Français dropdown-ico

Manuel d’utilisation Pelco VMX300

50 pages 8.37 mb
Télécharger

Aller à la page of 50

Summary
  • Pelco VMX300 - page 1

    ADDENDUM Addendum No. C1563M Date February 19, 2008 Manual Affected VMX300 Video Ma nagement System Installation Manual, C1552M-C Several components on the rear panel of the VM X300/VMX300-E wor kstations have be en moved to new positi ons and the illustrati ons in the VMX300(-E) Installation manual (C1552M-C) a re out-of-dat e. Please refer to the ...

  • Pelco VMX300 - page 2

    2 C1563M (2/08) VMX300(-E) MONITOR OUTPUTS 1. Connect the VGA adapt er to the digital video in terface (DVI) connector on the rear panel. Figure 2. Monitor Port Adapter Connection 2. Use the monito r cables provided with your monitors (not supplied) to connect monitors to the workstatio n as follows: • Dual-monitor systems: Connect the left monit ...

  • Pelco VMX300 - page 3

    C1563M (2/08 ) 3 VMX300(-E) ANAL OG VIDEO INPUTS Y ou can connect one analog video inpu t to -1 model wo rkstations, an d up to four an alog video inpu ts to -4 model workstations. Analog video sources include th e following: • A video source (such as a camera, VCR, or multiplexer) connected directly to the VMX300(- E) workstatio n rear panel • ...

  • Pelco VMX300 - page 4

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .p elco.c om ISO 9001 Australia | Finland | France | G ermany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab Emirate ...

  • Pelco VMX300 - page 5

    C1552M-C (7/07) Installation Manual ...

  • Pelco VMX300 - page 6

    ...

  • Pelco VMX300 - page 7

    C1552M-C (7/07) 3 Contents Important Safe ty Instruct ions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco VMX300 - page 8

    4 C1552M-C (7/07) List of Illustrations 1 Sample VMX300(-E) System wi th Matrix Switchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 2 Pelco ASCII Switchers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

  • Pelco VMX300 - page 9

    C1552M-C (7/07) 5 Important Safety Instructions 1. Read the se instructions. 2. Keep the se instructions. 3. Heed all warn ings. 4. Follow all instructions. 5. Do not use th is apparatus near water . 6. Clean only with dr y cloth. 7. Do not block any ventilatio n openings. Ins tall in accordance with the ma nufacturer’ s instructions. 8. Do not i ...

  • Pelco VMX300 - page 10

    6 C1552M-C (7/07) Regulatory Notices This device co mplies with Part 15 of the FCC Rules. Operation is s ubject to the following two conditions: (1) this device may n ot c ause harmful interference, and (2 ) this device must accept any inte rference received, including interference tha t may cause undesired operat ion. RADIO AND TELEVISION INTERFER ...

  • Pelco VMX300 - page 11

    C1552M-C (7/07) 7 Description The Pelco VMX300(-E) video mana gement system uses a Windows ® -based inte rface to cont rol any combinatio n of analog a nd IP devices in a single integ rated video se curity syste m. With a mouse, y ou can click a ca mera icon on a system map and t hen drag it t o a video dis play window. Mapping conf igurations an ...

  • Pelco VMX300 - page 12

    8 C1552M-C (7/07) MODELS VMX300 and VMX300-E wo rkstations come with soft ware preloaded on a rack mountable PC; keyboard and mouse are includ ed. Each workstation su pports two monit ors. (Note: Mo nitors are not included. A sta ndard VGA or Super VGA monitor can be used.) VMX300 MODELS VMX300 provides control and mo nitoring of CCTV equipment in ...

  • Pelco VMX300 - page 13

    C1552M-C (7/07) 9 VMX300-E MODEL S VMX300-E provid es control and monitoring of CCTV equipment in th e following conf igurations: client-to-se rver; multip le clients- to-server; client-to-multiple servers; or server -to-server . A VMX300-E workstation can be a cl ient/server workstatio n (VMX300-E-CSVR) or a client workstation (VMX300-E-CL). VMX30 ...

  • Pelco VMX300 - page 14

    10 C1552M-C (7/07) VMX300E-B BACKUP SERVER A VMX300-E system can include an optional VMX300E-B-SVR backup server . VMX300E-B-SVR bac kup server workstations include the bac kup server soft ware applicati on and licensing for the backup server and cli ent and up to 10 cameras. Li censes for up to 2,000 camer as can be purchased as needed . NOTE: Whe ...

