Manuel d’utilisation La Crosse Technology WS-7168U

26 pages 0.56 mb
Télécharger

Aller à la page of 26

Summary
  • La Crosse Technology WS-7168U - page 1

    WS-7168U Wireless 433 MHz Radio-controlled Weather Station Instruction Manual ...

  • La Crosse Technology WS-7168U - page 2

    2 TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipm ent 3 About WWVB 3 Quick Set-Up Guide 4 Detailed Set-Up Guide Battery installation 5 Program Mode Program Sequence and Default Settin gs 6 Function Keys 6 Setting the LCD Contrast 7 Setting the Tim e Zone 7-8 Daylight Saving Ti me Sett ing 8 Radio-controlled Ti me Setti ng 9 12 ...

  • La Crosse Technology WS-7168U - page 3

    3 INVENTORY OF CONTENTS 1. The WS-7168U weather station (Figure 1). 2. One TX6U remote tem perature sensor (Figure 2). 3. Mounting hardware 4. Instruction m anual and warranty card. ADDITIONAL EQUIPMENT (not included) 1. Two fresh AA 1.5V batteries for the weather st ation. 2. Two fresh AA 1.5V batteries for the rem ote tem perature sensor. 3. One ...

  • La Crosse Technology WS-7168U - page 4

    4 QUICK SET-UP GUIDE Hint: Use good quality Alkaline Batteri es and avoid rechargeable batteries. 1. Have the indoor weather station and rem ote tem perature sensor 3 to 5 feet apart. 2. Batteries should be out of both units for 10 m inutes. 3. Place the batteries into the remote temperature sensor first then into the indoor weather station . (All ...

  • La Crosse Technology WS-7168U - page 5

    5 DETAILED SET-UP GUIDE BATTERY INSTALLATION A. REMOTE TEMPERATURE SENSOR 1. Remove the m ounting bracket. The bracket snaps on and off easily. 2. Remove the battery cover, by sliding the cover down. 3. Observing the correct polarity install 2 AA batteries. The batteries will fit tightly (to avoid start-up problem s make sure they do not spring fre ...

  • La Crosse Technology WS-7168U - page 6

    6 PROGRAM MODE Programming Note: If 30 seconds is allowed to pass, or the CH button is pressed dur ing the prog ramming mode, the unit will conf irm/set the last information entered—the d isplay will stop flashing an d return to normal time-dat e readings. If you don’t leave the program m ode during the programmi ng of sections IV through XI, y ...

  • La Crosse Technology WS-7168U - page 7

    7 III. SETTING THE LCD CONTRAST 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in the time LCD and the number setting will flash. Note: There are 8 LCD contrast levels t o choose from—“Lcd 0” is the lightest, and “Lcd 7” is the darkest. 3. Press and release the IN button to select the level you desire. 4. Press and ...

  • La Crosse Technology WS-7168U - page 8

    8 TIME ZONES GMT 0 Atlantic -4 EST; Eastern -5 CST; Central -6 MST; Mountain -7 PST; Pacific -8 ALA; Alaska -9 HAW; Hawaii -10 6. Press and release the SET button to confirm and advance to the Daylight Saving Ti me sett ing. V. DAYLIGHT SAVING TIME (DST) SETTING 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in the time LCD ...

  • La Crosse Technology WS-7168U - page 9

    9 VI. RADIO-CONTROLLED TIME ON/OFF SETTING 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in th e time LCD and the number setting w ill flash. 3. Press and release the SET button three times. 4. “RCC” will appear on the rig h t of the time LCD and “ON” o r “OFF” will flash to the left. 5. Press and release the IN ...

  • La Crosse Technology WS-7168U - page 10

    10 6. Press and release the SET button to confirm and advance to the time setting. VIII. TIME SETTING There are two methods by whi ch the tim e and date can be set: A) Automatically via WWVB reception, or B) Manually. A. WWVB (Remote Control Time) This method requires you to do nothing, except wai t for the signal to be received, and to select a ti ...

  • La Crosse Technology WS-7168U - page 11

    11 5. Press and release the IN button to advance the hours. 6. Press and release the OUT button to advance the m inutes. 7. Press and release the SET button to confirm and advance t o the year setting. IX. SETTING THE YEAR, DAY AND MONTH Note: Reception of the WWVB signal will also set the date and day. The reception of the signa l will override an ...

  • La Crosse Technology WS-7168U - page 12

    12 X. SETTING THE SNOOZE Note: This is an unused function of t he indoor weather station and should be disregarded. The setting has no bearing on the operat ion. Please press and release the SET button to adv ance to select the temperature format. XI. SELECTING ° F OR ° C 1. Press and hold the SET button for 5 seconds. 2. “LCD” will show in t ...

  • La Crosse Technology WS-7168U - page 13

    13 XII. SETTING THE FORECAST SENSITIVITY Note: The forecast sensitivity can be adjusted to allow for areas that have a high er or lower sensitiv ity to changing air pressure (for example coastal areas have more pr essure change than areas such as southern Arizona). The numbers correspond to the am ount of air pressure change necessary to trigger a ...

  • La Crosse Technology WS-7168U - page 14

    14 FEATURES OF THE WS-7168U I. WEATHER FORECAST The weather forecasting feature is estim ated to be 75% accurate and is for the next 12 to 24 hours. The weather forecast is based solely upon the change of air pressure over time. The WS-7168U averages past air-pressure readings to provide an accurate for ecast—creating a necessity to disregard all ...

  • La Crosse Technology WS-7168U - page 15

    15 Sunny —indicates that the weather is expected to im prove (not that the weather will be sun n y). Sun with Clouds —indicates that the weather is expected to be fair (not that the weather will be sunny with clouds). Clouds with Rain —indicates that the weather is expected to get worse (not that the weath er will be rainy). These icons indic ...

