-
Chamberlain 3255 1/2 HP - page 1
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1 196 www .liftmaster .com GARAGE DOOR OPENER Models 3245 1/3 HP 3255 1/2 HP 3255-2 1/2 HP For Residential Use Only Owner’s Manual ■ Please read this manual and the enclosed safety materials carefully! ■ Fasten the manual near the garage door after installation. ■ The doo ...
-
Chamberlain 3255 1/2 HP - page 2
2 Introduction 2-5 Safety symbol and signal word review ........................2 Preparing your garage door ........................................3 T ools needed ...............................................................3 Planning .....................................................................4 Carton inventory ....................... ...
-
Chamberlain 3255 1/2 HP - page 3
3 T o prevent damage to garage door and opener: • AL WA YS disable locks BEFORE installing and operating the opener . • ONL Y operate garage door opener at 120V , 60 Hz to avoid malfunction and damage. T o prevent possible SERIOUS INJURY OR DEA TH: • AL WA YS call a trained door systems technician if garage door binds, sticks, or is out of ba ...
-
Chamberlain 3255 1/2 HP - page 4
materials may be required. Y ou may find it helpful to refer back to this page and the accompanying illustrations as you proceed with the installation of your opener . FI N ISHED CEILI N G S u pport b racket & fastening hard w are is re qu ired. See page 12. Slack in chain tension is normal w hen garage door is closed. Safety Re v ersing Sensor ...
-
Chamberlain 3255 1/2 HP - page 5
5 Y our garage door opener is packaged in two cartons which contain the motor unit and all parts illustrated below . Accessories will depend on the model purchased. If anything is missing, carefully check the packing material. Parts may be stuck in the foam. Hardware for installation is also listed below . Carton Inventor y Straight Door Arm Sectio ...
-
Chamberlain 3255 1/2 HP - page 6
6 ASSEMBL Y STEP 1 Attach the Rail to the Motor Unit T o avoid installation difficulties, do not run the garage door opener until instructed to do so. • Remove the two washered bolts mounted in top of motor unit. • Position rail at a 45˚ angle to opener so one hole in rail and motor unit line up. • Thread one of the washered bolts part way i ...
-
Chamberlain 3255 1/2 HP - page 7
7 Lock W asher T o Tighten O u ter Nu t Inner Nu t T rolley Chain Base of Rail 1/2" (13 mm) T o Tighten Inner Nu t O u ter Nu t Mid Length of Rail INST ALLA TION ASSEMBL Y STEP 3 Tighten the Chain • Spin the inner nut and lock washer down the trolley threaded shaft, away from the trolley . • T o tighten the chain, turn outer nut in the dir ...
-
Chamberlain 3255 1/2 HP - page 8
8 INST ALLA TION STEP 1 Determine the Header Bracket Location Installation procedures vary according to garage door types. Follow the instructions which apply to your door . 1. Close the door and mark the inside vertical centerline of the garage door . 2. Extend the line onto the header wall above the door . Y ou can fasten the header bracket withi ...
-
Chamberlain 3255 1/2 HP - page 9
9 INST ALLA TION STEP 2 Install the Header Bracket Y ou can attach the header bracket either to the wall above the garage door , or to the ceiling. Follow the instructions which will work best for your particular requirements. Do not install the header bracket over drywall. If installing into masonry , use concrete anchors (not provided). W ALL HEA ...
-
Chamberlain 3255 1/2 HP - page 10
10 Cle v is Pin 5/16"x2-3/4" Ring Fastener INST ALLA TION STEP 3 Attach the Rail to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a protective base. NOTE: If the door spring is in the way you’ll need help. Have someone hold the opener securely on a temporary support to a ...
-
Chamberlain 3255 1/2 HP - page 11
11 ONE-PIECE DOOR WITHOUT TRACK A 2x4 on its side is convenient for setting an ideal door-to-rail distance. • Remove foam packaging. • Raise the opener onto a stepladder . Y ou will need help at this point if the ladder is not tall enough. • Open the door all the way and place a 2x4 on its side on the top section of the door beneath the rail. ...
-
Chamberlain 3255 1/2 HP - page 12
Meas u re Distance Lag Scre w s 5/16"-18x1-7/8" Str u ct u ral S u pports Bracket (Not Pro v ided) Lag Scre w s 5/16"-18x1-7/8" (Not Pro v ided) Bolt 5/16"-18x7/8" Lock W asher 5/16" N u t 5/16"-18 FINISHED CEILING Hidden S u pport Bolt 5/16"-18x7/8" Lock W asher 5/16" N u t 5/16"-18 Bolt ...
-
Chamberlain 3255 1/2 HP - page 13
T o release wire, push in tab with screwdriver tip Door Control Connections 7/16" (11 mm) Strip wire 7/16" (1 1 mm) Red Grey White L O C K L IG H T Slot Figure 4 REMOVE COVER INST ALLA TION STEP 6 Install the Door Control Locate door control w ithin sight of the door at a minim u m height of 5 feet (1.5 m) w here small children cannot rea ...
