Français dropdown-ico

Manuel d’utilisation Exmark LAZER Z HP

24 pages 2.23 mb
Télécharger

Aller à la page of 24

Summary
  • Exmark LAZER Z HP - page 1

    UL TRA V AC ® LAZER Z ® HP MODELS For Serial Nos. 850,000 & Higher Part No. 4500-599 Rev . A ...

  • Exmark LAZER Z HP - page 2

    Exmark reser ves the right to make changes or add improv ements to its products at an y time without incurring any obligation to make such changes to products man ufactured previousl y . Exmark, or its distributors and dealers, accept no responsibility f or v ariations which may be evident in the actual specications of its products and the state ...

  • Exmark LAZER Z HP - page 3

    Introduction CONGRATULATIONS on the purchase of your Exmark Ultra V ac. This product has been carefully designed and man ufactured to gi ve y ou a maxim um amount of dependability and years of trouble-free operation. This man ual contains operating, maintenance , adjustment, and safety instr uctions for y our Exmark Ultra V ac . BEFORE OPERATING Y ...

  • Exmark LAZER Z HP - page 4

    Contents Introduction . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . . 3 Safety .. . . . .. .. . . .. .. . . .. . . . . . . . . . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . . . . . . . . 5 Safety Alert Symbol . . .. . . . . . . . . . .. .. . . .. .. . . .. .. . . .. . . ...

  • Exmark LAZER Z HP - page 5

    Safety Safety Safety Alert Symbol This Safety Alert Symbol (Figure 2) is used both in this man ual and on the mac hine to identify important safety messages which m ust be follow ed to av oid accidents This symbol means: ATTENTION! BECOME ALERT! Y OUR SAFETY IS INV OL VED! Figure 2 1. Safety alert symbol The safety alert symbol appears abov e infor ...

  • Exmark LAZER Z HP - page 6

    Safety collection system or m ulch kit in place and w orking properly . DANGER There are rotating blades in the blo wer and under the mow er deck. Blade contact can cause serious operator or bystander injur y or ev en death. • Do Not reach into blower unless rotation indicator has stopped. Disengage PTO , stop engine, remov e key , w ait for all ...

  • Exmark LAZER Z HP - page 7

    Safety Figure 3 1. Safe Zone-Use the mower here on slopes less than 15 degrees 2. Danger Zone-Use a walk behind mower and/or hand trimmer on slopes greater than 15 degrees, near drop-offs and water . 3. Water • R emov e or mark obstacles suc h as roc ks , tree limbs , etc. from the mowing area. T all grass can hide obstacles . • W atch for ditc ...

  • Exmark LAZER Z HP - page 8

    Safety Safety and Instructional Decals • Keep all safety signs legible . Remov e all grease, dirt and debris from safety signs and instr uctional labels . • R eplace all w orn, damag ed, or missing safety signs . • When replacement components are installed, be sure that current safety signs are afx ed to the replaced components . • If an ...

  • Exmark LAZER Z HP - page 9

    Specications Specications Model Numbers Serial Nos: 850,000 and Higher LHPUV4448; LHPUV4650; LHPUV5256 Systems Bagging System • Collection Bins: – Commercial grade, cloth mesh bags with reinforced bottoms . – Capacity: 8 bushels (2 bags and hood) • Dump Mec hanism: Manual lift off • Blow er T ube: Fixed, abrasion resistant molded po ...

  • Exmark LAZER Z HP - page 10

    Operation Product Overview Figure 4 1. Bag 4. Blower 2. Hood 5. Tube 3. Weight Operation Note: Deter mine the left and right sides of the machine from the nor mal operating position. Pre-Start Make sure y ou understand the controls , their locations , their functions , and their safety requirements . Ensure the blow er , belt cov er , bags , tube a ...

  • Exmark LAZER Z HP - page 11

    Operation 3. T o remov e the bags , shut off dec k dri v e, stop the engine and wait for all moving parts to stop . Open the hood and remov e the bags b y lifting up on the rear of the bag, then unhooking the front clip . Empty bags b y inv erting them. 4. R einstall bags , close and latch the hood before continuing mo wing . Tips for mo wing condi ...

  • Exmark LAZER Z HP - page 12

    Operation CAUTION The deck shea ve will become ver y hot. T ouching a hot deck shea ve can cause sev ere bur ns. Allow the deck shea v e to cool completely before removing the belt. 4. Pull the idler release handle and remov e the belt from the upper groove of the dec k sheav e . 5. Unlatch the front end of the blow er . Pivot the blow er bac k and ...

