Français dropdown-ico

Manuel d’utilisation Lowrance electronic GLOBALMAP 4800M

36 pages 0.58 mb
Télécharger

Aller à la page of 36

Summary
  • Lowrance electronic GLOBALMAP 4800M - page 1

    1 Pub. 988-0151-182 Addendum I LMS-480M, LMS-480DF & GlobalMap 4800M This addendum addresses new items pa cked with your unit, changes to installation procedures, and NMEA 2000 upgrades not documented in the LMS 480M, LMS-480cDF and GlobalMap 4800M manuals. Your unit now packs with a 2-foot (61 cm) blue-to-red adapter cable, 15- foot (4.6 m) ex ...

  • Lowrance electronic GLOBALMAP 4800M - page 2

    2 Power Connections Your unit comes with a power/data cable that splits into three branches, each with several exposed wires. The thicker three-wire cable (white, red and black) is the power supply for your display unit. This cable has no label. The thinner branch with three wires (red, black and shield) is the power cable for a NMEA 2000 network. ...

  • Lowrance electronic GLOBALMAP 4800M - page 3

    3 Powering Your Display Unit The display unit works from a 12-volt DC battery system. Attach the display power cable (with provided 3-amp fuse) to an accessory switch or power bus. If this results in elec trical interference, connect direct to a battery but install an in-line switch on the cable. Caution: We strongly recommend that you shut off the ...

  • Lowrance electronic GLOBALMAP 4800M - page 4

    4 For example, if you have to extend the power cable to the power bus or battery, attach one end of the fuse holder directly to the power bus or battery. This will protect both the unit and the power cable in the event of a short. This unit has reverse polarity protec tion. No damage will occur if the power wires are reversed. However, the unit wil ...

  • Lowrance electronic GLOBALMAP 4800M - page 5

    5 Powering a NMEA 2000 Network Bus A NMEA 2000 bus must be connected to a power source to operate. NMEA 2000 devices, including GPS mo dules, draw their power from the ne two rk bus . If you have a pre-existing NMEA 2000 network instal- lation, it may already be connected to another power source. If you are not sure about a network's power st ...

  • Lowrance electronic GLOBALMAP 4800M - page 6

    6 when not in use. Failure to connect to and use a power switch will drain your boat battery, which could stop your boat's operation. GPS Antenna/Receiver Module Your unit packs with the LGC-3000 GP S module. This device contains the unit's external antenna and rece iver for GPS and WAAS signals. The antenna/receiver module comes with a 1 ...

  • Lowrance electronic GLOBALMAP 4800M - page 7

    7 the telephone wiring in a house. If yo u pick up a phone in your living room, you can hear someone talking into the phone in the bedroom. Lowrance and LEI provide all the cables you will need to create a NMEA 2000 network. Lowrance provides T co nnectors and extension cables so you can add devices along the backbone wherever you want. Once you ha ...

  • Lowrance electronic GLOBALMAP 4800M - page 8

    8 Cable connections for LMS-480M and LMS-480DF. Netw ork socket Pow er/Data socket Display unit pow er cable Sonar socket Transducer NMEA-2000 Pow er cable Speed sensor Data cable LGC-3000 120 ohm terminator 120 ohm terminator Extension cable Double T connector Blue-to-red adapter cable ...

  • Lowrance electronic GLOBALMAP 4800M - page 9

    9 Cable connections for the GlobalMap 4800M. Netw ork socket Pow er/Data socket NMEA-2000 Pow er cable Data cable LGC-3000 120 ohm terminator Double T connector Blue-to-red adapter cable 120 ohm terminator Extension cable Display unit pow er cable ...

  • Lowrance electronic GLOBALMAP 4800M - page 10

    10 NMEA 2000 Device Configuration The NMEA 2000 menu on your display unit's main menu allows you to configure, calibrate and monitor devices on a NMEA 2000 network. The NMEA 2000 menu provides access to the Bus Setup, Fuel Management and NMEA 2000 Alarms. You also can turn on/off Waypoint Sharing and Backlight Synchronization from the NMEA 200 ...

  • Lowrance electronic GLOBALMAP 4800M - page 11

    11 The NMEA Diagnostics page displays information about the perform - ance of the network bus, keeping you updated on bus status, mode, er- rors and bus traffic. The Ethernet Diagnostics page keeps you updated on the performance of an Ethernet connection (if applicable) supplying information ranging from IP Addre ss to upload and download rates (by ...

  • Lowrance electronic GLOBALMAP 4800M - page 12

    12 Tank Select The Tank Select menu allows you to choose from up to three tanks (Port, Center and Starboard), depe nding on the Engine-tank configura- tion that has been selected. This allows you to set up each tank indi- vidually. Tank Size The Tank Size menu allows you to inpu t the size of a selected tank in gallons. After selecting the desired ...

  • Lowrance electronic GLOBALMAP 4800M - page 13

    13 7. Use ↓ ↑ , ← → to input the capacity (gallons) of the tank you chose from the Tank Select menu and press ENT . 8. Repeat Steps 5-7 for each remaining tank. 9. When all tanks have been configured, press the S ET C ONFIGURATION but- ton. The following confirmation message will appear: Are you sure you wish to change the bus configuration ...

