Manuel d’utilisation Pelco IV SE SERIES

16 pages 0.83 mb
Télécharger

Aller à la page of 16

Summary
  • Pelco IV SE SERIES - page 1

    INSTALLATION Spectra ® IV Series Spectra ® IV SE Series C3418M (8/06) Pendant Mount Back Box ...

  • Pelco IV SE SERIES - page 2

    2 C3418M (8/06) Installation 13 2 ...

  • Pelco IV SE SERIES - page 3

    C3418M (8/0 6) 3 1. Install the mount for th e pendant dome . Refer to the inst ructions supplie d with the mount. 2. Open t he hinged do or to the back box. P ush the tab lock towards the wall o f the unit and lift t he door op en. Pull wiring into the back box. Re fer to T able A, T able B, and T able C for wiring dist ances. 3. Screw the back bo ...

  • Pelco IV SE SERIES - page 4

    4 C3418M (8/06) VIDEO UTP+ UTP- RX- RX- TX- TX- PWR- PWR+ GND AUX2 GND GND NO NC COM 7 6 5 4 3 2 1 ALARMS AUX1 5 4 ...

  • Pelco IV SE SERIES - page 5

    C3418M (8/0 6) 5 4. Connect wiring to the circuit board inside the back box. Whe n finished, clos e the door to th e back box and turn o n the power . The green LED will light . NOTES: • Aux 1: Maximum 2 A at low voltage (<40 V) Aux 2: Maximum 30 mA at 32 VDC • If you are u sing both u nshielded twi ste d pair (UTP) wiring and a transla tor ...

  • Pelco IV SE SERIES - page 6

    6 C3418M (8/06) SWITCH 1 AND 2 6 8 7 ...

  • Pelco IV SE SERIES - page 7

    C3418M (8/0 6) 7 6. Configu re DIP switc hes SW1 and SW2 lo cated on th e top of the dome drive. For DIP switch settin gs, refer to the labels locat ed on the top of the dome dr ive or to t he Switch Settings section. NOTE: When co nnecting more than on e Spectra dome to a single controller , terminate th e unit farthest from the controller . T o t ...

  • Pelco IV SE SERIES - page 8

    8 C3418M (8/06) T roubleshooting If your dome do es not power up proper ly after installati on, use the following steps. 1. Check the fuse on the circuit board inside the ba ck box for continuity . Replace the fuse if needed. 2. Check th e wiring with a volt meter to ensure p r oper voltage is being receive d into the back box. If your dome powers ...

  • Pelco IV SE SERIES - page 9

    C3418M (8/0 6) 9 Switch Settings WAR N I NG : If you are using D-ty pe or P-type control, your system may no t operate if the baud rate and address switches are not set cor rectly . The switches ar e set at t he factory at the defau lts for D-t ype control (2400 baud and address 1). T able D. Switch Settings for SW2 Special Sy stems S w i t c h N u ...

  • Pelco IV SE SERIES - page 10

    10 C3418M (8/06) T able E. Switch Settings for SW1, P-T ype Control NOTE: For Coaxitron controls, SW1 is not us ed; set all switches OFF . For D-type con trol systems, refer to T able F . T able F . Switch Settings for SW1, D-T ype Control NOTE: For Coaxitron controls, SW1 is not used; set all switches OFF . For P-type con trol syste ms, refer to T ...

  • Pelco IV SE SERIES - page 11

    C3418M (8/0 6) 11 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 71 ON ON ON O FF OFF OFF ON OFF 72 OFF OFF OFF ON OFF OFF ON OFF 73 ON OFF OFF ON OFF OFF ON OFF 74 OFF ON OFF ON OFF OFF ON OFF 75 ON ON OFF ON OFF OFF ON OFF 76 OFF OFF ON ON OFF OFF ON OFF 77 ON OFF ON ON OFF OFF ON OFF 78 OFF ON ON ON OFF OFF ON OF ...

  • Pelco IV SE SERIES - page 12

    12 C3418M (8/06) SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 151 ON ON ON OFF ON OFF OFF ON 152 OFF OFF OFF ON ON OFF OFF ON 153 ON OFF OFF ON ON OFF OFF ON 154 OFF ON OFF ON ON OFF OFF ON 155 ON ON OFF ON ON OFF OFF ON 156 OFF OFF ON ON ON OFF OFF ON 157 ON OFF ON ON ON OFF OFF ON 158 OFF ON ON ON ON OFF OFF ON ...

  • Pelco IV SE SERIES - page 13

    C3418M (8/0 6) 13 SPECTRA ADDRESS SWITCH SETTI NG SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8 223 ON ON ON ON ON OFF ON ON 224 OFF OFF OFF OFF OFF ON ON ON 225 ON OFF OFF OFF OFF ON ON ON 226 OFF ON OFF OFF OFF ON ON ON 227 ON ON OFF OFF OFF ON ON ON 228 OFF OFF ON OFF OFF ON ON ON 229 ON OFF ON OFF OFF ON ON ON 230 OFF ON ON OFF OFF ON ON ON 2 ...

  • Pelco IV SE SERIES - page 14

    14 C3418M (8/06) Weight (approximate) Back Box Standard Pendan t 2.4 lb (1.09 kg) Environmental Pe ndant 3.5 lb (1.59 kg) Dome Driv e 3.3 lb (1 .48 kg) Lower Dome 0.2 lb (0.09 kg) ELECTRICAL (Dome Drive Only) Input V oltag e 18-32 V AC; 2 4 V AC nominal 22-27 VDC; 24 VDC nominal Input Power 24 V AC 23 V A nominal (ind oor , without heater) 73 VA no ...

  • Pelco IV SE SERIES - page 15

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRA NTY Pelco will r epair or replace, without charge, any merchandise p r oved defect ive in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/F T/FS Series fiber optic pro ducts and TW3000 Series unshielded tw ...

  • Pelco IV SE SERIES - page 16

    W orldwid e Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco. com ISO 9001 Australia | Canada | Finland | France | Italy | Russia | Singapore | Spain | Sweden | The Netherl ands | United Ar ab Emirat es | United Kingdom | ...

Fabricant Pelco Catégorie Security Camera

Les documents que nous recevons du fabricant de l'appareilPelco IV SE SERIES peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Pelco
- manuels d’utilisations IV SE SERIES
- fiches produit Pelco
- dépliants
- ou étiquettes-énergie Pelco IV SE SERIES
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Pelco IV SE SERIES.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Pelco IV SE SERIES, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Pelco IV SE SERIES. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Pelco IV SE SERIES.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Pelco IV SE SERIES, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Pelco IV SE SERIES par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Pelco IV SE SERIES.

Le manuel d’utilisation complet Pelco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Pelco IV SE SERIES - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Pelco IV SE SERIES, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPelco IV SE SERIES qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Pelco IV SE SERIES - qui devraient nous aider dans les premières étapes lors de l'utilisation Pelco IV SE SERIES
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Pelco IV SE SERIES
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Pelco IV SE SERIES dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Pelco IV SE SERIES?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Pelco IV SE SERIES, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pelco IV SE SERIES il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)