  • Pelco VMX300 - page 15

    C1552M-C (7/07) 11 T ypical Applications IMPORT ANT NOTE. PLEASE READ. The network imple mentations in this docum ent are shown as ge nera l representa tions only and are not intended to show detailed ne twork topologies. Y our actual network will differ , requiring changes or perhap s additi onal networ k equipment to accommodate the syste ms as i ...

  • Pelco VMX300 - page 16

    12 C1552M-C (7/07) Pelco switchers that include the AS CII protocol in their softwa re communicate directly with the VMX300(-E) workstation, as show n in Figur e 2. The ASCII protoc ol is native to all of the matr ix switchers except for the CM9740 Series and some of the older CM 9760 Series sw itchers. These non-native switchers requi re a hardwar ...

  • Pelco VMX300 - page 17

    C1552M-C (7/07) 13 A controllab le camera that is switched through a switcher can ei ther be control led through the switcher or di rectly from th e VM X300(-E) workstation. If you want to control the ca mera through th e switcher , connect the camera’ s data line to the switcher (r efer to F igur e 4). If you want to control the camera from the ...

  • Pelco VMX300 - page 18

    14 C1552M-C (7/07) Vide o from a camera can b e looped through an other device, as sh own by the solid l ines in Figure 6 . Looping device s include DVRs, distribution amplifiers, and monitors. Figure 6. Looping Camera Outputs DX8000 AND DX9000 SERIES DVRS Figure 7 shows a sample system with DVRs (DX8000, DX9000). Figure 7. Sample VMX300(-E) Sy ste ...

  • Pelco VMX300 - page 19

    C1552M-C (7/07) 15 Y ou can incorporate a DVR in to your system using either of the follo wing methods: • Connect the camera’ s video to th e DVR, and then connect the DVR ’ s looping output to the switcher . Figure 8. Connecting a DVR: Method 1 • Connect the camera’ s video d irectly to the switcher , and then connect the switcher ’ s ...

  • Pelco VMX300 - page 20

    16 C1552M-C (7/07) PELCONET T RANSMISSION SY STEMS In Figure 10 PelcoNets 1 and 2 encode video from Cameras 1 and 2 respectively for tr ansmission over the n etwork. PelcoNet 3 deco des IP video from Cameras 1 and 2 for di splay on the external monito r . PelcoNet 4 decodes video from Cameras 1 and 2 for displa y on the VMX3 00(-E) client. Figure 1 ...

  • Pelco VMX300 - page 21

    C1552M-C (7/07) 17 In Figure 11 PelcoNe ts 1 and 2 encode vide o from Cameras 1 and 2 re spectively for tr ansmission over th e network. PelcoNe t 3 deco des video from the VMX300(-E ) client. The clie nt can also disp lay video from Camer as 3 and 4. Figure 11. Example 2 of a PelcoNet Configuration CAMERA 1 CAMERAS 3 AND 4 VMX SERVER VMX CLIENT MA ...

  • Pelco VMX300 - page 22

    18 C1552M-C (7/07) In Figure 12, P elcoNets 1 and 2 encode video f rom Cameras 1 and 2 respectively for transmissio n ov er the networ k. PelcoNets 3 an d 4 encode video from Cameras 3 and 4 u sing the switchers looping ou tputs. This allows th e video to be displayed on Client 1 an d recorded on the NVR. The NVR also records video from Cameras 1 a ...

  • Pelco VMX300 - page 23

    C1552M-C (7/07) 19 NVR300 NETWORK V IDEO RECORDER Figure 13. Sample VMX300(-E) Sy stem with the NVR300 NET4001A ENCODER NET4001A ENCODER NET350 ENCODER NVR300 NETWORK VMX SERVER VMX CLIENT 2 LEGEND DATA VIDEO VMX CLIENT 1 PELCONET DECODER ...

  • Pelco VMX300 - page 24

    20 C1552M-C (7/07) Installation PARTS LIST USER -SUPPLIED PARTS In addition to the stan dard tools and cables re quired for a video security insta llation, you will need t o provide the following items: • One or two VGA or SVGA mo nitors for each VMX3 00(-E) workstation (the secon d monitor is optional but recommended ). Monitors are not included ...

  • Pelco VMX300 - page 25

    C1552M-C (7/07) 21 Mounting Mount the VMX300(-E) in an EIA-standard 19-inch (48.26 cm) equipment rack, or place it on a flat sur face, such as a shelf or ta ble. Follow these i nstructions to mo unt the VMX300 (-E) in an equi pment rack: 1. Attach the tw o brackets to both sides of the VMX300(-E). 2. Attach the mo unting rails to the equipmen t rac ...