  • La Crosse Technology WS-7168U - page 16

    16 will display a happy face icon when the temperature is between 68 ° F and 79 ° F (20 ° C and 25.9 ° C), and the humidit y is between 45% and 65%. A sad face icon will be displayed when the te mperature and humidity are outside the mentioned ranges. III. OUTDOOR TEMPERATURE The temperature received from the rem ote temperature sensor is viewe ...

  • La Crosse Technology WS-7168U - page 17

    17 3. While “MAX ” is still displayed press the IN button again to return to the current d ata display. Or you can wait 30 seconds, during either the mini mum or t he maxim um readings, and the unit will au tomatically return to current data readin g s. B. VIEWING THE OUTDOOR TEMPERATURE RECORDS 1. Press the OUT button once. “MIN” appears a ...

  • La Crosse Technology WS-7168U - page 18

    18 V. ADDING REMOTE TEMPERATURE SENSORS (OPTIONAL) The WS-7168U is able to receive signals from 3 different remote temperature sensors. The remote tem perature sensor model(s) that you choose will co me with their own set of instructions—follow these instructions for a complete guide t o setting up. Following are som e brief instructions for th e ...

  • La Crosse Technology WS-7168U - page 19

    19 B. VIEWING AND OPERATING WITH MULTIPLE REMOTE TEMPERATURE SENSOR UNITS 1. To view the temperature of a different remote temperature sensor unit, press and release t he CH button. A shift from one “boxed” number to the next should be observed in the OUTDOOR LCD. 2. To v ie w th e Mi ni mum/M axi mum temperature: first select which remote tem ...

  • La Crosse Technology WS-7168U - page 20

    20 I. THE REMOTE TEMPERATURE SENSOR The remote tem perature sensor can be mounted i n two ways: • with the use of screws, or • using the adhesive tape. A. MOUNTING WITH SCREWS 1) Remove the mounting bracket from the rem ote temperature sensor. 2) Place the mounting bracket over the desired location. 3) Through the three screw holes of the brack ...

  • La Crosse Technology WS-7168U - page 21

    21 A. USING THE TABLE STAND The indoor weather station com es with the t able stand already mounted. If you wish to use the t able-stand all that is required is to place the indoor weather station in an appropriate locati on. B. WALL MOUNTING 1) Remove the table-st and. To do this, pull down on the stand from the rear and rotate forward. 2) Fix a s ...

  • La Crosse Technology WS-7168U - page 22

    22 TROUBLESHOOTING NOTE: For problems not solved, please cont act La Crosse Technology. Problem: No reception of WWVB time signal. Solution: 1) Wait overnight for signal. 2) Be sure indoor weather station is at least 6 feet from any electrical devices, such as televisi ons, computers, or other radio-cont rolled clocks. 3) Remove batteri es for five ...

  • La Crosse Technology WS-7168U - page 23

    23 greater range of the remote te mperature sensor requires a different calibration curve than the indoor range. Error is usual ly greater at the extreme ends of a range, m aking it harder to com pare different ranges with different curves. Under non-laboratory conditions, it i s difficult to compensate for the above factors and obtain an accurate ...

  • La Crosse Technology WS-7168U - page 24

    24 sensor): Outdoor temperature reception (indoor weather station): Every 5 minut es. Transmission range: 80 feet (in open space). Power Supply: Indoor weather station: 2 x AA, IEC LR6, 1.5V. Remote tem perature sensor: 2 x AA, IEC LR3, 1.5V. Battery life cy cle: Approximatel y 12 months. Recomme nded battery type: Alkaline. Dimensions (H x W x D) ...

  • La Crosse Technology WS-7168U - page 25

    25 Technology, Ltd will pay ground return shipping charges to the owner of the product to a USA address only. Your La Crosse Technology, Ltd warranty covers all defects in material and workmanship w ith the follow ing specified exceptions: (1) damage caused by accident, unreasonable use or neglect (including t he lack of reasonable and necessary ma ...

  • La Crosse Technology WS-7168U - page 26

    26 FCC DISCLAIMER THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND 2. THIS DEVICE MUST ACCEPT INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY C AUSE UNDESIRED OPERATION. FCC ID: OMO-01RX (Receiver), OMO-01TX (sensor) Freq. 433.92 M ...

Fabricant La Crosse Technology Catégorie Portable Radio

Les documents que nous recevons du fabricant de l'appareilLa Crosse Technology WS-7168U peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques La Crosse Technology
- manuels d’utilisations WS-7168U
- fiches produit La Crosse Technology
- dépliants
- ou étiquettes-énergie La Crosse Technology WS-7168U
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation La Crosse Technology WS-7168U.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation La Crosse Technology WS-7168U, manuels d’entretien, brefs manuels ou manuels de l’utilisateur La Crosse Technology WS-7168U. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit La Crosse Technology WS-7168U.

Manuel d’utilisation complet de l’appareil La Crosse Technology WS-7168U, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser La Crosse Technology WS-7168U par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs La Crosse Technology WS-7168U.

Le manuel d’utilisation complet La Crosse Technology, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel La Crosse Technology WS-7168U - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières La Crosse Technology WS-7168U, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lLa Crosse Technology WS-7168U qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil La Crosse Technology WS-7168U - qui devraient nous aider dans les premières étapes lors de l'utilisation La Crosse Technology WS-7168U
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de La Crosse Technology WS-7168U
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service La Crosse Technology WS-7168U dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de La Crosse Technology WS-7168U?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec La Crosse Technology WS-7168U, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec La Crosse Technology WS-7168U il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Commentaires (0)