Français dropdown-ico

Manuel d’utilisation Roland RE-20

24 pages 4.17 mb
Télécharger

Aller à la page of 24

Summary
  • Roland RE-20 - page 1

    Thank you, and congratulations on your choice of the BOSS RE-20 Space Echo. Before using this unit, carefully read the sections entitled: “USING THE UNIT SAFELY” and “IMPORTANT NOTES” (separate sheet). These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you ha ...

  • Roland RE-20 - page 2

    2 Contents Main Features .......................... 1 Panel Descriptions .................... 3 Front Panel .......................................... 3 Rear Panel ........................................... 5 Installing Batteries .................... 6 Making the Connections ........... 7 Mono Output Connection ..................... 8 Stereo Outpu ...

  • Roland RE-20 - page 3

    3 Front Panel Panel Descriptions TREBLE Knob Adjusts the echo’s high-frequency range. The frequency response is flat when the knob is at the center position; turning the knob to the right (clockwise) boosts the high frequencies, while turning it to the left cuts the high frequencies. BASS Knob Adjusts the echo’s low-frequency range. The frequen ...

  • Roland RE-20 - page 4

    4 Panel Descriptions POWER Indicator This indicator shows whether the power is on or off, and also functions as a battery-check indicator. * When the indicator starts to dim or fails to light, the batteries are exhausted. When this occurs, install new batteries. For instructions on replacing the batteries, refer to “Installing Batteries” (p. 6) ...

  • Roland RE-20 - page 5

    5 Panel Descriptions Rear Panel INPUT Jacks (INPUT A/MONO, B) These input jacks are used for connecting electric guitars, keyboards, other instruments, and effects processors. Connect mono instruments or effects to the A/MONO jack. “Making the Connections” (p. 7) * The A/MONO jack also doubles as the power switch. The power comes on when a plug ...

  • Roland RE-20 - page 6

    6 Installing Batteries Insert the batteries as shown below, being careful to orient the batteries correctly. fig.010 • When turning the unit upside-down, get a bunch of newspapers or magazines, and place them under the four corners or at both ends to prevent damage to the buttons and controls. Also, you should try to orient the unit so no buttons ...

  • Roland RE-20 - page 7

    7 Making the Connections • When using an AC adaptor, be sure to use only the specified type (PSA series; sold separately). Using an adaptor other than the specified type may cause the unit to malfunction, or cause damage to the unit. • To prevent malfunction and/or damage to speakers or other devices, always turn down the volume and turn off th ...

  • Roland RE-20 - page 8

    8 Making the Connections Mono Output Connection fig.020 fig.030 Electric Guitar AC Adaptor PSA series (sold separately) Guitar Amplifier or or MTR Mixer Keyboard RE-20_e.book 8 ページ ２００７年６月８日　金曜日　午後４時３２分 ...

  • Roland RE-20 - page 9

    9 Making the Connections Stereo Output Connection ■ Mono Input fig.060 ■ Stereo Input fig.070 Electric Guitar AC Adaptor PSA series (sold separately) Guitar Amplifier or or MTR Mixer Keyboard Effector + Electric Guitar AC Adaptor PSA series (sold separately) Guitar Amplifier or MTR Mixer Keyboard or RE-20_e.book 9 ページ ２００７年６? ...

  • Roland RE-20 - page 10

    10 Making the Connections Connecting to SEND/RETURN With Guitar Amps ■ Mono Send/Mono Return fig.060 ■ Mono Send/Stereo Return fig.070 SEND RETURN Electric Guitar AC Adaptor PSA series (sold separately) Guitar Amplifier SEND RETURN R RETURN L Electric Guitar AC Adaptor PSA series (sold separately) Guitar Amplifier RE-20_e.book 10 ページ ２? ...

  • Roland RE-20 - page 11

    11 Making the Connections Connecting to an MTR or Mixer If you want to turn off output of the direct sound—for example when connecting to a mixer’s SEND/RETURN—set the DIRECT switch to OFF. ■ Mono Send/Mono Return fig.060 ■ Stereo Send/Stereo Return fig.070 SEND RETURN Set DIRECT switch to OFF AC Adaptor PSA series (sold separately) MTR M ...

  • Roland RE-20 - page 12

    12 Operating the RE-20 Basic Operation For this demonstration of using the pedals, first press the EFFECT ON/OFF pedal to switch on the effect (ON/OFF indicator lit), and set the DIRECT switch to ON. fig.080 1. Set the knobs as shown in the figure. 2. Using the INPUT VOLUME knob and the volume control on the connected device, adjust the input level ...

  • Roland RE-20 - page 13

    13 Operating the RE-20 Adjusting the Input Volume The input level can be adjusted with the INPUT VOLUME knob . * The input level can be adjusted with the INPUT VOLUME knob regardless of whether the effect is switched on or off. Switching the Echo and Reverb Variations You can use the MODE SELECTOR knob to switch among the twelve Variation modes, wh ...