  • Pelco VMX300 - page 26

    22 C1552M-C (7/07) Front V iew Figure 15 illustrates th e components on the fro nt of the VMX300(-E) wo rkstation. The unit do or can be open ed or locked using the supplied keys. Figure 15. VMX300(-E) Front V iew Power LED HDD (Hard Disk Drive ) LED Key Lock (2 Keys Supplied) Fan V entilation Handle (2) Rack Ear (2) Fan Power Button DVD/CD-ROM Dri ...

  • Pelco VMX300 - page 27

    C1552M-C (7/07) 23 Rear V iew In Figure 16 the rear pane l of the VMX300-SYS-4/VMX300 -E-SYS-4 workstation is used to identi fy the components that are common to all models. Monitor outp ut ports an d video input ports are identifie d for each worksta tion model in the VMX300 (-E) Connections sectio n, starting on pa ge 24. Figure 16. VMX300(-E) Re ...

  • Pelco VMX300 - page 28

    24 C1552M-C (7/07) VMX300(-E) Connections The connect or ports on the r ear panel of the VMX300(-E) workst ations allow you t o connect devic es directly to t he workstation, in addition to any system devices connected ove r the network. VMX300(-E) CONNECTI ONS TO THE NETWORK Use the Ethern et port and a standar d unshielded twisted p air Cat5 cabl ...

  • Pelco VMX300 - page 29

    C1552M-C (7/07) 25 VMX300(-E) MONITOR OUTPUTS 1. Connect the VGA adapt er to the digital video in terface (DVI) connector on the rear panel. Figure 19. Monitor Port Adapter Connection 2. Use the monito r cables provided with your monitors (user - supplied) to connect monito rs to the workstation a s follows: • Dual-monitor sy stems: Connect the l ...

  • Pelco VMX300 - page 30

    26 C1552M-C (7/07) VMX300(-E) ANAL OG VIDEO INPUTS Y ou can c onnect one an alog video input to -1 model work stations, and up to four anal og video input s to -4 model wor kstations. Analog video sources include th e following: • A video source (such as a camera, VCR, or multiplexer) co nnected directly to the VMX3 00(-E) workstat ion rear panel ...

  • Pelco VMX300 - page 31

    C1552M-C (7/07) 27 EXTERNAL DEVICES External devices can be connected either with a direct serial conn ection or with an Internet Protocol connection. An ove rview o f each ty pe of connection is provided below; refer to the specific instruct ions provided for each type of external de vice in the followin g pag es. Direct Serial Connectio n A direc ...

  • Pelco VMX300 - page 32

    28 C1552M-C (7/07) Figure 25. VMX300(-E) RS-422 W all Block Connection Internet Protocol An Internet Protocol conne ction means conn ecting the device either di rectly to the VMX300(-E) netw ork or to the s erial port on a networ ked device, such as a PelcoNet en coder . Figure 26. Sample of an Internet Protocol Connection for an External Device VM ...

  • Pelco VMX300 - page 33

    C1552M-C (7/07) 29 KBD300A KEYBOARD 1. Use the RJ-45 straight data cab le that comes with the KBD300A to connect the keyboard to the RJ- 45 wall block, provided in th e KBDKIT . 2. Connect the p ower supply (provided in the KBDKIT) to term inals 3 and 4 on the wa ll bloc k. Polarity is unimportant . 3. Complete the conn ection as described for the ...

  • Pelco VMX300 - page 34

    30 C1552M-C (7/07) Internet Protocol: Complete the following st eps (refer to Figure 28): a. Connect the wall block to an RS-42 2 port on the networked de vice. If the networked de vice does not have an RS-422 port, use a n RS-232 to RS-422 conver ter . b. Connect the IP network to the Ethernet port of the VMX300(-E); refer to IP-Based Devices on p ...

  • Pelco VMX300 - page 35

    C1552M-C (7/07) 31 T able H. Keyboard Address Switch Settings 3. T o se t the keyboar d mode, move swit ches 5, 7, an d 8 to the appr opriate posit ion, as describ ed in T able I. T able I. Keyboard Mode Switch Settings NOTE: Switch 6 enabl es and disables the turbo pa n feature. It ca n be ON or OFF , and it can be switched while the k eyboard is ...

  • Pelco VMX300 - page 36

    32 C1552M-C (7/07) SPECTRA/ESPRIT CONTROL CONNECTIONS If you connected a Spectra or Esprit camera positionin g system di rectly to a vide o input port on the VMX300(-E) workstation (-1 or -4 models only), you must also connect a data cable to th e VMX300(-E) wo rkstation to provide d irect camera control from the VMX 300(-E). 1. Use one of th e COM ...

