Français dropdown-ico

Manuel d’utilisation Billy Goat SC120H

46 pages 8.64 mb
Télécharger

Aller à la page of 46

Summary
  • Billy Goat SC120H - page 1

    370310 F11200 3A 1 T HANK Y OU FOR S ELECTING T HE P OWERFUL B ILLY G OA T S OD C UTTER O PERATING AND S AFETY I NSTRUCTIONS M ODEL : SC120H S PECIFICATIONS ENGINE : H.P . 5.5 (4. 1 KW ) ENGINE: TYPE Gasoline, HONDA GX 160 K1 ENGINE: CAPACITY 5.5 hp (4.0 kW ) ENGINE: FUEL CAP. 3.0 qt. (2.84L) ENGINE: OIL CAP. 0.66 qt. (0.6 L) WEIGHT: UNIT 160 .9 # ...

  • Billy Goat SC120H - page 2

    370310 F11200 3A 2 O PE RATING AND S AFETY I NSTR UCTION S SOD CUTTER MODE L-SC12 0 H FOREWORD This machine may only b e utilized for the purpose for w hich it was designed, i.e. agricultural use, for the cutting of shoots, grass and brushwood. Any other use other than that st ated, no t covere d or deduci ble from this Manual and the enclosed Eng ...

  • Billy Goat SC120H - page 3

    370310 F11200 3A 3 Contents of the SOD CUTTER Manual 1. Use of the Manual 2. Notices on the m achine 3. Technical data 4. Lifting and transportation 5. Main parts of the m achine 6. Controls and adjustments 7. A ssembly instructions for the handlebars and end part of the cutting height adjustment lever 8. Safety information a) General instructions ...

  • Billy Goat SC120H - page 4

    370310 F11200 3A 4 2. N OTICES ON THE MACH INE In this Manua l all saf ety information appears in special boxe s headed "W ARNING". WA RNING This heading is used to draw the user's attention t o hazardous areas or m oving parts of the m achine. It is also used in i nstances where failure to comply w ith the instructions given m ay re ...

  • Billy Goat SC120H - page 5

    370310 F11200 3A 5 370302 – Label Controls Instruction, Qty. 1 370300 – Lab el Instructions, Qty . 1 3. T ECHNICAL D ATA FOR THE S OD C UTTER SC120H ...

  • Billy Goat SC120H - page 6

    370310 F11200 3A 6 ENGINE : Gasoline, HONDA GX 160 K1 ENGINE CAPACITY : 5 .5 hp (4.0 kW ) CUTTING W IDTH : 12” (30 cm) CUTTING HEIGHT : adjustable up to 35 mm SPEED GEARS : 1 forwar d gear - 1 re verse gea r TRANSMISSION : mech anical GEARS : in o il ba th START : reco il HEIGHT-ADJUSTABL E HANDL EBARS TIRES : f ront tires = GARDEN 3.00-4 rear ti ...

  • Billy Goat SC120H - page 7

    370310 F11200 3A 7 All material is carefully checked by the manufacturer before shipping. The sod cutter is delivered in a cardb oard box with the hand lebars and end p art of the cutting heigh t adjustment lever disassemble d. Upon receipt of the machine make sure that it has not been dama ged duri ng transit and that the packa ging has not be en ...

  • Billy Goat SC120H - page 8

    370310 F11200 3A 8 5. M AIN PARTS OF THE MACHINE The machine consists of the following main parts A – Blade clutch control lever B – Acce le ra tor con tro l le ver C – Forward clutch control leve r D – Cutt ing he ight adjustment lever E – GX 160 K1 engine F – Cover G – Blade H – Forward -neutral-reverse gear sel ector lever I – ...

  • Billy Goat SC120H - page 9

    370310 F11200 3A 9 6. C ONTROL AND A DJUSTME NTS A) BLA DE CL UTCH CONTR OL LEVER This is used to engag e and disengage the blade movement. Low ering the lever engage s the clutch and releasing it disenga ges the clutch. WA RNING The blade will con tinue to move if the engine is runni ng and the blade clutch is engage d, re gard less of t he positi ...

  • Billy Goat SC120H - page 10

    370310 F11200 3A 10 D) CUTTING HEIGHT A DJUSTMENT LEVER This lever serves to adju st the cutting height according to the typ e of terrain and the thickness of the turf t o be cut. (Fig.2 Ref. A) F) COVER The cover ( Fig. 1, ref . F) prevents any contact with the m oving parts of the machine. Use of the machine wi th out th e said cover is strictly ...