-
Chamberlain 3255 1/2 HP - page 14
14 INST ALLA TION STEP 7 Install the Light • Press the release tabs on both sides of lens. Gently rotate lens back and downward until the lens hinge is in the fully open position. Do not remove the lens. • Install up to a 100 watt maximum light bulb in each socket. The light will turn O N and remain lit for approximately 4-1/2 minutes when powe ...
-
Chamberlain 3255 1/2 HP - page 15
15 INST ALLA TION STEP 9 Electrical Requirements T o avoid installation difficulties, do not run the opener at this time. T o reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This plug will only fit into a grounding type outlet. If the plug doesn’t fit into the outlet you have, conta ...
-
Chamberlain 3255 1/2 HP - page 16
16 In v isi b le Light Beam Protection Area Sensor Beam 6" (15 cm) max. a b o v e floor Sensor Beam 6" (15 cm) max. a b o v e floor Facing the door from inside the garage INST ALLA TION STEP 10 Install The Protector System ® The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the ...
-
Chamberlain 3255 1/2 HP - page 17
17 DOOR TRACK MOUNT (RIGHT SIDE) Indicator Light Lens Lip Sensor Bracket Door T rack FLOOR MOUNT (RIGHT SIDE) W ALL MOUNT (RIGHT SIDE) Indicator Light Sensor Bracket Lens Extension Bracket (See Accessories) Inside G arage W al l (Pro v ided w ith Extension Bracket) (Pro v ided w ith Extension Bracket) Fi g ure 1 Fi g ure 2 Fi g ure 3 Fi g ure 4 W A ...
-
Chamberlain 3255 1/2 HP - page 18
Invisible Light Beam Protection Area Safety Reversing Sensor Safety Reversing Sensor Connect Wire to Opener Quick-Connect T erminals Bell Wire Bell Wire Finished Ceiling Quick-Connect T erminals 3. Insert into appropriate terminals 1. Strip wire 7/16" (1 1 mm) 2. T wist like colored wires together Red Grey White 7/16" (1 1 mm) 18 Carriage ...
-
Chamberlain 3255 1/2 HP - page 19
19 Fiberglass, aluminum or lightweight steel garage doors WILL REQUIRE reinforcement BEFORE installation of door bracket. Contact your door manufacturer for reinforcement kit. WARN ING CAUTION WARN ING WARN ING INST ALLA TION STEP 11 Fasten the Door Bracket Follow instructions which apply to your door type as illustrated below or on the following p ...
-
Chamberlain 3255 1/2 HP - page 20
20 Header W all V ertical Centerline of Garage Door Finished Ceilin g Optional Placement of Door Bracket Header Bracket Door Bracket 2x4 S u pport For a door w ith no exposed framing, or for the optional installation, u se lag scre w s 5/16"x1-1/2" (Not Pro v ided) to fasten door b racket. MET AL DOOR T op of Door (Inside Garage) Door Bra ...
-
Chamberlain 3255 1/2 HP - page 21
21 INST ALLA TION STEP 12 Connect Door Arm to T rolley Follow instructions which apply to your door type as illustrated below and on the following page. SECTIONAL DOORS ONL Y • Make sure garage door is fully closed. Pull the emergency release handle to disconnect the outer trolley from the inner trolley . Slide the outer trolley back (away from t ...
-
Chamberlain 3255 1/2 HP - page 22
22 ALL ONE-PIECE DOORS 1. Assemble the door arm, Figure 4: • Fasten the straight and curved door arm sections together to the longest possible length (with a 2 or 3 hole overlap). • W ith the door closed, connect the straight door arm section to the door bracket with the 5/16"x1-1/4" clevis pin. • Secure with a ring fastener . 2. Ad ...
-
Chamberlain 3255 1/2 HP - page 23
23 ADJUSTMENT STEP 1 Adjust the UP and DOWN T ravel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. T o operate the opener , press the Door Control push bar . Run the opener through a complete travel cycle. • Does the door open and close completely? • Does the door stay closed and not rev ...
-
Chamberlain 3255 1/2 HP - page 24
ADJUSTMENT STEP 2 Adjust the Force Force adjustment controls are located on the back panel of the motor unit. Force adjustment settings regulate the amount of power required to open and close the door . If the forces are set too light, door travel may be interrupted by nuisance reversals in the down direction and stops in the up direction. W eather ...
-
Chamberlain 3255 1/2 HP - page 25
Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSL Y INJURED or KILLED by a closing garage door . • Safety reversal system MUST be tested ever y month. • If one control (force or travel limits) is adjusted, the other control may also need adjustment. • After ANY adjustments are made, t ...
-
Chamberlain 3255 1/2 HP - page 26
OPERA TION 26 IMPORT ANT SAFETY INSTRUCTIONS T o reduce the risk of SEVERE INJUR Y or DEA TH: Using Y our Garage Door Opener Y our Security ✚ ® opener and hand-held remote control have been factory-set to a matching code which changes with each use, randomly accessing over 100 billion new codes. Y our opener will operate with up to eight Securit ...