  • Roland RE-20 - page 14

    14 Operating the RE-20 Setting the Delay Time with the TAP Pedal (Tap Delay Time) 1. Using the MODE SELECTOR knob, select the Variation mode for which the tap delay time is to be set. * For more on the playback heads for which the tap delay time is set, and the maximum values of the settings, refer to “About the Variation Mode” (p. 18). 2. Pres ...

  • Roland RE-20 - page 15

    15 Operating the RE-20 2. Release the TAP pedal. The pitch of the oscillating sound starts to fall, and the original echo sound returns. The TAP indicator lights when the twist effect is finished. * Once the TAP pedal is released, changing the repeat rate or intensity cancels the twist effect. The setting is then changed to the value set with the k ...

  • Roland RE-20 - page 16

    16 Operating the RE-20 Control Using an Expression Pedal You can control the following functions with an expression pedal (Roland EV-5; sold separately) connected to the EXP PEDAL jack on the rear panel. REPEAT RATE: The echo interval becomes shorter as the toe of the expression pedal is pressed further. In Long mode, the range for the Repeat Rate ...

  • Roland RE-20 - page 17

    17 Operating the RE-20 Setting the Function of the Expression Pedal 1. Turn off the RE-20. * Disconnecting the plug from the INPUT A/MONO jack switches off the power. 2. While holding down the TAP pedal, turn on the power to the RE-20. The virtual tape display flashes, and then remains lit. * Connecting the plug to the INPUT A/MONO jack switches on ...

  • Roland RE-20 - page 18

    18 About the Variation Mode You can use the MODE SELECTOR knob to switch among the twelve Variation modes, which offer different combinations of echo and reverb. ● : On : The playback heads set with the tap delay times REPEAT (MODE SELECTOR knob “1”–“4”) : Echo only REVERB ECHO (MODE SELECTOR knob “5”–“11”) : Combined echo and ...

  • Roland RE-20 - page 19

    19 About the Roland SPACE ECHO RE-201 The Roland SPACE ECHO RE-201 is a reverb-equipped tape echo that debuted in 1974. About the Configuration of the Tape Echo/Reverb The tape echo section features an erase head, record head, and three playback heads arranged sequentially at equal intervals, such that a sound is played back three times at equal in ...

  • Roland RE-20 - page 20

    20 Troubleshooting Power doesn’t come on ❍ Is the guitar or keyboard connected correctly to the INPUT A/MONO jack? → Check the connections again (p. 7–p. 11). * The power will not turn on without a plug connected to the INPUT A/MONO jack. ❍ Have the batteries run down? → Replace them with new batteries (p. 6). * The batteries included w ...

  • Roland RE-20 - page 21

    21 Sample Settings ■ AMBIENCE This sound adds a sense of space using a short delay and reverb. ■ RICH ECHO This is a sumptuous sound with a rich reverb added to the delay. This produces an even greater effect when played back in stereo. ■ MULTI SLAP Effective with muting techniques for giving the sound a prominent contour. This is even more e ...

  • Roland RE-20 - page 22

    22 Main Specifications RE-20: Space Echo Nominal Input Level -20 dBu (INPUT VOLUME knob: center), max +4 dBu Input Impedance 1 M Ω Nominal Output Level -20 dBu Output Impedance 1 k Ω Recommended Load Impedance 10 k Ω or greater Display Virtual Tape Display Controls EFFECT ON/OFF pedal TAP pedal BASS knob TREBLE knob REVERB VOLUME knob REPEAT RAT ...

  • Roland RE-20 - page 23

    GR SK CZ SI LV LT EE PL HU FI SE NO DK NL PT ES IT DE FR UK For EU Countries RE-20_e.book 23 ページ ２００７年６月８日　金曜日　午後４時３２分 ...

  • Roland RE-20 - page 24

    G6027121R1 This product complies with the requirements of European Directive 89/336/EEC. For EU Countries For Canada This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canad ...

Fabricant Roland Catégorie Music Mixer

Les documents que nous recevons du fabricant de l'appareilRoland RE-20 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Roland
- manuels d’utilisations RE-20
- fiches produit Roland
- dépliants
- ou étiquettes-énergie Roland RE-20
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Roland RE-20.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Roland RE-20, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Roland RE-20. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Roland RE-20.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Roland RE-20, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Roland RE-20 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Roland RE-20.

Le manuel d’utilisation complet Roland, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Roland RE-20 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Roland RE-20, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lRoland RE-20 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Roland RE-20 - qui devraient nous aider dans les premières étapes lors de l'utilisation Roland RE-20
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Roland RE-20
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Roland RE-20 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Roland RE-20?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Roland RE-20, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Roland RE-20 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)