Français dropdown-ico

Manuel d’utilisation Heat & Glo LifeStyle XLR-PB-AU

70 pages 10.54 mb
Télécharger

Aller à la page of 70

Summary
  • Heat & Glo LifeStyle XLR-PB-AU - page 1

    1 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Model: XLR-N-AU XLR-PB-AU • DO NOT store or use gasoli ne or other am- mab le vap ors an d liqu ids in th e v ici nity o f t his or any other appliance. • DO NOT spray aerosols in the vicinity of this appliance while it is in operation. • Whattodoifyou ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 2

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 2 MODELS:XLR-N-AU,XLR-PB-AU ARE SAI GLOBAL APPROVED FOR  NA TUR AL  GAS, PROP ANE OR BUT ANE AS A BALANCEDFLUEHEA TER. Refer to the appliance data plates for gas consumptions and pressures. Inst alla tion of this appli ance should on ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 3

    3 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on replace: _____________________ Dealership purchased from: _______________________________ Dealer Phone: _ ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 4

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 4 Safety AlertKey: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury . • W ARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury . • CAUTION! Indicates a ha ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 5

    5 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12  = Contains updated information. 13Finishing  A. Framing and Finishing Instructions . . . . . . . . . . . . . . . . . 46 B. Mantel and Wall Projections . . . . . . . . . . . . . . . . . . . . . . . 49 C . F a c i n g M a t e r i a l ................................. ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 6

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 6 B. LimitedLifetimeW arranty AUSTRALIANW ARRANTY INFORMA TION W arranty information in the attached manual is for international markets, not Australia. For Australian warranty information, please see below . Hearth&HomeT echnologiesInc(HHT) 75 ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 7

    7 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 W arranty Period Heat & Glo Manufactured Appliances and V enting Components Covered Parts Labor Gas Wood Pellet EP A Wood Coal Electric V enting 5 years 1 years X X Castings & baf es 7 years 3 years X X X Manifold tubs HEA T & GLO chimney and termination 10 years ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 8

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 8 • Non Heat & Glo venting components, hearth components or other accessories used in conjunction with the appliance. • Any part of a pre-existing  replace system in which an insert or a decorative gas appliance is installed. • Removal, installation, reinstallation, s ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 9

    9 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 A. ApplianceCertication NO T IN TEN DE D FO R US E AS  A P RI MAR Y HEA T SOU RC E.  This appliance is tested and approved as either supplemen- tal room heat or as a decorative appliance. It should not be factored as primary heat in residen ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 10

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 10 Figure2.1GeneralOperatingParts B. Y ourFireplace W ARNING! DO NOT operate replace before read - ing and understanding operating instructions. Failure to operate replace according to operating instructions could cause re or injury . If you expect th ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 11

    1 1 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 C. ClearSpace W ARNING! DO NOT place combustible objects in front of the replace or block louvers. High temperatures may start a re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 12

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 12 I. ControlModuleOperation 1. The control module has an ON/OFF/REMOTE selector switch that must be set. See Figure 2.3. OFF Position: Appliance will ignore all power inputs and will not respond to any commands from a wall switch or optional remote. The unit should be in ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 13

    13 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 J. LightingInstructions(IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer . T o prolong battery life, remove them when using the transformer . 1. This appliance is equipped with an ignition device which automati ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 14

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 14 K. AfterFireplaceisLit InitialBreak-inProcedure • The fireplace should be run three to four hours continuously on high. • T urn the replace off and allow it to completely cool. • Remove xed glass assembly . See Section 14.E. • Cl ean xed gl as ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 15

    15 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 GlassCleaning Frequency: Seasonally By: Homeowner T ools Needed : Protective gloves, glass cleaner , drop cloth and a stable work surface. CAUTION! Handle xed glass assembly with care. Glass is breakable. • Avoid striking, scratching or slamming glass • Avoid ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 16

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 16 B. MaintenanceT asks-QualiedService T echnician The following tasks must be performed by a qualied ser- vice technician. GasketSealandGlass AssemblyInspection Frequency: Annually By: Qualied Service T echnician T oolsneeded: Prote ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 17

    17 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 A. T ypical ApplianceSystem NOTICE: Illustrations and photos reect typical installations and are for design purposes only . Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual Figure4.1 T ypicalSystem 4 Get ting ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 18