  • Pelco VMX300 - page 37

    C1552M-C (7/07) 33 CM6700 SWITCHER T o co nnect a CM6700 swit cher directly t o the VMX300(-E), complete the following steps: 1. Using a modifie d null modem cable (user -supplied), plug one end into the DB9 COM 1 port on the VMX300(-E). The mod ified null modem cable should be cut at one en d, so that you can connect th e wires directly to the CM6 ...

  • Pelco VMX300 - page 38

    34 C1552M-C (7/07) CM6800 SWITCHER Y ou can connect a CM6 800 switcher directly to the VMX300(-E), using t he DB9 COM port on the VMX300(-E). Th e recommended CM 6800 port varies, dep ending on t he CM6800 switch er model a nd configur ation. T able J provides a port recommendation for each model or confi guration. T able J. Recommended CM6800 Port ...

  • Pelco VMX300 - page 39

    C1552M-C (7/07) 35 Alternate CM6800 Connection NOTE: This option is recommended only if you choos e not to use t he CM6800-MGR sof tware to progra m the CM6800. 1. Using a null mo dem cable (user-supplied), pl ug one end int o the DB9 COM 1 p ort on the VMX300 (-E). 2. Plug the ot her end of the cable into th e DB9 COM 1 por t on the CM6800 switche ...

  • Pelco VMX300 - page 40

    36 C1552M-C (7/07) CM9700 MATRIX SWITCHING SY STEMS The following connection in structions ap ply to CM9700 matr ix systems that u se CC1 software v ersion 9.xx o r higher and th at use the Pe lco P driver in the VMX300(-E) server configuration (note th at “CM9700”includes th e CM9740, CM9760 , CM9770, and CM9780 mat rix systems ). NOTE: If you ...

  • Pelco VMX300 - page 41

    C1552M-C (7/07) 37 Alternate CM9700 Connection If you contro l your CM9700 sy stem with CM9760-MG R software, you can use the RS- 232 COM port on the CC1 for the VMX300(-E) conn e ction. Complete the following step s to connect the VMX300(- E) to the CC1: 1. Using a null mo dem cable (user-supplied), pl ug one end into one of the RS- 232 ports (COM ...

  • Pelco VMX300 - page 42

    38 C1552M-C (7/07) CM9760-ALM ALARM INTERFACE UNIT T o connect a CM9760-ALM alarm interface unit to the VMX300(-E), complete th e following steps (refer to the CM9760-ALM Installat ion/Operation manual for detailed instructions): 1. Set DIP swit ch SW1 on the CM97 60-ALM to us e RS-232 communi cation on por t 0. 2. Connect the al arm unit to th e V ...

  • Pelco VMX300 - page 43

    C1552M-C (7/07) 39 CM9760-REL RELAY INTERFACE UNIT T o co nnect a CM9760 -REL relay interf ace unit to t he VMX300(-E), co mplete the followi ng steps (refer to the CM9760-RE L Installat ion/Operation manual for detailed instructions): 1. Connect the re lay unit to the VMX300(-E) as de scribed below for the appropriat e communicatio n mode: Direct ...

  • Pelco VMX300 - page 44

    40 C1552M-C (7/07) SERIAL OUTPUT DEVICE Connect a s erial outpu t device to the VMX300(-E) usi ng either a direct seria l connection or an Interne t Protocol c onnection. Re fer to Figure 24 on page 27 for a sample dire ct serial connection or to Figure 26 on pa ge 28 for a sample Internet Protoc ol connection. After installing system ha rdware, co ...

  • Pelco VMX300 - page 45

    C1552M-C (7/07) 41 POWER CABLES 1. Connect the VM X300(-E) workstation power cor d to the workstation power input and then to an UP S. NOTE: When connectin g the workstation to a 230 V AC or higher powe r source, the use of an U PS, such as model PW9120 700i (manufactured by Powe rware) or equivalent, is required to comp ly with CE-marking requirem ...

  • Pelco VMX300 - page 46

    42 C1552M-C (7/07) Appendix CHANGING THE PORT SETTINGS OF A VMX300(-E) COM PORT 1. On the Windows XP desktop, right-click the M y Computer icon, and then click Properties. The System Pr operties dialog box a ppe ars. 2. Click the Hardware tab, and then click Device Manager . The Device Manager window opens. 3. Click the + symbol next to Ports. Th e ...