  • Exmark LAZER Z HP - page 13

    Operation 7. Install the belt co ver using the tw o knobs . Install the discharge tube assembly b y slipping the upper end into the hood, then sliding the lo wer end ov er the blow er discharge opening . Use the latc hes to retain the lo wer end to the blow er . 8. F or Units 600,000 and Higher with T riton Decks: Adjust position of dog leg bafe ...

  • Exmark LAZER Z HP - page 14

    Operation ramp angle . The trailer or tr uc k should be as lev el as possible . Important: Do Not attempt to tur n the unit while on the ramp , y ou may lose control and driv e off the side. A v oid sudden acceleration when driving up a ramp and sudden deceleration when backing do wn a ramp . Both maneuv ers can cause the unit to tip bac kward. 14 ...

  • Exmark LAZER Z HP - page 15

    Maintenance Maintenance Note: Deter mine the left and right sides of the machine from the normal operating position. W ARNING While maintenance or adjustments are being made, someone could star t the engine. Accidental star ting of the engine could seriously injure y ou or other bystanders. Remo ve the k ey from the ignition s witch, engage parking ...

  • Exmark LAZER Z HP - page 16

    Maintenance Lubricate Grease Fittings Note: See char t for ser vice inter v als. 1. Stop engine , w ait for all moving parts to stop , and remov e key . Engag e parking brake . 2. Lubricate ttings with NGLI g rade #2 multi-purpose gun grease. R efer to the following chart for tting locations and lubrication sc hedule. Lubrication Chart Fittin ...

  • Exmark LAZER Z HP - page 17

    Maintenance Cleaning Clean Mufer and Rear Frame Area Service Interval: Before each use or daily Stop engine, wait for all moving parts to stop , and remov e key . Engag e parking brak e. W ARNING Operating engine par ts, especially the mufer, become extremely hot. Severe bur ns can occur on contact and de bris, such as leav es, grass, br ush, ...

  • Exmark LAZER Z HP - page 18

    T roubleshooting T roubleshooting Important: It is essential that all operator safety mechanisms be connected and in proper operating condition prior to mow er use. When a problem occurs , do not ov erlook the simple causes . F or example: starting problems could be caused by an empty fuel tank. The follo wing table lists some of the common causes ...

  • Exmark LAZER Z HP - page 19

    Conditions and Products Co vered Exmark Mfg. Co. Inc. and its aff iliate, Exmark W arranty Company , pursuant to an agreement between them, jointly warrant on the terms and conditions herein, that we will repair , replace or adjust any part on these products and found by us (in the ex ercise of our reasonable discretion) to be defective in factory ...

  • Exmark LAZER Z HP - page 20

    Notes: 20 ...

  • Exmark LAZER Z HP - page 21

    Notes: 21 ...

  • Exmark LAZER Z HP - page 22

    Service Record Date: Description of Work Done: Service Done By: 22 ...

  • Exmark LAZER Z HP - page 23

    G01 1841 Figure 10 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees . Use the slope indicator to determine the degree of slope of hills before operating. Do Not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. ...

  • Exmark LAZER Z HP - page 24

    MID-MOUNT RIDING A CCESSORIES AND OPTIONS SEE EXMARK’S COMPLETE LINE OF A CCESSORIES AND OPTIONS W ALK-BEHIND A CCESSORIES AND OPTIONS GRASS CA TCHER MICRO-MULCH SYSTEM TURF STRIPER ST ANDON CUST OM RIDE SEA T SUSPENSION SYSTEM FULL SUSPENSION SEA T DECK LIFT ASSIST KIT HITCH KIT LIGHT KIT 12 V PO WER POR T MICRO-MULCH SYSTEM OPERA T OR CONTROLLE ...

Fabricant Exmark Catégorie Vacuum Cleaner

Les documents que nous recevons du fabricant de l'appareilExmark LAZER Z HP peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Exmark
- manuels d’utilisations LAZER Z HP
- fiches produit Exmark
- dépliants
- ou étiquettes-énergie Exmark LAZER Z HP
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Exmark LAZER Z HP.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Exmark LAZER Z HP, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Exmark LAZER Z HP. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Exmark LAZER Z HP.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Exmark LAZER Z HP, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Exmark LAZER Z HP par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Exmark LAZER Z HP.

Le manuel d’utilisation complet Exmark, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Exmark LAZER Z HP - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Exmark LAZER Z HP, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lExmark LAZER Z HP qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Exmark LAZER Z HP - qui devraient nous aider dans les premières étapes lors de l'utilisation Exmark LAZER Z HP
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Exmark LAZER Z HP
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Exmark LAZER Z HP dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Exmark LAZER Z HP?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Exmark LAZER Z HP, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Exmark LAZER Z HP il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)