Français dropdown-ico

Manuel d’utilisation CDA HG3602

24 pages Non applicable
Télécharger

Aller à la page of 24

Summary
  • CDA HG3602 - page 1

    Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu GB Domino C ooking Hobs Manual for Inst allation, Use and Maintenanc e HG3601FR - HG3602FR ...

  • CDA HG3602 - page 2

    2 Important This appliance is designed and manufactur ed solely for the cooking of domestic (household) f ood and is not suitable for an y non domestic application and ther ef ore should not be used in a commercial envir onment. The applianc e guar antee will be void if the appliance is used within a non domestic envir onment i.e. a semi commer cia ...

  • CDA HG3602 - page 3

    3 Important Saf eguar ds and R ecommendations – Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will bec ome very hot. Do not touc h hot parts. – After use alw ays ensur e that the contr ol knobs are in the “ ● ” OFF posi ...

  • CDA HG3602 - page 4

    4 Featur es and T ec hnical Data Cooking P oints 1 . T riple ring burner (TR) - 3,50 kW 2. Rapid burner (R) - 3,00 kW 3. Semi-rapid burner (SR) - 1 ,75 kW Contr ol Panel 4. T riple ring burner (1) control knob 5. Rapid burner (2) contr ol knob 6. Semi-rapid burner (3) contr ol knob Not e: – The electric ignition is incorporat ed in the knobs. – ...

  • CDA HG3602 - page 5

    5 How t o Use the Hob Gas Burners Gas flow to the burners is adjust ed by turning the knobs (illustrated in fig.2) whic h contr ol the valves. T urning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: – Symbol ● : T ap closed (burner off) – Symbol : High (maximum) – Symbol : ...

  • CDA HG3602 - page 6

    6 Lighting Gas Burners In order t o light the burner , you must: 1 – Press in the corr esponding knob and turn count er -clockwise (fig. 3) t o the full flame position marked by the symbol and hold the knob in until the flame has been lit. In the case of a mains failure light the burner with a mat ch or lighted t aper . 2 – W ait about ten s ...

  • CDA HG3602 - page 7

    7 Choice o f Burner The symbols printed on the panel by the side of the knob indicate whic h burner you ar e contr olling. Choose a suitable burner depending on the cookwar e diameter and capacity. The pan diameter should be suitable for the burner power to make the most of the burner's high efficiency and not waste fuel. A small pan does not ...

  • CDA HG3602 - page 8

    8 Corr ect use of T riple-Ring Burner The flat-bottomed pans ar e to be placed dir ectly onto the pan-support. T o use the WOK you need to place the pr oper stand in order to av oid any faulty operation of the triple-ring burner (Figs. 5a - 5b). Model: WRONG CORRE CT Fig. 5a Fig. 5b HG3601FR ...

  • CDA HG3602 - page 9

    9 Fig. 6 Fig. 7 ...

  • CDA HG3602 - page 10

    10 Cleaning and Maintenanc e Gener al Tips – Befor e cleaning the hob switc h it off and wait f or it to cool down. – Clean with a cloth, hot water and soap or liquid deter gent. – Do not use products whic h ar e abrasive, c orrosive or c hlorine based. – Do not use steel pads. – Av oid using cleaning products with a c hlorine or acidic b ...

  • CDA HG3602 - page 11

    11 Burners and Grids – These parts can be remov ed and cleaned with appropriat e products. – After cleaning, the burners and their flame spr eaders must be well dried and corr ectly r eplaced. – It is v ery important to c heck that the burner flame spreader and the cap have been corr ectly positioned. Failur e to do so can cause serious pr ...

  • CDA HG3602 - page 12

    12 Corr ect Position o f T riple Ring Burner The triple ring burner must be corr ectly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arr ow . The burner corr ectly positioned must not rot ate (fig. 1 0). Then position the cap A and the ring B (figs. 1 0 - 1 1). The pan support shall be corr ectly posit ...

  • CDA HG3602 - page 13

    13 Corr ect Positioning o f the Semi-r apid and Rapid Burners – It is very important to check that the burner flame spreader F and the cap C have been correctly positioned (see figs. 1 3 and 1 4). They shall be level and must not rot ate. Failur e to do so can cause serious pr oblems. – The pan supports shall be correctly positioned as indica ...