  • Pelco VMX300 - page 47

    C1552M-C (7/07) 43 Specifications ELECTRICAL / VIDEO Input Voltage 100-240 VAC, 50/60 Hz, autoran ging Signal System NTSC/P AL Vide o Outputs 2 SVGA Power Consumptio n 75 W MECHANICAL Connectors USB 4 SVGA Monitor Port 15-pin D-type Printer Po rt 25-pin D-t ype COM 1 and 2 RS-232, 9-pin D- type COM 3 and 4 RS-422, 9-pin D-typ e Modem 2 RJ-11 ports ...

  • Pelco VMX300 - page 48

    ...

  • Pelco VMX300 - page 49

    PRODUCT WARRANTY AND RETURN INFORMA TION WARRANTY Pelco will repair or replace, without char ge, any merchandise proved defective in material or workmanship for a period of one year after the date of sh ipment. Exceptions to this warranty a re as noted below: • Five years on fi ber optic product s and TW3000 Series un shielded twisted pair transm ...

  • Pelco VMX300 - page 50

    W orldwide Headquarters 3500 Pelco W ay Clovis, California 93612 USA USA & Canada T el: 800/289-9100 Fax: 800/289-9150 International T el: 1-559/292-1981 Fax: 1-559/348-1120 www .pelco.c om ISO 9001 Australia | Canada | Finland | France | Germany | Italy | Macau | The Netherlands | Russia | Singapore South Africa | Spain | Sweden | United Arab ...

Fabricant Pelco Catégorie Home Theater Server

Les documents que nous recevons du fabricant de l'appareilPelco VMX300 peuvent être divisés en plusieurs groupes. Ceux-ci sont, entre autres:
- dessins techniques Pelco
- manuels d’utilisations VMX300
- fiches produit Pelco
- dépliants
- ou étiquettes-énergie Pelco VMX300
Tous sont importants, mais les informations les plus importantes du point de vue de l'utilisation de l'appareil se trouvent dans le manuel d’utilisation Pelco VMX300.

Un groupe de documents appelé manuels d’utilisation est également divisé en types plus spécifiques, tels que: Manuels d’installation Pelco VMX300, manuels d’entretien, brefs manuels ou manuels de l’utilisateur Pelco VMX300. Selon vos besoins, vous devriez chercher le document dont vous avez besoin. Sur notre site, vous pouvez voir le manuel le plus populaire d’utilisation du produit Pelco VMX300.

Manuels d’utilsiation similaires

Manuel d’utilisation complet de l’appareil Pelco VMX300, quelle devrait-elle être?
Le manuel d’utilisation, également appelé le mode d’emploi, ou tout simplement le manuel, est un document technique destiné à aider à utiliser Pelco VMX300 par les utilisateurs. Des manuels sont généralement écrits par un rédacteur technique, mais dans un langage accessible à tous les utilisateurs Pelco VMX300.

Le manuel d’utilisation complet Pelco, devrait inclure plusieurs éléments de base. Certains d'entre eux sont moins importants, tels que: la couverture / page de titre ou pages d'auteur. Cependant, la partie restante, devrait nous fournir des informations importantes du point de vue de l'utilisateur.

1. Introduction et des conseils sur la façon d'utiliser le manuel Pelco VMX300 - Au début de chaque manuel, nous devrions trouver des indices sur la façon d'utiliser le document. Il doit contenir des informations sur l'emplacement de la table des matières Pelco VMX300, FAQ ou des problèmes les plus fréquents - les points qui sont les plus souvent recherchés par les utilisateurs de chaque manuel
2. Table des matières - index de tous les conseils pour lPelco VMX300 qui peuvent être trouvés dans le document courant
3. Conseils sur la façon d'utiliser les fonctions de base de l’appareil Pelco VMX300 - qui devraient nous aider dans les premières étapes lors de l'utilisation Pelco VMX300
4. Troubleshooting - séquence systématique des activités qui nous aideront à diagnostiquer et ensuite résoudre les principaux problèmes de Pelco VMX300
5. FAQ - questions fréquemment posées
6. Détails du contact Informations sur l'endroit où chercher le contact avec le fabricant / service Pelco VMX300 dans un pays donné, si le problème ne peut être résolu par nous-mêmes.

Avez-vous une question à propos de Pelco VMX300?

Utiliser le formulaire ci-dessous

Si vous n’avez pas résolu votre problème avec Pelco VMX300, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Pelco VMX300 il est probable qu’il a envie de partager la façon de le résoudre.

Réécrire le texte de l'image

Captcha
Nouvelle image

Commentaires (0)