  • Lowrance electronic GLOBALMAP 4800M - page 14

    14 The Device Data for an EP-10 Fuel Flow includes F uel Rate (amount of fuel burned per hour), Fuel Used, Trip Fuel Used and Seasonal Fuel Used. NOTE: If, as in the graphic above, you do not have a Suzuki Engine Inter- face, EP-15 Fluid Level or EP-10 Fuel Flow on the network, the Engine & Configuration menu, Tank Select menu, Tank Size dialog ...

  • Lowrance electronic GLOBALMAP 4800M - page 15

    15 A dd Fuel After entering the amount of fuel added to a tank in the Fuel Added dialog, the Add Fuel command finalizes the entry of the data. L ike the Fuel Added dialog, the Add Fuel command will only be used when an amount of fuel is added that does not fill up the tank. Fill Tank You will use the Fill Tank command when calibrating a fuel flow a ...

  • Lowrance electronic GLOBALMAP 4800M - page 16

    16 To Reset Calibration: Choosing the Reset Calibration command will switch fuel flow calibra- tion settings back to factory defaults. 1. Press MENU | MENU , select NMEA 2000 and press ENT . 2. Highlight F UEL M AN AGE M EN T and press ENT . The Fuel Management menu will appear. 3. Highlight to E NGINE S ELECT and press ENT . Select the desired eng ...

  • Lowrance electronic GLOBALMAP 4800M - page 17

    17 The second tab at the top of the NMEA 2000 Alarms page is the Alarm Status Tab. When an alarm has been set for a device, the alarm and its current status will be shown on the Alarm Status window. To view the Alarm Status window, highlight the Alarm Status tab and press ENT . To set NMEA 2000 A larm: 1. Press MENU | MENU , select NMEA 2000 and pr ...

  • Lowrance electronic GLOBALMAP 4800M - page 18

    18 Configuring EP Sensors All configurable devices are configured through their Device Configura- tion menus, which may be accessed th rough the network devices list on the Bus Configuration menu. EP-35 Temperature Configuration To input Devic e Name: 1. Press MENU | MENU , use ↑ ↓ to select NMEA 2000 and press ENT . The NMEA 2000 menu will app ...

  • Lowrance electronic GLOBALMAP 4800M - page 19

    19 Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians. Instance a llows network technicians to re- solve certain electronic probe conflicts. This is most likely to occur if the network includes LMF-200 or LMF-400 digital gauges, which support the display of fewer electronic probes than your GPS or so ...

  • Lowrance electronic GLOBALMAP 4800M - page 20

    20 3. Select the fuel flow you want to rename and press ENT . The Device Configuration menu will appear with the Device Name dialog box high- lighted. 4. Press ENTER and use ↑ ↓ , ← → to input the desired name for the fuel flow. Press ENT . Press EXIT repeatedly to get back to the main display. To select a Location: 1. Press MENU| MENU , us ...

  • Lowrance electronic GLOBALMAP 4800M - page 21

    21 To restore default se ttings: 1. Press MENU| MENU , use ↑ ↓ t o s e l e c t NMEA 2000 and press ENT . The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight B US S ETUP and press ENT , which will open the Bus Configu- ration menu. A list ...

  • Lowrance electronic GLOBALMAP 4800M - page 22

    22 5. Select the desired Tank Instance (location) and press ENT . The fol- lowing confirmation message will appear: Are you sure you wish to change this device's configuration? 6. Highlight Y ES and press ENT . Press EXIT repeatedly to get back to the main display. To select Fluid Ty pe: 1. Press MENU| MENU , use ↑ ↓ to select NMEA 2000 an ...

  • Lowrance electronic GLOBALMAP 4800M - page 23

    23 Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians. Instance a llows network technicians to re- solve certain electronic probe conflicts. This is most likely to occur if the network includes LMF-200 or LMF-400 digital gauges, which support the display of fewer electronic probes than your GPS or so ...

  • Lowrance electronic GLOBALMAP 4800M - page 24

    24 Suzuki Engine Interface Configuration To input Devic e Name: 1. Press MENU| MENU , use ↑ ↓ to select NMEA 2000 and press ENT . The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Man- agement, NMEA 2000 Alarms, Waypoint Sharing and Backlight Syn- chronization. 2. Highlight B US S ETUP and press ENT , which will open the Bus Con ...

  • Lowrance electronic GLOBALMAP 4800M - page 25

    25 5. Select your engine type and press ENT . The following message will appear : Are you sure you wish to change this device's configuration? 6. Highlight Y ES and press ENT . Press EXIT repeatedly to get back to the main display. Advanced Options menu The Engine Interface Advanced Options menu contains three catego- ries: Instance, Restore D ...

  • Lowrance electronic GLOBALMAP 4800M - page 26

    26 NOTE: The Suzuki Engine Interface Devi ce Configuration menu contains two Engine Trim calibration commands, which will be addressed in the next segment of this section, Calibrating EP Sensors. Calibrating EP Sensors The factory calibration settings for the EP-10 Fuel Flow, EP-15 Fluid Level and Suzuki Engine Interface sh ould be adequate for the ...