-
Chamberlain 3255 1/2 HP - page 27
T o Open the Door Manually The door should be fully closed if possible. Pull down on the emergency release handle and lift the door manually . T o reconnect the door to the opener , press the door control push bar . The lockout feature prevents the trolley from reconnecting automatically . Pull the emergency release handle down and back (toward the ...
-
Chamberlain 3255 1/2 HP - page 28
CARE OF YOUR OPENER LIMIT AND FORCE ADJUSTMENTS: W eather conditions may cause some minor changes in door operation requiring some re-adjustments, particularly during the first year of operation. Pages 23 and 24 refer to the limit and force adjustments. Only a screwdriver is required. Follow the instructions carefully . Repeat the safety reverse te ...
-
Chamberlain 3255 1/2 HP - page 29
29 HA VING A PROBLEM? 1. My door will not close and the light bulbs blink on my motor unit: The safety reversing sensor must be connected and aligned correctly before the garage door opener will move in the down direction. • V erify the safety sensors are properly installed, aligned and free of any obstructions. Refer to Installation Step 10: Ins ...
-
Chamberlain 3255 1/2 HP - page 30
Bell Wire Safety Re v ersing Sensor Diagnostics Located On Motor Unit LED or Diagnostic LED "Learn" B u tton 30 Installed Safety Re v ersing Sensor Y our garage door opener is programmed with self-diagnostic capabilities. The “Learn” button/diagnostic LED will flash a number of times then pause signifying it has found a potential issu ...
-
Chamberlain 3255 1/2 HP - page 31
*3-Button Remotes If provided with your garage door opener , the large button is factory programmed to operate it. Additional buttons on any Security ✚ ® 3-Button remote or compact remote can be programmed to operate other Security ✚ ® garage door openers. T o Erase All Codes From Motor Unit Memory T o deactivate any unwanted remote, first er ...
-
Chamberlain 3255 1/2 HP - page 32
1. Enter a four digit personal identification number (PIN) of your choice on the keypad. Then press and hold ENTER. 2. While holding the ENTER button, press and hold the LIGHT button on the Multi-Function Door Control. 3. Continue holding the ENTER and LIGHT buttons while you press the push bar on the Multi-Function Door Control (all three buttons ...
-
Chamberlain 3255 1/2 HP - page 33
1 3 4 5 6 2 33 REP AIR P ARTS Rail Assembly Parts KEY P ART NO. NO. DESCRIPTION 1 4A1008 Master link kit 2 41A4813 Chain pulley bracket 3 41A3489 Complete trolley assembly 4 1707LM One-piece rail 5 41D3484 Full chain assembly 6 83A1 1-2 Rail grease 7 U P C E I L I N G M O U N T O N L Y 9 10 NOTICE 5 6 8 4 11 12 3 2 1 L O C K L IG H T Installation P ...
-
Chamberlain 3255 1/2 HP - page 34
Motor Unit Assembly Parts 34 2 10 8 13 14 15 19 4 5 3 9 16 12 18 11 17 1 6 7 D N UP Bro w n W ire (Do w n) Contact LIMIT SWITCH ASSY . Grey W ire Y ello w W ire (Up) Contact Center Limit Contact Dri v e Gear KEY P ART NO. NO. DESCRIPTION 1 31D380 Sprocket cover 2 41C4220A Gear and sprocket assembly Complete with: Spring washer , thrust washer , ret ...
-
Chamberlain 3255 1/2 HP - page 35
35 ACCESSORIES L OCK L I G H T C L OS E D OP E N 373LM 170 8 LM 41A52 8 1 1702LM Outside Quick Release: Required for a garage with NO access door . Enables homeowner to open garage door manually from outside by disengaging trolley . 8 Foot (2.4 m) Complete Rail: T o allow an 8 foot (2.4 m) door to open fully . 1-Button Security ✚ ® Remote Contro ...
-
Chamberlain 3255 1/2 HP - page 36
©2006, The Chamberlain Group, Inc. 1 14A3080E All Rights Reserved LIFTMASTER SER VICE IS ON CALL OUR LARGE SERVICE ORGANIZA TION SP ANS AMERICA INST ALLA TION AND SERVICE INFORMA TION IS AS NEAR AS YOUR TELEPHONE. SIMPL Y DIAL OUR TOLL FREE NUMBER: 1- 8 00-52 8 -2 8 17 www .liftmaster .com For professional installation, parts and service, contact ...
Avez-vous une question à propos de Chamberlain 3255 1/2 HP?
Utiliser le formulaire ci-dessous
Si vous n’avez pas résolu votre problème avec Chamberlain 3255 1/2 HP, avec l'aide du manuel que vous avez trouvé, posez une question en utilisant le formulaire ci-dessous. Si un utilisateur a eu un problème similaire avec Chamberlain 3255 1/2 HP il est probable qu’il a envie de partager la façon de le résoudre.