Français dropdown-ico

Manuel d’utilisation Kenwood KRC-366L

32 pages 1.86 mb
Télécharger

Aller à la page of 32

Summary
  • Kenwood KRC-366L - page 1

    KRC-466R KRC-366L ©B64-2445-00/00 (MW/IW/MN) CASSETTE RECEIVER INSTRUCTION MANUAL KRC-466R(M)_U.S r1 02.9.26 2:02 PM Page 1 ...

  • Kenwood KRC-366L - page 2

    — 2 — English Contents Safety precautions ......................3 About Cassette tape ...................4 About RDS ..................................4 General features .........................5 Power Selecting the Source V olume Attenuator Loudness System Q Audio Control Speaker Setting Switching Display TEL Mute Theft Deterrent Faceplate T ...

  • Kenwood KRC-366L - page 3

    — 3 — To prevent injury or fire, take the following precautions: • Insert the unit all the way in until it is fully locked in place. Otherwise it may fall out of place when jolted. • When extending the ignition, battery , or ground wires, make sure to use automotive- grade wires or other wires with a 0.75mm 2 (A WG18) or more to prevent wir ...

  • Kenwood KRC-366L - page 4

    — 4 — English • If you experience problems during installation, consult your Kenwood dealer . • If the unit does not seem to be working right, try pressing the reset button first. If that does not solve the problem, consult your Kenwood dealer . •P ress the reset button if the Disc auto changer fails to operate correctly . Normal operatin ...

  • Kenwood KRC-366L - page 5

    Increasing V olume Press the [ u ] button. Decreasing V olume Press the [ d ] button. V olume Press the [SRC] button. Source required Display T uner "TUNER" T ape "T APE" External disc "DISC"/"CD" Standby (Illumination only mode) "ALL OFF" Selecting the Source Tu rning ON the Power Press the [SRC] b ...

  • Kenwood KRC-366L - page 6

    1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below . 4 Adjust the Audio item Press the [ 4 ] or [ ¢ ] button. Adj ...

  • Kenwood KRC-366L - page 7

    The audio system automatically mutes when a call comes in. When a call comes in "CALL" is displayed. The audio system pauses. Listening to the audio during a call Press the [SRC] button. The "CALL" display disappears and the audio system comes back ON. When the call ends Hang up the phone. The "CALL" display disappears ...

  • Kenwood KRC-366L - page 8

    Function of the KRC-466R T uner features The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate Press the Release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the fac ...

  • Kenwood KRC-366L - page 9

    Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the [#1] — [#6] button. Preset T uning Putting a station with good reception in the memory automatically . 1 Select the band for Auto Memory Entry Press the [FM] or [AM] button. 2 Enter Menu mode Press the [MENU] button for at leas ...

  • Kenwood KRC-366L - page 10

    Setting the volume during T raffic Information. 1 Receive the station. 2 Set the volume you want. 3 Preset the volume Press the [VOL ADJ] button for at least 2 seconds. The volume level display blinks 1 time. Presetting V olume for T raffic Information Switching to traffic information automatically when a traffic bulletin starts even when you aren& ...

  • Kenwood KRC-366L - page 11

    21. Social Affairs "SOCIAL" 22. Religion "RELIGION" 23. Phone In "PHONE IN" 24. T ravel "TRA VEL" 25. Leisure "LEISURE" 26. Jazz Music "JAZZ" 27. Country Music "COUNTRY" 28. National Music "NA TION M" 29. Oldies Music "OLDIES" 30. Folk Music "FOLK M" ...

  • Kenwood KRC-366L - page 12

    Selecting the Program T ype display language. 1 Enter PTY mode Refer to <PTY (Program T ype)> (page 11). 2 Enter Changing Language mode Press the [CLK] button. 3 Select the language Press the [#1] — [#3] button. Button Language [#1] English [#2] French [#3] German 4 Exit Changing Language mode Press the [CLK] button. Changing Language for P ...