  • Lowrance electronic GLOBALMAP 4800M - page 27

    27 To calibrate an EP-10 Fuel Flow : 10. If calibration is necessary, press MENU | MENU , select NMEA 2000 and press ENT . 11. Highlight F UEL M AN AGE ME NT and press ENT . 12. Select T ANK L OCATION and press ENT to choose the location of the tank connected to selected fuel flow. Press ENT . 13. Highlight F ILL T AN K and press ENT . The followin ...

  • Lowrance electronic GLOBALMAP 4800M - page 28

    28 3. Select the EP-15 Fluid Level and press ENT . 4. Press ↓ to select C A LIBRATE and press ENT . The Device Calibration menu will appear. Instructions on Calibration will be listed at the top of the menu. 5. Highlight N UM P TS , press ENT and select 2. Press ENT . 6. Select F LUID L EVEL , press ENT , then select E MPTY L EVEL and press ENT . ...

  • Lowrance electronic GLOBALMAP 4800M - page 29

    29 4. Press ↓ to select C A LIBRATE and press ENT . The Device Calibration menu will appear. 5. Highlight N UM P TS , press ENT and select 3 . Press ENT . 6. Make sure your tank is empty, then highlight F LUID L EVEL and press ENT . Select E MPTY LEVEL and press ENT . 7. Select C A LIBRATE and press ENT . The following message will appear: Empty ...

  • Lowrance electronic GLOBALMAP 4800M - page 30

    30 1. Press MENU| MENU , use ↓ ↑ to select NMEA 2000 and press ENT . 2. Highlight B US S ETUP and press ENT , which will open the Bus Configu- ration menu. A list of network devices will be at the top of the page. 3. Select the desired EP -15 Fluid Level and press ENT . 4. Press ↓ to select C A LIBRATE and press ENT . The Device Calibration m ...

  • Lowrance electronic GLOBALMAP 4800M - page 31

    31 1. After selecting Fuel Used as overlay data, fill up your tank and press MENU | MENU . 2. Select NMEA 2000 and press ENT . 3. Highlight F UEL M ANAG EM E NT and press ENT . Select T ANK L OCATION and press ENT . 4. Use ↑ ↓ to select the location (Port, Center or Starboard) of the en- gine interface you want to calibrate and press ENT . 5. H ...

  • Lowrance electronic GLOBALMAP 4800M - page 32

    32 3. Highlight C ALIBRA TE T RI M and press ENT . The Device Calibration win- dow will appear with a list of Calibration Instructions. 4. Highlight S TART C ALIBRATION and press ENT . The following message will appear: Please fully raise the Engine Trim. 5. After engine trim has been fully raised, press ENT . The following message will appear: Ple ...

  • Lowrance electronic GLOBALMAP 4800M - page 33

    33 Reset Calibration highlighted (left) . Reset Calibration confirmation window (right). To Reset Calibration: 1. Press MENU | MENU , select NMEA 2000 and press ENT . 2. Highlight F UEL M AN AGE ME NT and press ENT . 3. Highlight E NGINE S ELECT and press ENT . The Engine Select menu will appear with up to four options: All Engines, Port, Center an ...

  • Lowrance electronic GLOBALMAP 4800M - page 34

    34 Notes ...

  • Lowrance electronic GLOBALMAP 4800M - page 35

    35 Notes ...

  • Lowrance electronic GLOBALMAP 4800M - page 36

    36 Visit our web site: Lowrance Pub. 988-0151-182 © Copyright 2006 All Rights Reserved Printed in USA 122206 Lowrance Electronics, In c. ...

Fabricant Lowrance electronic Catégorie GPS Receiver

Les documents que nous recevons du fabricant de l'appareilLowrance electronic GLOBALMAP 4800M peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Lowrance electronic
- manuels d’utilisations GLOBALMAP 4800M
- fiches produit Lowrance electronic
- dépliants
- ou étiquettes-énergie Lowrance electronic GLOBALMAP 4800M
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Lowrance electronic GLOBALMAP 4800M.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Lowrance electronic GLOBALMAP 4800M, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Lowrance electronic GLOBALMAP 4800M. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Lowrance electronic GLOBALMAP 4800M.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Lowrance electronic GLOBALMAP 4800M, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Lowrance electronic GLOBALMAP 4800M par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Lowrance electronic GLOBALMAP 4800M.

Le manuel d’utilisation complet Lowrance electronic, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Lowrance electronic GLOBALMAP 4800M - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Lowrance electronic GLOBALMAP 4800M, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lLowrance electronic GLOBALMAP 4800M qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Lowrance electronic GLOBALMAP 4800M - qui devraient nous aider dans les premières étapes lors de l'utilisation Lowrance electronic GLOBALMAP 4800M
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Lowrance electronic GLOBALMAP 4800M
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Lowrance electronic GLOBALMAP 4800M dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Lowrance electronic GLOBALMAP 4800M?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Lowrance electronic GLOBALMAP 4800M, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Lowrance electronic GLOBALMAP 4800M il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)