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 18 B. DesignandInstallationConsiderations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Before ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 19

    19 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 5 F ramingandC learances  A. Selecting ApplianceLocation Whe n sel ect ing a locat ion for the appl ia nce it is impo rt ant to con sid er th e r eq uir ed cle aranc es to wa lls (s ee Figur e 5 .1) . W ARNING! Risk of Fire or Burns! Provide adequate cleara ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 20

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 20 B. Constructingthe ApplianceChase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase. NOTICE: T reatment of ceiling restops and wall shield restops an ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 21

    21 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 D. MantelandW allProjections W ARN IN G! Ri sk of Fi re! C om ply wi th al l mi ni mum cl ear - an ces to c omb us ti ble s as spe ci ed . F ram ing or  nis hi ng ma ter ial c lo ser t ha n th e mi nim ums l is ted m us t b e co nst ru ct - ed ent ire ly of no ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 22

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 22 A. V entT erminationMinimumClearances Figure6.1MinimumHeightFromRoofT oLowestDischarge Opening H (MI N.) - M INIMUM HEIG HT FROM R OOF TO L OWE ST DISC HARGE OP ENING VERTICAL W ALL TERMINA TION CAP HORIZONT AL OVERHANG 12 in. (305 mm) ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 23

    23 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Figure6.3 MinimumClearancesforT ermination NOTES: 1. All distances are measured vertically or horizontally along the wall to a point in line with the nearest part of the terminal. 2. Prohibited area below electricity meter or fuse box extends to ground level. 3. ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 24

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 24 A. ApprovedPipe This appliance is approved for use with Hearth & Home T echnologies SLP venting systems. Refer to Section 17.B for vent component information. DO NOT mix pipe, ttings or joining methods from differ- ent manufacturers. The pipe is tested to be run in ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 25

    25 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Figure7.3 T opV ent-HorizontalT ermination V entingwith1elbow H 1 V 1 VMinimum H 1 Maximum 90 Elbow 1-1/2 ft. (457 mm) 1 ft. (305 mm) 3 ft. (914 mm) 1-1/2 ft. (457 mm) 3-1/2 ft. (1067 mm) 2 ft. (610 mm) 5 ft. (1.52 m) 2.5 ft. (762 mm) 6 ft. (1.85 m ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 26

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 26 INST ALLED HORIZONT ALL Y H 1 H 2 V 1 Figure7.4 1. T opV ent-HorizontalT ermination - (continued) T opV ent-HorizontalT ermination V entingwith2elbows Note : Use SLP Series components only . VMinimum H 1 + H 2 Maximum 90 Elbow 1-1 ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 27

    27 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Figure7.5V erticalV entMaximum Note : If installing a vertical vent/termination of f the top of the appliance, the optional exhaust restrictor may be needed. V 1 V 1 Max=44ft.(13.4m) T opV ent-V erticalT ermination NoElbows Note : Us ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 28

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 28 Figure7.8 H 1 V 1 V 2 T opV ent-V erticalT ermination V entingwith2elbows Note : Use SLP Series components only . V 1 Minimum HMaximum V 2 V 1 +V 2 Minimum 90° Elbow 2 ft. (610 mm) * * 6 in. (152 mm) 3 ft. (914 mm) * * 1-1/2 ft. (457 mm) ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 29

    29 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 IN STALLED HO RI ZON T ALL Y H 1 H 2 V 1 V 2 Figure7.9 T opV ent-V erticalT ermination V entingwith3elbows Note : Use SLP Series components only . V 1 Minimum H 1 + H 2 Maximum V 2 V 1 +V 2 Minimum 90° Elbow 1 ft. (305 mm) * * 1 ft. (305 ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 30

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 30 T opV ent-V erticalT ermination V entingwith4elbows Note : Use SLP Series components only . V 1 Min. H 1 Max. V 2 Min. H 2 Max. V 3 Min. 1-1/2 ft. (457 mm) 4 ft. (1.2 m) 4 ft. (1.2 m) 4 ft. (1.2 m) 3 ft. (1.0 m) V 1 + V 2 + V 3 + H 1 + H 2 Ma ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 31

    31 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). • SLP heat shield - designed to be used on a wall 4-3/8 in. (1 11 mm) to 7-1/2 in. (194 mm) thick. • If wall thickness is less than 4-3/8 in. (1 1 1 mm) the existing heat shields must be field trimmed. If wa ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 32