  • Kenwood KRC-366L - page 13

    Selecting the station. 1 Select tuner source Press the [SRC] button. Select the "TUNER" display . 2 Select the band Press the [FM] or [AM] button. Each time the [FM] button is pressed it switches between the FM1, FM2, and FM3 bands. 3 T une up or down band Press the [ 4 ] or [ ¢ ] button. During reception of stereo stations the "ST& ...

  • Kenwood KRC-366L - page 14

    Cassette player features Calling up the stations in the memory . 1 Select the band Press the [FM] or [AM] button. 2 Call up the station Press the [#1] — [#6] button. Preset T uning Putting stations with good reception in the memory automatically . 1 Select the band for Auto Memory Entry Press the [FM] or [AM] button. 2 Open Auto Memory Entry Pres ...

  • Kenwood KRC-366L - page 15

    Repeating the present song. Press the [REP] button. Each time the button is pressed the Music Repeat turns ON or OFF . When it's ON, "REP ON" is displayed. Music Repeat Switching to the radio automatically during Fast Forwarding and Rewinding. Press the [T .CALL] button. Each time the button is pressed the T uner Call turns ON or OFF ...

  • Kenwood KRC-366L - page 16

    Fast Forwarding Hold down on the [ ¢ ] button. Release your finger to play the disc at that point. Reversing Hold down on the [ 4 ] button. Release your finger to play the disc at that point. Fast Forwarding and Reversing Playing discs set in the optional accessory disc player connected to this unit. Press the [SRC] button. Select the display for ...

  • Kenwood KRC-366L - page 17

    Play the songs on all the discs in the disc changer in random order . Press the [M.RDM] button. Each time the button is pressed the Magazine Random Play turns ON or OFF . When it's ON, "MRDM ON" is displayed. When the [ ¢ ] button is pressed, the next song select starts. Magazine Random Play (Function of disc changer) Playing all th ...

  • Kenwood KRC-366L - page 18

    Scrolling the displayed CD text or MD title. Press the [SCRL] button. T ext/T itle Scroll Attaching a title to a CD. 1 Play the disc you want to attach a name to A title can't be attached to a MD. 2 Enter Menu mode Press the [MENU] button for at least 1 second. "MENU" is displayed. 3 Select Name set mode Press the [FM] or [AM] button ...

  • Kenwood KRC-366L - page 19

    Setting during operation beep sound etc. functions. The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. 1 Enter Menu mode Press the [MENU] button for at least 1 second. "MENU" is displayed. 2 Select the menu item Press the [FM] or [AM] bu ...

  • Kenwood KRC-366L - page 20

    It takes 3 to 4 minutes to synchronize the clock. Function of the KRC-466R It switches automatically when a news bulletin starts even if the radio isn't being listened to. Also, the time interval when interrupt is prohibited can be set. Display and Setting "NEWS OFF" "NEWS 00M" "NEWS 90M" When "NEWS 00M" ...

  • Kenwood KRC-366L - page 21

    When the news bulletin starts, "NEWS" is displayed, and it switches to the news bulletin. • If you choose the "20M" setting, further news bulletins will not be received for 20 minutes once the first news bulletin is received. • The news bulletin volume is the same level that was set for traffic information (page 10). • Thi ...

  • Kenwood KRC-366L - page 22

    For the setting method refer to the <Disc Naming> (page 18). Disc Naming <In External disc control mode> Setting the displayed text scroll. Display Setting "SCL MANU" Doesn't scroll. "SCL AUTO" Scrolls when the display changes. The text scrolled is shown below . • CD text • MD title T ext Scroll <In Exter ...

  • Kenwood KRC-366L - page 23

    — 23 — — 23 — The use of any accessories except for those provided might result in damage to the unit. Make sure only to use the accessories shipped with the unit, as shown above. ............2 2 ............4 ............4 ............1 3 4 5 ............1 6 1. T o prevent a short circuit, remove the key from the ignition and disconnect th ...

  • Kenwood KRC-366L - page 24

    English — 24 — — 24 — Connecting Wires to T erminals – + + + + + FRONT • L FRONT • R REAR • L REAR • R P.CONT ANT. CONT. 9 Rear right output (Red) 8 Rear left output (White) KENWOOD disc changer input 25 FM/AM antenna input 10 To connect the Disc changer , consult your Disc changer manual. 26 Wiring harness (Accessory 1 ) 13 TEL m ...