  • Billy Goat SC120H - page 11

    370310 F11200 3A 11 6. A SSEMBLY INSTRUCTIONS FOR THE HANDLEBA RS AND END PART OF THE C UTTING H EIGHT ADJU STMENT LEVER The sod cutter is delivered with the handlebars an d the end part of the cutting heigh t adjustment lever disassembled. Remove the cardboard p ackaging (to be disposed of in an appropri ate manner, in accordance wi th current reg ...

  • Billy Goat SC120H - page 12

    370310 F11200 3A 12 8. S AFET Y INF ORM ATI ON Before using the sod cutter it is essential that the operator has understood the warning s, do's and don'ts and precautionary measures given in this manual and in the engin e manual: the prevention of injury to the operator, third parties, animals or objects directly depends on observa nce of ...

  • Billy Goat SC120H - page 13

    370310 F11200 3A 13 ! S upervise the clothing of personnel operatin g the machine: a lo ng-sleeved jacket wi th close-fitt ing cuff s, long, clo se-f itting trousers, heavy-du ty f ootwear, and a protective cap or helmet should be worn. Avoid weari ng loose-tailed clothing, unbu t toned j ackets or torn, undone or pa rtially zippe d up i tems to pr ...

  • Billy Goat SC120H - page 14

    370310 F11200 3A 14 W ARNI NG. W hen working in a ston y or o bstacle-riddle d area try to remove as many objects as possible be f ore commencing cutting . Then wo rk at a gre ater cut- ting h eight than u sual. WA RNING Stones and oth er objects may be thr ow n outw ards in d irection of the o pera- tor or of other person s in the vicinity . Keep ...

  • Billy Goat SC120H - page 15

    370310 F11200 3A 15 9. T RANSPOR TATION OF THE MAC HINE L OADIN G AND UNLO AD ING FRO M A VEHICLE ! For t ransportatio n it is preferable to use a vehi cle with an open bed. ! Choose firm, f lat groun d. ! Switch off the vehicle 's ignition, pu t into reverse gear, pu ll on the h and brake and block the tires wi th chocks to prevent accidental ...

  • Billy Goat SC120H - page 16

    370310 F11200 3A 16 10. D ESCRIPTION OF THE SAFETY A N D GUARD SY STEMS WA RNING The safety devices must never be tampered with. It is necessary to understand how they work and saf eguard their eff iciency and correct operation. In the instance of doubt, prob- lem s or m alf unction contact your dealer. FORW A RD CONTROL A ND BLA DE MOVEMENT LEVERS ...

  • Billy Goat SC120H - page 17

    370310 F11200 3A 17 12. S TARTING AN D DRIVIN G THE SOD C UTTER The machine can be switched on once all the aforementioned preliminary opera- tions have bee n carried out. Place the feed cock in the OPEN position (direction shown by the arrow) (fig. 4) Bring the choke to the CLOSED position for a cold start (direction shown by the ar- row, Fig. 4a) ...

  • Billy Goat SC120H - page 18

    370310 F11200 3A 18 D RIVING THE MACHINE WA RNING. When using the machine f or the fir st time it is advisable to get the feel of it b y ex ecuting m anoeuvres on flat grou nd free of foreign obj ects. Aft er sw itching on the engine f ollow ing the instructions given in the previou s para- graph: 1. Move the gear lever (fig. 2, ref . C) to the FOR ...

  • Billy Goat SC120H - page 19

    370310 F11200 3A 19 14. C HECKS - Adjust the belt and cable control tension after the fi rst few working hours to compensate i nitial loosen ing. - Briefly opera te all the machine's components to d etect any abnormal n oises or overheatin g. - During the initial running in p eriod avoid heavy -duty usa ge to encourage proper settling of the m ...

  • Billy Goat SC120H - page 20

    370310 F11200 3A 20 C)BELT REPL ACEMENT AND ADJUSTMEN T Switch off the engine and disconnect the spark plug wire before carry ing o ut any maintena nce or repair work on the m achin e. If a belt is w orn or breaks it should be replaced as follows: - remove the m etal guard ( f ig. 6 ref. A), by unscrewing and taking out the screws shown in figure 6 ...

  • Billy Goat SC120H - page 21

    370310 F11200 3A 21 Fig. 6 Fig. 7 ...

  • Billy Goat SC120H - page 22

    370310 F11200 3A 22 Fig. 8 Fig. 9 ...

  • Billy Goat SC120H - page 23

    370310 F11200 3A 23 D) S ERVIC E B RAKE C ONTROL L EVER The service brake (Fig. 9 Ref . A) is connected to the forward control l ever (Fig. 1 Ref. C). W ith the f orward control lever relea sed and the brake engaged ensure that there is play of appro xim ately 2 or 3 mm between the adjustment screw and t he brake cable (Fig. 9 Ref B and C) WA RNING ...