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 32 C. InstalltheCeilingFirestop A ceiling restop MUST be used between oors and attics. • SLPpipe only - Frame opening 9 in. x 9 i n. (2 2 9 mm x 2 29 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.3). • Frame the area with the same sized ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 33

    33 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 D. Install AtticInsulationShield W ARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home T echnologies Inc. requires the use of an attic shield. Attic shields must meet specied clearance and be se- cured in place. FlatC ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 34

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 34 ELBOW HEA T SHIELD SHOWN IN SHIPPING POSITION CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. A. T opV ent 9 AppliancePreparation  Figure9.1ElbowShield ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 35

    35 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 B. SecuringandLevelingthe Appliance W ARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown- in insulation. ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 36

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 36 1 0 Install ingV entPipe( SLPP ip e )  Figure10.2HighT emperatureSiliconeSealant(149°C(300°F) minimumcontinuousexposure) A. AssembleV entSections T o attach the rst vent component to the starting colla ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 37

    37 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 C. SecureTheV entSections • V er t i ca l r un s o f pi p e mu s t be su pp o rt ed ev er y 8 f t . (2 . 4 4 m ) . • Horizontal sections must be supported every 5 ft. (1.52 m). • V ent supports or plumbers strap (spaced 120º apart) may be used to support. See ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 38

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 38 D.  Di sa ss em bl e V en tS ec ti on s • Rota te either se ction (s ee F igure 10 .7) so the seams on both pipe s ectio ns are alig ned as show n in F igure 10.8. • Pull carefully to separate the pieces of pipe. Figure10.8 AlignandDisassembleV en ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 39

    39 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 F . InstallMetalRoofFlashing • See minimum vent heights for various pitched roofs (Figure 10.1 1) to determine the length of pipe to extend through the roof. • Slide the roof ashing over the pipe sections extending through the roof as shown in Figure 10.12. F ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 40

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 40 SCREWS CAULK STORM COLLAR (1of3) Figure10.15 TERMINA TIONCAP H. InstallV erticalT erminationCap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner ue of the pipe section while placing the outer collar of the ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 41

    41 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 K. InstallHorizontalT erminationCap W ARNING! Risk of Fire! The telescoping ue section of the termination cap MUST be used when connecting vent. • 1-1/2 in. (38 mm) minimum overlap of ue telescoping section is required. Failure to maintain overlap may cause ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 42

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 42 1 1 GasInformation  A. GasPressureRequirements Pressure requirements for XLR-AU replaces are shown in T able 1 1.1 below . T wo taps are provided on the right hand side of the gas control for a test gauge connection to measure the inlet and outlet pressu ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 43

    43 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 CHECK FOR GAS LEAKS Explosion Risk Fire Risk Asphyxiation Risk • Check all ttings and connections. • Do not use open ame. • After the gas line installation is complete, all connections must be tightened and checked for leaks with a commercially-available, non- cor r ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 44

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 44 C. Optional AccessoriesRequirements • This appliance may be used with a wall switch, wall mounted thermostat and/or a remote control. Wiring for optional Hearth & Home T echnologies approved accessories should be done now to avoid reconstruction. Follow instructi ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 45

    45 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 E.JunctionCordInformation The junction cord is installed at the factory . refer to gure 12.2. for more information. D. ElectricalServiceandRepair W ARNING! Risk of Shock! Label all wires prior to dis- connection when servicing controls. Wiring errors ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 46

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 46 1 3 F inishing  A. FramingandFinishingInstructions W ARN IN G! Ri sk o f Fi re ! Co mpl y wi th a ll mi nim um cle ar - an ces to com bus tib les as sp ec i ed. Fr ami ng cl os er tha n th e mi nim ums li ste d mu st be co ns tru ct ed en ti re ly of no ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 47

    47 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 W ARNING! Risk of Fire! Maintainspeciedairspace clearancestocombustibles. Failure to comply with these instructions may cause a re or cause the appliance to overheat. LOWER COVER P ANEL TOP FLANGE FINISHING FLANGES SIDE COLUMNS = NO SCREWS ALLOWED = 1 in ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 48