  • Kenwood KRC-366L - page 25

    — 25 — — 25 — ■ Connector Function Guide 10 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 Connector A Connector B Pin Numbers Plug Functions for ISO Connectors setting* <External Power Connector> A–4 1 Battery 2 Ignition (ACC) A–5 Power Control A–7 1 Ignition (ACC) 2 Battery A–8 Earth (Ground) Connection <Speaker Connector> B–1 Re ...

  • Kenwood KRC-366L - page 26

    English — 26 — — 26 — Connecting Wires to T erminals ■ Power Control T erminal Connections Power Control terminal (Flat terminal) 4 Power Amplifier 6 The output of the Power Control terminal is switched along with the power on/off switching of the unit. This terminal can be connected to the P .CON (REMOTE) terminal of the amplifier . (MAX ...

  • Kenwood KRC-366L - page 27

    — 27 — — 27 — Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (for example, the sound may skip). Metal mounting strap (commercially available) Self-tapping screw (commercially available) Firewall or metal support Screw (M4X8) (commercially available) ■ Installation 8 mm MAX. ø5mm ø5mm ...

  • Kenwood KRC-366L - page 28

    English — 28 — — 28 — ■ Removing the hard rubber frame 2 When the lower level is removed, remove the upper two locations. The frame can be removed from the top side in the same manner . Catch Lock 1 Engage the catch pins on the removal tool and remove the two locks on the lower level. Lower the frame and pull it forward as shown in the fi ...

  • Kenwood KRC-366L - page 29

    — 29 — What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. General ? The power does not turn ON. 01 ✔ The fuse has blown. ☞ After checking for short circuits in the wires, replace the fuse with one with the ...

  • Kenwood KRC-366L - page 30

    English — 30 — T uner source ? Radio reception is poor . 39 ✔ The car antenna is not extended. ☞ Pull the antenna out all the way . ✔ The antenna control wire is not connected. 40 ☞ Connect the wire correctly , referring to the section on <Connecting Wires to T erminals>. ? It isn't the set T raffic information sound volume. ...

  • Kenwood KRC-366L - page 31

    — 31 — If the following situations, consult your nearest service center: • Even though the disc changer is connected, the Disc Changer source is not ON, with "AUX" showing in the display during the Changer Mode. • Even though no device (KCA-S210A, CA-C1AX, KDC-CPS89 KDC-CPS87, KDC-CX87, KDC-CPS85, KDC-CX85, KDC-CPS82 or KDC-CX82) ...

  • Kenwood KRC-366L - page 32

    English — 32 — Specifications Specifications subject to change without notice. FM tuner section Frequency range (50 kHz space) ...............87.5 MHz –108.0 MHz Usable sensitivity (S/N = 26dB) ................... 8.1 dBf (0.7 µV/75 Ω ) Quieting Sensitivity (S/N = 46dB) .............. 15.2 dBf (1.6 µV/75 Ω ) Frequency response ( ± 3 dB ...

Fabricant Kenwood Catégorie Cassette Player

Les documents que nous recevons du fabricant de l'appareilKenwood KRC-366L peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Kenwood
- manuels d’utilisations KRC-366L
- fiches produit Kenwood
- dépliants
- ou étiquettes-énergie Kenwood KRC-366L
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Kenwood KRC-366L.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Kenwood KRC-366L, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Kenwood KRC-366L. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Kenwood KRC-366L.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Kenwood KRC-366L, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Kenwood KRC-366L par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Kenwood KRC-366L.

Le manuel d’utilisation complet Kenwood, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Kenwood KRC-366L - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Kenwood KRC-366L, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lKenwood KRC-366L qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Kenwood KRC-366L - qui devraient nous aider dans les premières étapes lors de l'utilisation Kenwood KRC-366L
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Kenwood KRC-366L
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Kenwood KRC-366L dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Kenwood KRC-366L?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Kenwood KRC-366L, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Kenwood KRC-366L il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)