  • Billy Goat SC120H - page 24

    370310 F11200 3A 24 F IG . 10 15. M AINTENANCE AND ST O RAGE ! A ll o perations on the machine must b e carried out exclu sively by authoriz ed personnel. ! A lwa ys switch off the engine whe n checking, adjusting or servicing the ma- chine. ! A llow the machine to cool down before inspection . ! The cover ( Fig. 1 ref. F ) must alway s be correctl ...

  • Billy Goat SC120H - page 25

    370310 F11200 3A 25 ! A fter use s tore the machine in a place w here fuel vapours cann ot reach a na - ked flame or sparks. ! In t he instan ce o f a long period of non-use, drain the fuel tank completely . Use of the machine does not requ ire specific lighting. However, the recommended minimum amount of light (e.g. 200 lux) to be able to read the ...

  • Billy Goat SC120H - page 26

    370310 F11200 3A 26 16. C LEANING THE MACH IN E Proceed in the following ord er: - Switch off the engine an d disconnect the spark plug w ire; - Clean the engin e and the outside of the m achin e with a cloth soaked in a little oil. - Clean all parts of the m achine, particul arly the starting unit, air filter, exhaust and carburetor. It is advisa ...

  • Billy Goat SC120H - page 27

    370310 F11200 3A 27 18. D ECOMM ISSIONIN G AN D SCRAPPING Aft er the working life of the sod cu tter the user must have it dismantled and its components removed as per EEC directives or in accord ance with current leg i sla- tion in f orce in hi s country, taking p articular care over the dismantling of the fol- lowing materials of environ mental i ...

  • Billy Goat SC120H - page 28

    370310 F11200 3A 28 21. T ROUBLESHOOTIN G The follow ing table illust ra tes s ome problems w hic h may arise dur ing oper ation . FAULT CA USE ACTION Belt slips 1. Belt t ens ion inade quat e 2. Too gr eat a wor k ing dept h 3. Belt wo rn 1. Adjus t th e belt t e nsion 2. Reduc e the wor k ing d ept h 3. Re place belt Machine vibr at es ex ce ssiv ...

  • Billy Goat SC120H - page 29

    370310 F11200 3A 29 ENGINE FAULT CAUSE MEASURES TO BE TAKE N Engine s luggis h at swit c h on 1. Acc elerator not in star t-up positio n 2. Ch oke not closed 3. Pet rol does not ar r ive 4. Air bubbles or wat er ins ide the pet r ol lines 5. Thic k oil prev ent s rot at ion 6. W inding or start mecha- nism f ault y 7. Spark plug in poor condi- ti o ...

  • Billy Goat SC120H - page 30

    370310 F11200 3A 30 NOTES ___________ ____________ _____________ ____________ _____________ ____________ ___________ ____________ _____________ ____________ _____________ ____________ ___________ ____________ _____________ ____________ _____________ ____________ ___________ ____________ _____________ ____________ _____________ ____________ ________ ...

  • Billy Goat SC120H - page 31

    370310 F11 200 3A 31 ...

  • Billy Goat SC120H - page 32

    3 2 PARTS LI ST 1/ 6 1 370252 Lever Control (r ighthand ) 1 2 370257 Knob 2 3 370253 Lever Tightener (lefthand) 1 4 370178 Screw M6x55 UNI 5931 2 5 370107 Nut Lock M6 H6 3 6 370255 Lever Hand Accelerator 1 7 370112 W asher Flat M6 1 8 370254 Cable Accel erator 1 9 370148 Nut Lock M6 H8 10 10 370281 Screwcap M10x 20 2 11 370256 Clamp Accelerat or 1 ...

  • Billy Goat SC120H - page 33

    33 PARTS LI ST 1/ 6 CONTI NUED 72 370102 Nut 8 H 6. 5 1 112 370294 Adjuster M6 X 40 1 113 370295 Cable Control Brake 1 114 370296 Bushing Sheath 1 115 370297 Nut M6 H4 1 ...

  • Billy Goat SC120H - page 34

    3 4 ...

  • Billy Goat SC120H - page 35

    35 PARTS LI ST 2/ 6 21 370110 W asher Flat M8 2 23 370259 Fork 03216055 2 24 370260 Clip Fork 1 28 370146 Nut M10 1 30 370147 Screwcap M10x50 P.F. 4 31 370145 W asher wave M10 4 32 370228 Support Handle 2 33 370247 Nut Special for handle support 2 38 370125 Nut Lock M8 2 41 370118 Screwcap M8x25 1 44 370130 Screwcap M8x20 2 48 370112 W asher Flat M ...