  • CDA HG3602 - page 14

    14 TIPS FOR INS T ALLA TION Location – The appliance may be installed in a kitchen, Kitchen/diner or a bed sitting room, but not in a r oom or space containing a bath or a show er . – The appliance must not be installed in a bed-sit r oom of less than 20m 3 . – The appliance is designed and approv ed for domestic use only and should not be in ...

  • CDA HG3602 - page 15

    15 30 mm Space for connections Clearance Separator Installation T echnical Information f or the Installer In or der to install the hob into the kitc hen fixture, a hole with the dimensions shown in fig. 1 6 has to be made, bearing in mind the following: – Within the unit, between the bottom of the hob and the upper surface of a shelf ther e mus ...

  • CDA HG3602 - page 16

    16 3 cm min 3 cm 4 cm S A R Fast ening the Cookt op Each cooktop is provided with an installation kit including brackets and screws for fastening the cooktop to benc hes fr om 30 to 40 mm thick.The kit includes f our R brac kets and f our self-thr eading scr ews S (figs. 1 9, 20). – Cut the unit accor ding to the dimensions in fig. 1 6. – T u ...

  • CDA HG3602 - page 17

    17 Gas Supply Requir ements Important Not e This appliance is supplied for use on NA TURAL GAS or LPG (check the gas r egulation label attac hed on the appliance). – Appliances supplied for use on NA TURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modification. The appliances ar e manufactur ed fo ...

  • CDA HG3602 - page 18

    18 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified and register ed installer . Installers shall take due account of the pr ovisions of the relev ant British Standar ds Code of Practice, the Gas Safety Regulations and the Building Standar ds (Scotland) (Consolidation) R egula ...

  • CDA HG3602 - page 19

    19 Gas connection Cat: II 2H3+ The fitting (fig. 2 1) is made up of: – 1 nut A – 1 elbow fitting C – gasket F Connection t o the Gas Supply – Be careful when flexible pipes ar e used that they do not come into contact with moving parts. – T o maintain the thickness of 3 cm, the hob is fitt ed with a channel to c ontain the connection ...

  • CDA HG3602 - page 20

    20 J J Con v er sion to Natur al Gas or LPG Replacing the Burner Inject ors If the NA TURAL GAS/LPG conversion kit is not supplied with the appliance this kit can be pur chased by contacting the A fter -Sales Service. Choose the injectors t o be replac ed accor ding to the table below . The injector diameter , expressed in hundredths of a millimetr ...

  • CDA HG3602 - page 21

    21 Regulating the Burner Minimum Set ting When changing from one type of gas to another , the minimum tap output must also be corr ect, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum t o the minimum position. The adjustment is performed with the burner l ...

  • CDA HG3602 - page 22

    22 Mains Electricity Connection Incorr ect installation ma y be danger ous and the manufacturer can no t be held responsible. W arning! This appliance must be earthed The manufacturer declines all responsibility f or any problem caused b y failur e to observ e this rule. THIS APPLIANCE MUST BE C ONNECTED T O THE MAINS SUPPL Y B Y A COMPE TENT PERSO ...

  • CDA HG3602 - page 23

    23 Appliance Servicing CDA pr ovide a quality and effective after -sales service to cover all y our servicing needs. Please attac h your r eceipt to this page f or safekeeping. Please help us to help you by ha ving the following inf ormation available when booking a servic e-call: 1 . Model type, make and model – see the product data plate. 2. Ev ...

  • CDA HG3602 - page 24

    Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www .cda.eu T o contact our Customer Car e Department, or for Servic e, please contact us on the det ails below . Cod. 1104561 - ß 2 ...

Fabricant CDA Catégorie Stove

Les documents que nous recevons du fabricant de l'appareilCDA HG3602 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques CDA
- manuels d’utilisations HG3602
- fiches produit CDA
- dépliants
- ou étiquettes-énergie CDA HG3602
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation CDA HG3602.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation CDA HG3602, manuels d’entretien, brefs manuels ou manuels de l’utilisateur CDA HG3602. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit CDA HG3602.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil CDA HG3602, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser CDA HG3602 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs CDA HG3602.

Le manuel d’utilisation complet CDA, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel CDA HG3602 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières CDA HG3602, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lCDA HG3602 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil CDA HG3602 - qui devraient nous aider dans les premières étapes lors de l'utilisation CDA HG3602
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de CDA HG3602
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service CDA HG3602 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de CDA HG3602?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec CDA HG3602, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec CDA HG3602 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)