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 48 Note: The lower cover panel must be pushed all the way down. The outer nishing anges should line up. The replace opening must be between 15-3/4 in. and 16 in. (400 mm and 410 mm) for the decorative fronts to t correctly . See Figure 13.4, Figure 13.5 and Figure 1 ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 49

    49 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 B. MantelandW allProjections W ARN IN G! Ri sk o f Fi re ! Co mpl y wi th a ll mi nim um cle ar - an ces to com bus tib les as sp ec i ed. Fr ami ng cl os er tha n th e mi nim ums li ste d mu st be co ns tru ct ed en ti re ly of no nc om- bu sti ble m ate ria ls ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 50

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 50 C. FacingMaterial • Facing and/or nishing materials must not interfere with air ow through louvers, operation of louvers or doors, or access for service. • Facing and/or nishing materials must never overhang into the glass opening. • Observe all clearances ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 51

    51 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Non-Combustible Finish Material 0 - 4 in. (0 - 102 mm) Thick Bottom Joint 3/4 in (19 mm) 3 in. (76 mm) 3/4 in (19 mm) Figure13.14NoncombustibleSurfaceFinishingMaterial  0-4in.(0-102mm)Thick-InsideFitMethod  (T onicD ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 52

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 52 D. DecorativeFronts W ARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place. Only doors certied for use with this appliance model may be used. Contact your dealer for a list of doors that ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 53

    53 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 A. RemoveFixedGlass Assembly See Section 14.E. B. RemovetheShippingMaterials Remove shipping materials from inside or underneath the rebox. The standard black rock media and manual bag assembly are also shipped underneath the rebox. C. Cleant ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 54

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 54 Figure14.2 AirShutter G. AirShutterSetting Air shutter settings may be adjusted by a qualied install- er at the time of installation. The air shutter is set at the factory for minimum vertical vent run. Adjust air shutter for longer vertical runs. See Fi ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 55

    55 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 A. IntelliFirePlus™IgnitionSystem Symptom PossibleCause Corrective Action 1. Pilot won’t light. The ignitor/module makes noise, but no spark. a. Incorrect wiring. V erify “S” wire (white) for sensor and “I” wire (orange) for ignitor are connected t ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 56

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 56 IntelliFirePlus ™ IgnitionSystem-(continued) Symptom PossibleCause Corrective Action 4. Pilot lights but contin- ues to spark, and main burner will not ignite. (If the pilot continues to spark after the pilot ame has been lit, ame rectication has ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 57

    57 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Frequently AskedQuestions/T roubleshooting Symptom PossibleCause Corrective Action Remote control will not transmit Batteries V erify batteries are functional and installed correctly . Remote control is in Child Lock mode Disengage Child Lock mode. Buttons not being ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 58

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 58 1 6 C o mponentAccess  W ARNING! Risk of Fire, Electric Shock and Burns! T urn off power to module and valve by unplugging the 6V transformer from the junction cord, before removing xed glass assembly . A. D ecor ati veFro ntan dFixe dGl ass As ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 59

    59 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Figure16.5RemoveV alvePlateScrews 3. Set the valve bracket on the front lip of the rebox bot- tom. T urn “off” the ball valve. Disconnect gas valve from the gas ex ball valve assembly at the pressure tting. See Figure 16.6. Figure16.6Remo ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 60

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 60 G. GasV alveReplacement Once the valve assembly has been removed, the gas valve, pilot assembly , orice ex tube, and ex ball valve can be replaced. 1. Place the valve assembly on a clean, stable surface to service or replace any components. 2. Disconnect the o ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 61

    61 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 17 ReferenceMaterials  A. ApplianceDimensionDiagram Di me ns ion s ar e ac tua l ap pl ia nc e dim en si on s. U se fo r re fe re nce o nl y. F or f ram in g di me nsi on s an d cl ea ran ce s re fe r to Se ct io n 5. A B G Q C L D E H O F P N Ø I J K M S ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 62

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 62 B.MaintenanceT asks Inspect MaintenanceT asks Doors 1. Inspect for scratches, dents or other damage and repair as necessary . 2. V erify no obstructions to airow . 3. V erify maintenance of proper clearance to combustible household objects. Gasket Seal, Glass Ass ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 63

