished Ceiling Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 Support For a door with no exposed framing or for the optional inst ...

  • Chamberlain 9902 - page 26

    Installation Step 13 Connect Door Arm to Trolley F ollow instructions which apply to your door type as illustrated below and on page 27. Make sur e garage door is fully closed. Pull the manual release handle to disconnect the outer trolley fr om the inner trolley . Slide the outer trolley back (away from the door) about 2" as sho wn in Figures ...

  • Chamberlain 9902 - page 27

    Door Arm Fully Open Trolley Closed Door Open Door Door with Backward Slant Door Arm Connector Hole Door Arm Connector Hole Fully Closed Trolley Door Arm Nuts 5/16"-18 Lock Washers 5/16" Ring Fastener Straight Arm Screws 5/16"-18x7/8 Door Bracket Clevis Pin 5/16"x1-1/4" Curved Door Arm All ONE-PIECE Doors Assemble the Door A ...

  • Chamberlain 9902 - page 28

    Adjustment Step 1 Adjust the UP and DOWN Limits Do not make any limit adjustments until the safety re versing sensors are completely installed. 28 Limit adjustment settings regulate the points at which the door will stop when moving up or do wn. The door will stop in the up direction if anything interferes with door trav el. The door will r everse ...

  • Chamberlain 9902 - page 29

    Adjustment Step 2 Adjust the Force Too much force on the door will interfere with the proper operation of the safety reverse system. The door might not reverse properly when required and could seriously injure or kill someone under it. Do not increase the force beyond the minimum amount required to close the door. Do not use the force adjustments t ...

  • Chamberlain 9902 - page 30

    Adjustment Step 4 T est the Safety Reverse System T est • W ith the door fully open, place a one-inch board (or a 2x4 laid flat) on the floor , centered under the garage door . • Operate the door in the down direction. The door must reverse on striking the obstruction. Adjustment If the door stops on the obstruction, it is not traveling far eno ...

  • Chamberlain 9902 - page 31

    Once a Month Manually operate door . If it is unbalanced or binding, call for professional garage door service. Check to be sure door opens & closes fully . Adjust limits and/or force if necessary . (See pages 28 & 29.) Repeat the safety re verse test. Make an y necessary adjustments (See page 30). Once a Y ear Oil door rollers, bearings an ...

  • Chamberlain 9902 - page 32

    32 Activate the opener with any of the f ollowing: • The Remote Control T ransmitter . Hold the lar ge push button do wn until the door starts to mov e. • The Door Control. Hold push bar do wn until the door starts to mov e. • The Outside K eylock or Keyless Entry . (See Accessories) When the opener is activated with the safety r eversing sen ...

  • Chamberlain 9902 - page 33

    Children operating or playing with a garage door opener can injure themselves or others. The garage door could close and cause serious injury or death. Do not allow children to operate the door control(s) or remote control transmitter(s). A moving garage door could injure or kill someone under it. Activate the opener only when you can see the door ...

  • Chamberlain 9902 - page 34

    1. Does the opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker . (Some outlets are controlled by a wall switch.) 2. Have you disabled all door locks? Review installation instruction warnings on Page 1 1. 3. Is there a build-up of ice or snow under the door? The door may be fr ...

  • Chamberlain 9902 - page 35

    Having a Problem? (continued) Situation Probable Cause & Solution The door reverses for no apparent reason and opener lights don't blink: The door reverses for no apparent reason and opener lights blink for 5 seconds after reversing: 1. Is something obstructing the door? Pull the manual release handle. Operate the door manually . If it is ...

  • Chamberlain 9902 - page 36

    11 5 NOTICE 6 10 12 7 UP CEILING MOUNT ONLY 8 4 3 2 1 LOCK LIGHT 9 13 3 1 5 8 10 7 2 9 4 6 Rail Assembly Parts Installation Parts 36 KEY PART NO. NO. DESCRIPTION 1 41A4796 Hardware bag 2 41A4795 Hardware bag (includes sprocket coupling) 3 12B569-1 Left rail bracket 4 12B569-2 Right rail bracket 5 1C4827-1 Screw drive rail assembly 6 12B560 Rail sup ...

  • Chamberlain 9902 - page 37

    Repair Parts 37 ew crew Drive 2/94 DN UP Brown Wire (Down) Contact LIMIT SWITCH ASSY. Grey Wire Yellow Wire (Up) Contact Center Limit Contact Drive Gear 2 1 4 5 7 13 17 16 9 12 8 14 15 10 6 11 3 8c 8a 8b 8d Opener Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 31D426 Drive shaft cover 2 41B4245 Line cord 3 30B363 Capacitor – 1/2 HP 4 12A373 Capac ...

  • Chamberlain 9902 - page 38

    LOCK LIGHT LOCK LIGHT 953CB 956CB 935CB 41A5281 Motion Detecting Control Panel: Multi-function door control with motion sensor that automatically turns opener lights on for 5 minutes when it detects a person entering the garage. Sensor can be easily deactivated when desired. 940CB SECURITY ✚ Keyless Entry: Enables homeowner to operate garage door ...

  • Chamberlain 9902 - page 39

    Index Access Door/Outside Quick Release Accessory .................................................................................................6, 7, 35, 36 Electrical Safety W arnings ......................................................................................................................................2, 22, 31 Garage Door T esti ...

  • Chamberlain 9902 - page 40

    © 2000, The Chamberlain Group, Inc. 114A2305B All Rights Reserved Printed in Mexico CHAMBERLAIN SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE SIX DAYS A WEEK. SIMPLY DIAL OUR TOLL FREE NUMBER: 1-800-528-9131 HOURS: (Central Standard Time) 6:00 A.M. TO 7:00 P.M. Mo ...

Fabricant Chamberlain Catégorie Garage Door Opener

Les documents que nous recevons du fabricant de l'appareilChamberlain 9902 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Chamberlain
- manuels d’utilisations 9902
- fiches produit Chamberlain
- dépliants
- ou étiquettes-énergie Chamberlain 9902
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Chamberlain 9902.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Chamberlain 9902, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Chamberlain 9902. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Chamberlain 9902.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Chamberlain 9902, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Chamberlain 9902 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Chamberlain 9902.

Le manuel d’utilisation complet Chamberlain, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Chamberlain 9902 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Chamberlain 9902, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lChamberlain 9902 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Chamberlain 9902 - qui devraient nous aider dans les premières étapes lors de l'utilisation Chamberlain 9902
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Chamberlain 9902
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Chamberlain 9902 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Chamberlain 9902?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Chamberlain 9902, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chamberlain 9902 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)