  • Billy Goat SC120H - page 36

    36 ...

  • Billy Goat SC120H - page 37

    37 PARTS LI ST 3/ 6 5 370107 Nut Lock M6 H6 1 7 370112 W asher Flat M6 1 25 370136 Nut M8 H5 4 26 370272 Screw S t ud M8x20 UNI 5911 4 27 370224 Arm Control Blade (Righthand) 1 45 370157 Key 8x7x25 1 46 370177 Screw Allen M6 x 25 4 49 370128 Screwcap M6 x 14 1 51 370211 Pulley for s haft with eccentric s 1 52 370150 Nut M12 2 53 370197 Belt Short X ...

  • Billy Goat SC120H - page 38

    38 ...

  • Billy Goat SC120H - page 39

    39 PARTS LI ST 4/ 6 1 370126 Screwcap M8x16 6 2 370110 W asher Flat M8 6 3 370194 Rim Rear wheel 2 4 370277 Tube Inner Rear W heel 2 5 370278 Tire Rear 2 6 370195 Hub wheel 2 7 370158 Pin Elastic 10x40 2 8 370288 Cover Dust 2 9 370289 Felt protection 2 10 370305 Ring Seal 25 X 52 X 7 2 11 370114 Ring Snap Internal 152 2 12 370131 Bearing 25x52x 15 ...

  • Billy Goat SC120H - page 40

    4 0 ...

  • Billy Goat SC120H - page 41

    41 PARTS LI ST 5/ 6 18 370182 Plastic k nob Ø 12 1 19 37016 2 Cap Plastic 1 20 37016 3 W ashe r Fiber 1 21 370159 Scr ew Allen M 8 x 16 4 22 37022 6 Lever Engage- disengage 1 23 370264 Spring G ear Fo rk 6x25 1 24 37016 0 Ball 1 25 37023 3 For k Engage-dis engage 1 26 37016 1 Casin g 1 27 37022 7 For k pivot 1 28 37012 5 Nut Lock M8 1 29 37020 1 G ...

  • Billy Goat SC120H - page 42

    4 2 PARTS LI ST 5/ 6 CONTI NUED 63 370171 O - rin g 108 (8.7 3 x 1. 78) 1 66 370291 Scr ew Stu d M8 UN I 5911 6 67 370241 G a sk et Cove r ( lef t han d) 10 69 37023 0 Cover Lef t 1 70 370169 Pin Cylindr ica l 6x35 1 ...

  • Billy Goat SC120H - page 43

    43 ...

  • Billy Goat SC120H - page 44

    4 4 PARTS LI ST 6/ 6 1 370193 Shim Engine 20x6 2 2 370110 W asher Flat M8 8 3 370234 Support Engine 1 4 370172 Screw T TQST 8x40 4 5 370175 W asher T oroidal M24 4 6 370125 Nut Lock M8 2 7 370126 Screwcap M8x16 2 8 370238 Guide Belt No. 1 1 9 370113 W asher Flat M5 5 10 370106 Screw Allen M5x8 5 11 370237 Guide Belt 1 12 370176 Dowel M8x35 1 13 370 ...

  • Billy Goat SC120H - page 45

    45 PARTS LI ST 6/ 6 CONTI NUED 46 370263 Spring Accelerat or Return 1 47 370107 Nut Lock M6 H6 2 48 370307 Drum W ire Holder 1 49 370297 Nut M6 H4 1 50 370308 Screwcap M 6 X 18 1 ...

  • Billy Goat SC120H - page 46

    370310 F11 200 3A 46 ...

Fabricant Billy Goat Catégorie Brush Cutter

Les documents que nous recevons du fabricant de l'appareilBilly Goat SC120H peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Billy Goat
- manuels d’utilisations SC120H
- fiches produit Billy Goat
- dépliants
- ou étiquettes-énergie Billy Goat SC120H
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Billy Goat SC120H.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Billy Goat SC120H, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Billy Goat SC120H. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Billy Goat SC120H.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Billy Goat SC120H, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Billy Goat SC120H par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Billy Goat SC120H.

Le manuel d’utilisation complet Billy Goat, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Billy Goat SC120H - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Billy Goat SC120H, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lBilly Goat SC120H qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Billy Goat SC120H - qui devraient nous aider dans les premières étapes lors de l'utilisation Billy Goat SC120H
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Billy Goat SC120H
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Billy Goat SC120H dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Billy Goat SC120H?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Billy Goat SC120H, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Billy Goat SC120H il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)