    63 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 Cap Shield DRC-RADIUS 14 in. (352 mm) 9-1/2 in. (241 mm) 14 in. (356 mm) COOL-ADD Cap Shield 11-1/2 in. (295 mm) 5-3/4 in. (146 mm) 7 in. (181 mm) 12 in. (308 mm) DVP-BEK2 DVP-HPC Cap Brick Extension 14 in. (352 mm) 5 i n . ( 1 27 m m ) 12 in. (302 mm) Figure17.2V ent? ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 64

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 64 9 in. (222 mm) 6-1/2 in. (165 mm) 6-1/2 in. (168 mm) 6 in. (152 mm) 6-1/2 in. (165 mm) 6-1/2 in. (168 mm) 10-1/4 in. (251 mm) 6-1/2 in. (165 mm) 9-1/4 in. (235 mm) SLP-45-45°Elbow SLP90-90°Elbow Effective Height/ Length SLP-PIPE SLP-HVS HorizontalPipe Sup ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 65

    65 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 SLK-SNKD Snorkel T erminationCap SLP-TVHW V ertical T erminationCap SLP-CCS-BK CathedralCeiling SupportBox-Black SLP-DCF-BK CeilingFirestop Black SLP-WT -BK W allThimble-Black C. V entComponentsDiagrams (continued) SL-2DVP Adapter Figure17 ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 66

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 66 SLP-TRAP Horizontal T ermination Cap 15 in. (384 mm) Note: Heat shields MUST overlap by a minimum of 1-1/2 in. (38 mm). The heat shield is designed to be used on a wall 4 in. (102 mm) to 7-1/4 in. (184 mm) thick. If wall thickness is less than 4 in. (102 mm) the existing heat s ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 67

    67 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 D. ServiceParts XLR-N-AU,XLR-PB-AU LandscapeDV Appliance BeginningManufacturingDate:Nov2009 EndingManufacturingDate:______ IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please pro ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 68

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 68 #14V alve Assembly 13.1 13.2 13.3 13.5 13.6 13.7 13.8 13.9 13.10 13.13 13.1 1 13.4 IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 69

    69 Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 D. ServicePartsList XLR-N-AU,XLR-PB-AU IMPORT ANT : THIS IS DA TED INFORMA TION. When requesting service or replacement parts for your appliance please provide model number and serial number . All parts listed in this manual may be ordered from an authorized deal ...

  • Heat & Glo LifeStyle XLR-PB-AU - page 70

    Heat & Glo • XLR-N-AU, XLR-PB-AU • 2198-906 Rev . M • 5/12 70 Heat & Glo, a brand of Hearth & Home T echnologies Inc. 7571 215th Street West, Lakeville, MN 55044 www .heatnglo.com E. ContactInformation Please contact your Heat & Glo dealer with any questions or concerns. For the location of your nearest Heat & Glo de ...

Fabricant Heat & Glo LifeStyle Catégorie Indoor Fireplace

Les documents que nous recevons du fabricant de l'appareilHeat & Glo LifeStyle XLR-PB-AU peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Heat & Glo LifeStyle
- manuels d’utilisations XLR-PB-AU
- fiches produit Heat & Glo LifeStyle
- dépliants
- ou étiquettes-énergie Heat & Glo LifeStyle XLR-PB-AU
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Heat & Glo LifeStyle XLR-PB-AU.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Heat & Glo LifeStyle XLR-PB-AU, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Heat & Glo LifeStyle XLR-PB-AU. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Heat & Glo LifeStyle XLR-PB-AU.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Heat & Glo LifeStyle XLR-PB-AU, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Heat & Glo LifeStyle XLR-PB-AU par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Heat & Glo LifeStyle XLR-PB-AU.

Le manuel d’utilisation complet Heat & Glo LifeStyle, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Heat & Glo LifeStyle XLR-PB-AU - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Heat & Glo LifeStyle XLR-PB-AU, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lHeat & Glo LifeStyle XLR-PB-AU qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Heat & Glo LifeStyle XLR-PB-AU - qui devraient nous aider dans les premières étapes lors de l'utilisation Heat & Glo LifeStyle XLR-PB-AU
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Heat & Glo LifeStyle XLR-PB-AU
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Heat & Glo LifeStyle XLR-PB-AU dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Heat & Glo LifeStyle XLR-PB-AU?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Heat & Glo LifeStyle XLR-PB-AU, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Heat & Glo LifeStyle XLR-PB-AU il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)